Maintenance Schedule; Self-Propelled Mower Conditioner - MacDon A30-S Operator's Manual

7.18 MAINTENANCE SCHEDULE

The following maintenance
periodic maintenance procedures, and are
organized by service
maintenance is the best insurance against early
wear and untimely breakdowns. Following this
schedule will increase machine life. For detailed
instructions, refer to the specific headings in
Section 6 MAINTENANCE AND SERVICING.
Recommended service intervals are in hours of
operation. Where a service interval is given in
more than one time frame, e.g. "100 hours or
Annually", service the machine at whichever
interval is reached first.

7.18.1 Self-Propelled Mower Conditioner

Refer to your Windrower Operator's Manual for windrower maintenance.
7.18.1.1 Break-In Inspection: Self-Propelled
HOURS
5
5, 25,
and 50
10
7.18.1.2 Interval Maintenance: Self-Propelled
INTERVAL
FIRST USE
1. Check Conditioner Drive Gearbox Lubricant
100 HOURS OR
ANNUALLY *
2. Check Wobble Box Lubricant Level.
END OF SEASON
1. Check Hydraulic Hoses And Lines For Leaks.
10 HOURS OR 2. Oil Sickle (Except In Sandy Conditions).
DAILY
3. Check Sickle Sections, Guards, and Hold-
25 HOURS 1. Grease Sickle Head.
1. Grease Reel Shaft Bearings.
2. Grease Auger Shaft Bearings.
3. Grease Auger Jack-Shaft Bearings (except
50 HOURS
4. Grease Conditioner Universal Shafts.
5. Grease Conditioner Shaft Bearings.
6. Grease Roll Pivots Bearing.
1000 HOURS OR
1. Change Wobble Box Lubricant.
3 YEARS
Form 169000 / 169040
SECTION 7 MAINTENANCE AND SERVICING
schedules
intervals. Regular
The following service schedule is only applicable to the Auger Header.
ITEM
Hardware
Auger Drive Belt
Reel Drive Belt
Sickle Drive Belt
Auger Drive Chain
Reel Drive Chain
Wobble Box Mounting Bolts
Refer To Section 7.18.1.1 Break-In Inspection: Self-Propelled
Level.
Downs.
A40-D).
Recommended intervals are for average
conditions. Service the machine more
list
often if operated under adverse conditions
(severe dust, extra heavy loads, etc.).
Carefully follow safety messages given
under Section 7.2 RECOMMENDED SAFETY
PROCEDURES.
NOTE
CHECK
Torque
Tension
Tension / Lubrication
Torque
SERVICE
3. Check Wobble Box Mounting Bolt
Torques.
Refer To Section 6.19 STORAGE.
4. Oil Reel Drive Chain (except A40-D).
5. Oil Auger Drive Chain (except A40-D).
6. Check Wobble Box Bolt Torque (First 10
Hours Only; Every 100 Hours Thereafter).
7. Grease Tine Tube Bearings (A40-D).
8. Grease Gauge Roller Bearings.
9. Change Wobble Box Lubricant. (First 50
Hours Only; Every 1000 Hours Thereafter).
10. Change Conditioner Drive Gearbox
Lubricant (First 50 Hours Only; Every 1000
Hours Thereafter).
2. Change Conditioner Drive Gearbox
Lubricant.
177
IMPORTANT
CAUTION
REFERENCE
Section 7.3.1
Sections 7.11.3 and 7.11.4
Section 7.9.2
Sections 7.8.9, 7.8.10, and 7.8.11
Sections 7.11.1 and 7.11.2
Section 7.9.1
200 ft·lbf (270 N·m) Section 7.8.13
Revision D