Table of Contents
Advertisement
3 . 3 .
3 . 3 .
3 .
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
These connectors are for the Serial ATA signal cables to Serial ATA hard
disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0,
RAID 1, RAID 0+1, and software RAID 5 configuration using the Intel
Matrix Storage Technology or RAID 0, RAID 1 and RAID 0+1 configuration
using the LSI MegaRAID
(The server only support two HDD to using RAID 0, 1 configuration.)
These connectors are set I D E
connect Serial ATA boot/data hard disk drives to these connectors. If you
intend to create a Serial ATA RAID set using these connectors, set the
C o n f i g u r e S A T A a s
C o n f i g u r e S A T A a s
C o n f i g u r e S A T A a s item in the BIOS to [RAID]. See section "4.3.4 IDE
C o n f i g u r e S A T A a s
C o n f i g u r e S A T A a s
Configuration" for details.
P5MT-MX/C SATA Connectors
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
•
You must install Windows
Pack 1 before using Serial ATA hard disk drives. The Serial ATA RAID
feature (RAID 0/RAID 1) is available only if you are using Windows
2000/XP.
•
Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
•
When using the connectors in I D E
hard disk drive to the SATA1 or SATA2 connector. Refer to the table
below for the recommended SATA hard disk drive connections.
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
A S U S T S 1 0 0 - E 3
A S U S T S 1 0 0 - E 3
A S U S T S 1 0 0 - E 3
A S U S T S 1 0 0 - E 3
A S U S T S 1 0 0 - E 3
utility embedded on the Intel
®
I D E
I D E
I D E mode by default. In I D E
I D E
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
®
RSATA_RXN3
GND
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
®
2000 Service Pack 4 or Windows
I D E mode, connect the primary (boot)
I D E
I D E
I D E
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
M a s t e r
M a s t e r
M a s t e r
M a s t e r
M a s t e r
®
ICH7R Southbridge.
I D E
I D E
I D E mode, you can
I D E
SATA4
SATA3
SATA2
SATA1
®
®
XP Service
®
3 - 1 1
3 - 1 1
3 - 1 1
3 - 1 1
3 - 1 1
Advertisement
Table of Contents
