Room 2 Source Playback - Sherwood Newcastle R-871 Operating Instructions Manual

ROOM 2 SOURCE PLAYBACK

• This function allows enjoying one source in the main room and playing another in a different room at the same time.
• When you connect the multi-room system kit to the IR IN jack of this receiver, you can control this receiver with not only the
universal remote control unit but also the ROOM 2 remote control unit in a different room, too. (For details, refer to
"CONNECTING MULTI-ROOM SYSTEM KIT" on page 13 and "ROOM 2 Remote Controls" on page 28.)
Notes:
• The analog signals from the EXTERNAL INs and the digital signals cannot be output to the different room, meaning no
playback in a different room.
• You cannot play the ROOM 2 source in any surround mode.
■When using the buttons on the remote control unit.
Press the ROOM 2 button.
1
• ROOM 2 ~ is displayed for several seconds.
• Each time this button is pressed, the ROOM 2 mode
changes as follows :
ON : To turn on the ROOM 2
function. (" " lights up.)
OFF : To turn it off. ("
goes off depending on the AMP ASSIGN setting.)
Note :
• When the ROOM 2 mode is set to OFF, you cannot
adjust the ROOM 2 volume.
Select the desired input as a ROOM 2 source.
2
• Each time the INPUT button
on the universal remote
control unit is pressed, the
ROOM 2 input can be
selected among MAIN
source, TUNER, CD, AUX,
TAPE, VIDEO 1 ~ VIDEO 5.
Adjust the ROOM 2 volume.
3
• You can adjust the volume on the power amplifier
assigned to ROOM 2 when the SURROUND BACK/
ROOM 2 speaker terminals are connected to the
speakers in a different room. (For details, refer to "When
selecting the AMP ASSIGN" on page 49.)
• The MUTE button on the ROOM 2 remote control unit can
be available only when the ROOM 2 function is operating.
4
Start play on the component related to the
ROOM 2 source.
Notes:
• When the EXTERNAL IN is selected as a main input, if the MAIN source is selected as a ROOM 2 input, no audio signals
can be heard in the different room (ROOM 2).
• Even when this receiver enters the standby mode, in such a case that "
ON/STANDBY button lights up in blue as it does in the operating mode, meaning only the ROOM 2 circuitry operates, the
ROOM 2 source can be played independently.
• When you do not use the ROOM 2 function, turn off the ROOM 2 function to save electricity.
" or " "
46
■When using the buttons on the front panel.
Press the ROOM 2 button to enter the
1
ROOM 2 mode.
• ROOM 2 ~ is displayed for several seconds.
• When the ROOM 2 setting mode disappears,
press the ROOM 2 button again.
2
Select the desired mode while displaying
the ROOM 2 setting mode.
• Each time these buttons are pressed,
the mode changes as follows :
ROOM 2 ~ : To turn on or
(ROOM 2 mode) off the ROOM 2
function.
INPUT ~ : To select the desired
(ROOM 2 input) ROOM 2 source.
VOLUME ~ : To adjust the volume on the power
(ROOM 2 volume) amplifier assigned to ROOM 2.
Note : When the ROOM 2 mode is set to OFF,
the ROOM 2 input and the ROOM 2 volume
cannot be selected
Set the selected mode as
3
desired.
■When selecting the ROOM 2 mode.
ON : To turn on the ROOM 2 function.
(" " lights up.)
OFF : To turn it off. (" " or "
depending on the AMP ASSIGN setting.)
■When selecting the ROOM 2 input.
• You can select the desired among MAIN source,
TUNER, CD, AUX, TAPE, VIDEO 1 ~ VIDEO 5 as a
ROOM 2 source.
■When selecting the ROOM 2 volume.
• You can adjust the volume on the power amplifier
assigned to ROOM 2 when the SURROUND BACK/
ROOM 2 speaker terminals are connected to the
speakers in a different room. (For details, refer to "When
selecting the AMP ASSIGN" on page 49.)
4
Start play on the component related to the
ROOM 2 source.
" lights up still and the POWER
" goes off