Eflex™ Compressor Vfd Programming; Parameters - Trane IntelliPak 1 Installation, Operation And Maintenance Manual

Table 72. Condenser fan VFD parameters (continued)
Descriptions
Menu ID
8-30
8-31
8-32 Baud Rate
Parity / Stop Bits
8-33
Commu-
nica-
Minimum Response
tions
8-35
Delay (s)
and
Opera-
Maximum Response
tions 8-36
Delay (s)
8-01 Control Site
Control Timeout Time
8-03
Control Timeout
8-04
Function
Switching Frequency
14-01
Mains Voltage Fault
14-11
level (V)
Special
Function at Main
Func-
14-12
Imbalance
tions
14-20 Reset Mode
14-50 RFI Filter
Function at Inverter
14-61
Overload
eFlex™ Compressor VFD Programming

Parameters

W W A A R R N N I I N N G G
H H a a z z a a r r d d o o u u s s V V o o l l t t a a g g e e w w / / C C a a p p a a c c i i t t o o r r s s ! !
F F a a i i l l u u r r e e t t o o d d i i s s c c o o n n n n e e c c t t p p o o w w e e r r a a n n d d d d i i s s c c h h a a r r g g e e
c c a a p p a a c c i i t t o o r r s s b b e e f f o o r r e e s s e e r r v v i i c c i i n n g g c c o o u u l l d d r r e e s s u u l l t t i i n n d d e e a a t t h h o o r r
s s e e r r i i o o u u s s i i n n j j u u r r y y . .
D D i i s s c c o o n n n n e e c c t t a a l l l l e e l l e e c c t t r r i i c c p p o o w w e e r r , , i i n n c c l l u u d d i i n n g g r r e e m m o o t t e e
d d i i s s c c o o n n n n e e c c t t s s a a n n d d d d i i s s c c h h a a r r g g e e a a l l l l m m o o t t o o r r s s t t a a r r t t / / r r u u n n
c c a a p p a a c c i i t t o o r r s s b b e e f f o o r r e e s s e e r r v v i i c c i i n n g g . . F F o o l l l l o o w w p p r r o o p p e e r r
l l o o c c k k o o u u t t / / t t a a g g o o u u t t p p r r o o c c e e d d u u r r e e s s t t o o e e n n s s u u r r e e t t h h e e p p o o w w e e r r
c c a a n n n n o o t t b b e e i i n n a a d d v v e e r r t t e e n n t t l l y y e e n n e e r r g g i i z z e e d d . . F F o o r r v v a a r r i i a a b b l l e e
f f r r e e q q u u e e n n c c y y d d r r i i v v e e s s o o r r o o t t h h e e r r e e n n e e r r g g y y s s t t o o r r i i n n g g
c c o o m m p p o o n n e e n n t t s s p p r r o o v v i i d d e e d d b b y y T T r r a a n n e e o o r r o o t t h h e e r r s s , , r r e e f f e e r r t t o o
t t h h e e a a p p p p r r o o p p r r i i a a t t e e m m a a n n u u f f a a c c t t u u r r e e r r ' ' s s l l i i t t e e r r a a t t u u r r e e f f o o r r
a a l l l l o o w w a a b b l l e e w w a a i i t t i i n n g g p p e e r r i i o o d d s s f f o o r r d d i i s s c c h h a a r r g g e e o o f f
c c a a p p a a c c i i t t o o r r s s . . V V e e r r i i f f y y w w i i t t h h a a C C A A T T I I I I I I o o r r I I V V v v o o l l t t m m e e t t e e r r
r r a a t t e e d d p p e e r r N N F F P P A A 7 7 0 0 E E t t h h a a t t a a l l l l c c a a p p a a c c i i t t o o r r s s h h a a v v e e
d d i i s s c c h h a a r r g g e e d d . .
A factory-shipped TRV200 should not be modified in
the field. It is specifically matched to the compressor.
RT-SVX072A-EN
Parameter Setting
[2] Modbus RTU
Protocol
Set address per unit component location diagram
[5] for 1A (REFDES 2M6) [
Address
6] for 2A (REFDES 2M9)
[7] 115200 Baud
[0] Even Parity,1 Stop Bits
[0.005] 5ms Min Response Delay Time
[0.1] 100ms Max Response Delay Time
[2] Controlword only
[15] 15s
(s)
[2] Stop
[5] 5.0 kHz
(kHz)
Set based on motor nameplate voltage
[391] for 460V motor
[489] for 575V motor
[3] Derate
[3] Automatic reset x 3
[0] Off
[1] Derate
S S e e r r v v i i c c e e a a n n d d M M a a i i n n t t e e n n a a n n c c e e
Should replacing a VFD become necessary, refer to . All
other parameters will be appropriately set in field
replacement VFDs. Do not use any other type or brand
of VFD when replacing the VFD.
N N o o t t e e : : Failure to set parameter 4-18 Current Limit on a
field replacement VFD will not allow the
compressor to start and result in A18 Start Failed
or A49 Speed Limit on the VFD.
To verify and/or set parameters in the Compressor
VFD:
1. Press Q Q u u i i c c k k M M e e n n u u .
2. Press M M y y P P e e r r s s o o n n a a l l M M e e n n u u .
3. Navigate through the options using the U U p p and
D D o o w w n n arrows to parameter.
4. Adjust the value as shown in .
5. Press [OK].
151