Supermicro SuperStorageSystem SSG-2028R-DN2R24L User Manual page 62

SUPERSTORAGESYSTEM SSG-2028R-DN2R24L User's Manual
USB 3.0 Support
Select Enabled for USB 3.0 support. The options are Smart Auto, Auto, Enabled,
and Disabled.
EHCI1
Select Enabled to enable EHCI (Enhanced Host Controller Interface) support on
USB 2.0 connector #1 (-at least one USB 2.0 connector should be enabled for EHCI
support.) The options are Disabled and Enabled.
EHCI2
Select Enabled to enable EHCI (Enhanced Host Controller Interface) support on
USB 2.0 connector #2 (-at least one USB 2.0 connector should be enabled for EHCI
support.) The options are Disabled and Enabled.
XHCI Pre-Boot Driver
Select Enabled to load Intel XHCI pre-boot driver. The settings are Enabled and
Disabled.
sSATA Configuration
When this submenu is selected, AMI BIOS automatically detects the presence of
the s-SATA devices that are supported by the PCH-sSATA controller and displays
the following items:
sSATA Controller
This item enables or disables the onboard SATA controller supported by the Intel
PCH chip. The options are Enabled and Disabled.
Configure sSATA as
Select IDE to configure an sSATA drive specified by the user as an IDE drive. Select
AHCI to configure an sSATA drive specified by the user as an AHCI drive. Select
RAID to configure an sSATA drive specified by the user as a RAID drive. The op-
tions are IDE, AHCI, and RAID.
*If the item above "Configure sSATA as" is set to AHCI, the following items will
display:
sSATA AHCI ALPM
Select Enabled for the sSATA controller to automatically generate link requests in
partial or slumber mode when there is no commands for the system to execute.
The options are Disabled, and Enabled.
7-18
sSATA Port 0~ Port 3
This item displays the information detected on the installed on the sSATA port,
specified by the user.
•
Model number of drive and capacity
sSATA Port 0~ Port 3
Select Enabled to enable an sSATA port specified by the user. The options are
Disabled and Enabled.
sSATA Port 0 ~ Port 3 Hot Plug
Select Enabled to enable hot-plugging support for a port specified by the user,
which will allow the user to replace a sSATA disk drive installed on this port
without shutting down the system. The options are Enabled and Disabled.
sSATA Port 0 ~ Port 3 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE-
SET initialization to the device. The options are Enabled and Disabled.
Port 0 ~ Port 3 sSATA Device Type
Use this item to specify if the sSATA port specified by the user should be con-
nected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to IDE, the following items will
display:
sSATA Port 0~ Port 3
This item indicates that an sSATA port specified by the user is installed (present)
or not.
Port 0~ Port 3 sSATA Device Type (Available when a sSATA port is
detected)
Use this item to specify if the sSATA port specified by the user should be con-
nected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to RAID, the following items will
display:
sSATA AHCI ALPM
Select Enabled for the sSATA controller to automatically generate link requests in
partial or slumber mode when there is no commands for the system to execute.
The options are Disabled, and Enabled.
7-19
Chapter 7: AMI BIOS