Vfd Programming Parameters; (Supply/Relief) - Trane IntelliPak 1 Installation, Operation And Maintenance Manual

Commercial packaged rooftop air conditioners with vav or szvav controls and eflex/ edrive

page of 164

/ 164
Contents
Table of Contents
Bookmarks

Table of Contents

Figure 117. Precision suction restrictor

VFD Programming Parameters (Supply/

Relief)

W W A A R R N N I I N N G G

H H a a z z a a r r d d o o u u s s V V o o l l t t a a g g e e w w / / C C a a p p a a c c i i t t o o r r s s ! !

F F a a i i l l u u r r e e t t o o d d i i s s c c o o n n n n e e c c t t p p o o w w e e r r a a n n d d d d i i s s c c h h a a r r g g e e

c c a a p p a a c c i i t t o o r r s s b b e e f f o o r r e e s s e e r r v v i i c c i i n n g g c c o o u u l l d d r r e e s s u u l l t t i i n n d d e e a a t t h h o o r r

s s e e r r i i o o u u s s i i n n j j u u r r y y . .

D D i i s s c c o o n n n n e e c c t t a a l l l l e e l l e e c c t t r r i i c c p p o o w w e e r r , , i i n n c c l l u u d d i i n n g g r r e e m m o o t t e e

d d i i s s c c o o n n n n e e c c t t s s a a n n d d d d i i s s c c h h a a r r g g e e a a l l l l m m o o t t o o r r s s t t a a r r t t / / r r u u n n

c c a a p p a a c c i i t t o o r r s s b b e e f f o o r r e e s s e e r r v v i i c c i i n n g g . . F F o o l l l l o o w w p p r r o o p p e e r r

l l o o c c k k o o u u t t / / t t a a g g o o u u t t p p r r o o c c e e d d u u r r e e s s t t o o e e n n s s u u r r e e t t h h e e p p o o w w e e r r

c c a a n n n n o o t t b b e e i i n n a a d d v v e e r r t t e e n n t t l l y y e e n n e e r r g g i i z z e e d d . . F F o o r r v v a a r r i i a a b b l l e e

f f r r e e q q u u e e n n c c y y d d r r i i v v e e s s o o r r o o t t h h e e r r e e n n e e r r g g y y s s t t o o r r i i n n g g

c c o o m m p p o o n n e e n n t t s s p p r r o o v v i i d d e e d d b b y y T T r r a a n n e e o o r r o o t t h h e e r r s s , , r r e e f f e e r r t t o o

t t h h e e a a p p p p r r o o p p r r i i a a t t e e m m a a n n u u f f a a c c t t u u r r e e r r ' ' s s l l i i t t e e r r a a t t u u r r e e f f o o r r

a a l l l l o o w w a a b b l l e e w w a a i i t t i i n n g g p p e e r r i i o o d d s s f f o o r r d d i i s s c c h h a a r r g g e e o o f f

c c a a p p a a c c i i t t o o r r s s . . V V e e r r i i f f y y w w i i t t h h a a C C A A T T I I I I I I o o r r I I V V v v o o l l t t m m e e t t e e r r

r r a a t t e e d d p p e e r r N N F F P P A A 7 7 0 0 E E t t h h a a t t a a l l l l c c a a p p a a c c i i t t o o r r s s h h a a v v e e

d d i i s s c c h h a a r r g g e e d d . .

Units shipped with an optional variable frequency drive

(VFD) are preset and run tested at the factory. If a

problem with a VFD occurs, ensure that the

programmed parameters listed in have been set before

replacing the drive.

V V e e r r i i f f y y P P a a r r a a m m e e t t e e r r s s

Verify parameter 1-23 is set to 60 Hz (or 50 Hz where

applicable) and that parameter 0-06 is set to the correct

supply voltage/frequency range.

1. To check parameter 1-23 press the Main Menu

button twice (if TR150 drive) (press the Back button

if the main menu does not display)

2. Scroll down to Load & Motor, press OK

3. Select 1-2, press OK

4. Press down until parameter 1-23 is displayed.

Parameter 1-23 can then be modified by pressing

OK and pressing the Up and Down buttons.

5. When the desired selection has been made, press

OK .

RT-SVX072A-EN

S S e e r r v v i i c c e e a a n n d d M M a a i i n n t t e e n n a a n n c c e e

Should replacing the VFD become necessary, the

replacement is not configured with all of Trane's

operating parameters. The VFD must be programmed

before attempting to operate the unit.

To verify and/or program a VFD, use the following

steps:

1. At the unit, turn the 115 volt control circuit switch

1S70 to the Off position.

2. Turn the 24 volt control circuit switch to the Off

position.