Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ElectrIQ eiQCHIM60SC
Summary of Contents for ElectrIQ eiQCHIM60SC
- Page 1 USER MANUAL COOKER HOOD eiQCHIM60SC eiQCHIM60WH eiQCHIM60BL eiQCHIM90SC eiQCHIM90BL Thank you for choosing electriQ. Please read this user manual before using this Cooker Hood and keep it safe for future reference. Visit our page www.electriQ.co.uk for our entire range of electricals...
-
Page 2: Table Of Contents
CONTENTS SAFETY PRECAUTIONS OPTIONS FOR VENTILATION UNPACKING YOUR APPLIANCE PRODUCT OVERVIEW INSTALLATION OPERATION MAINTENANCE CARBON FILTERS (OPTIONAL) LIGHT BULB REPLACEMENT TROUBLESHOOTING TECHNICAL INFORMATION MANUFACTURER SUPPORT... -
Page 3: Safety Precautions
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. •... - Page 4 • The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
-
Page 5: Options For Ventilation
OPTIONS FOR VENTILATION This hood can be set up for either external venting or recirculation of the air. The type of setup should be decided before commencing installation. EXTERNAL VENTING If you have an outlet to the outside, your cooker hood can be connected as shown in the diagram using the flexible exhaust pipe (supplied). - Page 6 PARTS SUPPLIED Description Illustration Qty. Cooker hood Chimney Adaptor Cable tie Wall bracket Plate I Plate II Screw (4mm x 30mm) Wall plug Screw (3mm x 10mm) Air Flaps...
-
Page 7: Installation
INSTALLATION 1. Before installation, ensure you have not connected the appliance to the mains supply. 2. The cooker hood should be placed at a distance of 70~80cm above the cooking plane for best effect. Wall plug Screw (4mm x 30mm) Drill 3 holes to accommodate the wall bracket. - Page 8 6. Plate I and II are used to fix the chimney onto the wall. Put the inner chimney into the outer chimney. Mark the position for plate II. Then pull the inner chimney upwards to the desired height, and mark the position of plate I.
- Page 9 10. Put the chimney onto the cooker hood. Attach plate II onto the outer chimney. Lift the inner chimney to the desired height, and attach plate I onto it. There are two methods for attaching the plates to the chimney after the plates have been attached to the wall.
- Page 10 CARBON FILTER (OPTIONAL) Activated carbon filters can be used to trap odours (optional) – and must be used if the hood is not vented to the outside. They are available from the same stockist you purchased the hood from. Part Number: eiQTMCARBONCHIM (Carbon Filter Pack of 2) In order to install the activated carbon filter, the metallic anti-grease filter should be detached first.
-
Page 11: Operation
OPERATION Operation of your hood is extremely simple. There are essentially 3 controls: Power On/Off; Fan Speeds (3 separate buttons) and Illumination. Stop Button Low Speed button Medium Speed button High Speed button Light ON /OFF button... -
Page 12: Maintenance
MAINTENANCE Before cleaning, switch the unit off and pull out the plug, or switch off at the relevant mains switch if the unit has been hard-wired in. Make sure the unit has no power being fed to it. I. REGULAR CLEANING Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. -
Page 13: Iv. Light Bulb Replacement
IV. LIGHT BULB REPLACEMENT This hood is fitted with an LED light unit, which under normal operation can last the lifetime of the hood. In the event that it does fail, replacement light units are available from the same retailer the hood was purchased from. Before changing the fitting, ensure the hood is turned off and the power is removed by either unplugging the unit or switching off at the pole switch (if installed) before attempting to change the bulb. -
Page 14: Troubleshooting
TROUBLESHOOTING Fault Cause Solution Light on, but fan The fan blade is jammed. Switch off the unit. Repair to be carried out does not work The motor is damaged. by qualified service personnel only. Light bulb blown Replace the bulb with correct rating. Both light and fan do not work Power cord loose... -
Page 15: Technical Information
TECHNICAL INFORMATION Value Symbol Value Unit eiQCHIM90SC eiQCHIM60SC Model identification eiQCHIM90BL eiQCHIM60BL eiQCHIM60WH 35.99 37.51 kWh/a Annual Energy Consumption hood 1.655 1.68 Time increase factor 9.95 8.81 Fluid Dynamic Efficiency hood Class E Class E Fluid Dynamic Efficiency class 75.4 77.22... - Page 16 Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with you Local Authority or retainer for recycling advice. electriQ UK SUPPORT www.electriQ.co.uk/support www.electriQ.co.uk...
Need help?
Do you have a question about the eiQCHIM60SC and is the answer not in the manual?
Questions and answers