Table of Contents
Related Manuals for ElectrIQ eiQSLIM100TOUCH
Summary of Contents for ElectrIQ eiQSLIM100TOUCH
- Page 1 USER MANUAL COOKER HOOD eiQSLIM100TOUCH Thank you for choosing electriQ. Please read this user manual before using this Cooker Hood and keep it safe for future reference. Visit our page www.electriQ.co.uk for our entire range of electricals...
-
Page 2: Table Of Contents
CONTENTS Safety Precautions Introduction Unpacking your appliance Product Overview – Parts Supplied Options for Ventilation Installation Operation Maintenance Cleaning your hood Grease filters – cleaning/replacing Carbon Filters (optional) – use and replacement Bulb replacement Troubleshooting Manufacturer Support Technical Specification... -
Page 3: Safety Precautions
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. •... - Page 4 • The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
-
Page 5: Introduction
INTRODUCTION Thank you for choosing your electriQ cooker hood. This instruction manual is designed to provide you with all the required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage. -
Page 6: Product Overview - Parts Supplied
PRODUCT OVERVIEW - PARTS SUPPLIED Description Illustration Qty. Cooker hood Chimney Sections Exhaust Pipe Adaptor Plate I Plate II Screw (4mm x 40mm) Wall plug Screw (4mm x 8mm) Screw (4mm x 30mm) Mounting Bracket Air Flaps... -
Page 7: Options For Ventilation
OPTIONS FOR VENTILATION This hood can be set up for either external venting or recirculation of the air. The type of setup should be decided before commencing installation. EXTERNAL VENTING If you have an outlet to the outside, your cooker hood can be connected as shown in the diagram using the flexible exhaust pipe (supplied). -
Page 8: Installation
INSTALLATION 1. Before installation, ensure you have not connected the appliance to the mains supply. 2. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect. 3. Use the supplied screws (4mm x 40mm) and wall plugs to attach the mounting bracket to the wall in the correct position to set the hood height, ensuring the bracket is kept level. - Page 9 5. The 2 air flaps should now be installed, as access is easier before the unit is wall mounted. The 2 flaps should be carefully installed to the top of the hood unit, bending them slightly so the lugs at each end locate into the holes in the outlet vent.
-
Page 10: Operation
8. Slide the inner chimney upwards and connect it to Plate 2 using the two remaining 4mm x 8mm screws. Before using the hood, read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the identification plate (found inside the cooker hood) and all the data inside the appliance are exactly the same as the voltage and frequency in your home. -
Page 11: Maintenance
MAINTENANCE Before cleaning the hood, it should be switched off and power removed, by removing the plug or if the unit has been hardwired, switching off at the pole switch, to ensure no power is been fed to the unit. Regular Cleaning Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. -
Page 12: Carbon Filters (Optional) - Use And Replacement
CARBON FILTER（OPTIONAL） Activated carbon filters are used to trap odours and must be used if the hood is not vented to the outside. They are available from the same retailer the hood was purchased from under reference: eiQCF110 1. Before installing or replacing the carbon filters, please remove power to the unit. -
Page 13: Bulb Replacement
BULB REPLACEMENT IMPORTANT: The light fitting must be replaced by the manufacturer, its service agent or similarly qualified persons. This hood is fitted with LED light units, which under normal operation can last the lifetime of the hood. In the event that one does fail, replacement light units are available from the same retailer the hood was purchased from. -
Page 14: Troubleshooting
TROUBLESHOOTING Fault Cause Solution The fan blade is Light on, but Switch off the unit. Repair to be jammed. fan does not carried out by qualified service The motor is work personnel only. damaged. Both light Light bulb blown Replace the bulb with correct rating. and fan do Power cord loose Plug in to the power supply again. -
Page 15: Technical Specification
TECHNICAL SPECIFICATION Symbol Value Unit Model identification eiQSLIM100TOUCH Annual Energy 59.0 kWh/a hood Consumption Time increase factor Fluid Dynamic 24.1 hood Efficiency Energy Efficiency 62.6 hood Index Measured airflow rate 348.6 at the best efficiency Measured air pressure at best efficiency point Maximum airflow 605.1... - Page 16 Check with your Local Authority or retainer for recycling advice. electriQ UK SUPPORT www.electriQ.co.uk/support Call: 03303903061 Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.uk...