Table of Contents
Advertisement
Internal I/O Connectors
Expansion Slots
X
X
Please follow the steps below to install the card into the socket.
User's Manual | CMS310
Step 1:
Insert the card into the socket
at an angle while making sure
the notch and key are perfectly
aligned.
Step 2:
Press the end of the card far
from the socket down until
against the stand-off.
Step 3:
Screw tight the card onto the
stand-off with a screw driver
and a stand-off screw until
the gap between the card and
the stand-off closes up. The
card should be lying parallel to
the board when it's correctly
mounted.
Internal I/O Connectors
X
Battery
SYS FAN1 CPU FAN1
7
1
7
USB 3/4
1
DP+
8
2
8
5
+12V Power
Front LAN
Front LAN
LED 1/2
LED 3/4
LAN 1/2
LGA 1200
DP/COM1
HDMI
VGA
LAN3
USB 1/2
(USB 3.1 Gen 1)
LAN4
USB 7/8
(USB 3.1 Gen 2)
M.2 M Key
Mic In
Line Out
Line In
Note
2280
2260
2242
PCIE1 (PCIe x16)
Buzzer
PCIE2 (PCIe x16)
JP2
JP1
6
2
6
2
5
1
5
1
6
2
6
2
PCIE3 (PCIe x4)
JP4
JP3
JP14/13/12/11
5
1
5
1
(right to left)
USB 3.2 Gen 2
1
2
JP15
3
3
3
3
J12
3
2
1
PCIE4 (PCIe x4)
Front
1
1
1
1
9
10
1
5
Audio
JP10/8/6/7
USB 11/12
(left to right)
(USB 2.0)
Note
1
JP24
11
20
3
2
6
2
6
2
1
1
1
S/PDIF
1
1
5
1
5
1
1
10
1
10
2
10
2
Digital I/O (DIO)
USB 9/10 (USB 2.0)
DIO Power
JP5
The lithium ion battery addendum supplies power to the real-time clock and CMOS memory
as an auxiliary source of power when the main power is shut off. Insert a coin cell battery into
the holder and make sure the polarities are correctly oriented — the cap side (rimmed rounded
edge) is negative and should be facing the holder; the flat side with a + mark is positive and
should be facing away from the holder.
Safety Measures
•
• There exists explosion hazard if the battery is incorrectly installed.
•
• Replace only with the same or equivalent type recommended by the manufacturer.
•
• Dispose of used batteries according to local ordinances.
Chapter 2
HARDWARE INSTALLATION
1
DDR4_3
DDR4_4
1
1
2
„ Battery
Battery
14
13
2
1
LPC
12
24
ATX
power
Standby
Power
LED
1
13
1
2
Front
Panel
11
SPI Flash
BIOS
1
2
PS2
DDR4_1
DDR4_2
5
1
9
6
2
JP27
SATA0/1
(left/right)
Intel
SATA2/3
W480E/Q470E
(left/right)
CASE
(USB 5/6)
9
1
2
1
OPEN
3
1
10
2
9
1
1
20
11
M.2 E Key
2
JP26
2230
9
1
2
9
1
6
2
6
1
1
5
1
5
2
SYS FAN3 SYS FAN2
COM1/2/3/4
(top to bottom)
32
Advertisement
Table of Contents
