RD-6513(A) 2008.8.21 12:19 PM 페이지 3 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
RD-6513(A) 2008.8.21 12:19 PM 페이지 4 Introduction READ THIS BEFORE OPERATING YOUR UNIT TO REDUCE THE RISK OF ELECTRIC SHOCK, CAUTION : DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
RD-6513(A) 2008.8.21 12:19 PM 페이지 5 CONTENTS • IMPORTANT SAFETY INSTRUCTIONS ... 3 Introduction • READ THIS BEFORE OPERATING YOUR UNIT ... 4 System Connections ... 6 Front Panel Controls ... 11 Remote Controls ... 13 • REMOTE CONTROL OPERATION RANGE ... 14 •...
RD-6513(A) 2008.8.21 12:19 PM 페이지 6 System Connections • Do not plug the AC input cord into the wall AC outlet until all connections are completed. • Be sure to observe the color coding when connecting audio, video and speaker cords.
RD-6513(A) 2008.8.21 12:19 PM 페이지 7 CONNECTING VIDEO COMPONENTS • The jacks of VIDEO 1 may also be connected to a DVD recorder or other digital video recording component. For details, refer to the operating instructions of the component to be connected.
Page 7
RD-6513(A) 2008.8.21 12:19 PM 페이지 8 CONNECTING AUDIO COMPONENTS • The TAPE IN/OUT jacks can be connected to audio recording equipment such as a tape deck, an MD recorder, etc. CONNECTING EXTERNAL INs • Use these jacks to connect the corresponding analog outputs of 6 CH decoder or DVD player with 6 CH output for Dolby Digital or DTS, etc.
RD-6513(A) 2008.8.21 12:19 PM 페이지 9 CONNECTING DIGITAL INs • The OPTICAL and the COAXIAL DIGITAL OUTs of the components that are connected to CD and VIDEO 1 ~ VIDEO 2 of this unit can be connected to these DIGITAL INs.
Page 9
RD-6513(A) 2008.8.21 12:19 PM 페이지 10 AC INPUT CORD • Plug the cord into a wall AC outlet. Speaker placement Ideal speaker placement varies depending on the size of your room and the wall coverings, etc. The typical example of...
RD-6513(A) 2008.8.21 12:19 PM 페이지 11 Front Panel Controls 1. POWER switch 2. POWER ON/STANDBY button 3. STANDBY indicator 4. FLUORESCENT DISPLAY For details, see below. 5. VIDEO INPUT SELECTOR button 6. AUDIO INPUT SELECTOR button 7. EXT.IN SELECTOR button 8.
Page 11
(For information on Sherwood Audio Receiver BT-R7, contact your dealer.) • The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sherwood Corporation is under license. Other trademarks and trade names are those of their respective owners.
RD-6513(A) 2008.8.21 12:19 PM 페이지 13 Remote Controls Note : • Some buttons (USB, VIDEO 3, AUX and USB transport buttons) are not available for this receiver.
RD-6513(A) 2008.8.21 12:19 PM 페이지 14 REMOTE CONTROL OPERATION RANGE LOADING BATTERIES Remove the cover. • Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor.
RD-6513(A) 2008.8.21 12:19 PM 페이지 15 Operations Note : Before operating this receiver, first set this unit as desired for optimum performance, doing the system setup procedures. (For details, refer to "System Setup" on page 29.) LISTENING TO A PROGRAM SOURCE Before operation •...
Page 15
RD-6513(A) 2008.8.21 12:19 PM 페이지 16 When CD, VIDEO 1~ 2 is selected as an input source Select the digital or the analog input connected as desired. • Each time this button is pressed, the corresponding input is selected as follows: →...
Page 16
RD-6513(A) 2008.8.21 12:19 PM 페이지 17 Adjusting the tone (bass and treble) Enter the tone mode. • The tone mode is displayed for several seconds. Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired tone mode. • Each time these buttons are pressed, the tone mode is...
RD-6513(A) 2008.8.21 12:19 PM 페이지 18 SURROUND SOUND • This receiver incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound atmosphere in your personal Home Theater. Surround modes ■DTS Digital Surround DTS Digital Surround(also called simply DTS) is a multi- channel digital signal format which can handle higher data rates.
RD-6513(A) 2008.8.21 12:19 PM 페이지 19 ENJOYING SURROUND SOUND Notes: • Before surround playback, first perform the speaker setup procedure, etc. on the SETUP menu for optimum performance. (For details, refer to "SETTING THE SPEAKER SETUP" on page 34.) • When the EXTERNAL IN is selected as an input source, the surround modes cannot be selected.
Page 19
RD-6513(A) 2008.8.21 12:19 PM 페이지 20 When adjusting the sound parameters • While playing digital signals from Dolby Digital or DTS program source or listening in Dolby Pro Logic II Music mode, you can adjust their parameters for optimum surround effect.
Page 20
RD-6513(A) 2008.8.21 12:19 PM 페이지 21 Adjusting each channel level with test tone • The volume level of each channel can be adjusted easily with the test tone function. Note : When the SPEAKER button is set to off, the test tone function does not work.
Page 21
RD-6513(A) 2008.8.21 12:19 PM 페이지 22 Adjusting the current channel level • After adjusting each channel level with test tone, adjust the channel levels either according to the program sources or to suit your tastes. • You can adjust the current channel levels as desired. These adjusted levels are just memorized into user’s memory ("CAL"), not into preset memory("REF 1", "REF 2").
Page 22
RD-6513(A) 2008.8.21 12:19 PM 페이지 23 Memorizing the adjusted channel levels • You can memorize the adjusted channel levels into preset memory("REF 1", "REF 2") and recall the memorized whenever you want. After performing the steps 1 ~ 4 in "Adjusting the current channel level" procedure on page 22, press the (MEMORY/)ENTER button.
RD-6513(A) 2008.8.21 12:19 PM 페이지 24 LISTENING TO RADIO BROADCASTS Auto tuning Select the desired band. • Each time this button is pressed, the band changes as follows ; → FM ST → FM MONO → AM ("ST" lights up) ("ST"...
Page 24
RD-6513(A) 2008.8.21 12:19 PM 페이지 25 Manual presetting • You can store up to 30 preferred stations in the memory. Tune in the desired station with auto or manual tuning. Press the (MEMORY/)ENTER button. • "MEM" is flickering for several seconds.
RD-6513(A) 2008.8.21 12:19 PM 페이지 26 RECORDING • The analog signals from the EXTERNAL INs as well as the digital signals from the coaxial or optical digital input can be heard but cannot be recorded. • When recording the analog signals from CD, VIDEO 1 ~ 2, be sure to select th analog input.
Page 26
RD-6513(A) 2008.8.21 12:19 PM 페이지 27 Dubbing the audio and video signals separately onto VIDEO 1 Example) When dubbing the VIDEO 2 video signal and the CD audio signal separately onto VIDEO 1. Select VIDEO 2 as a video recording source.
RD-6513(A) 2008.8.21 12:19 PM 페이지 28 OTHER FUNCTIONS Operating the sleep timer • The sleep timer allows the system to continue to operate for a specified period of time before automatically shutting off. • To set the receiver to automatically turn off after the specified period of time.
RD-6513(A) 2008.8.21 12:19 PM 페이지 29 System Setup • The setup menu is displayed on the fluorescent display and allows you to perform the setup procedures easily. In most situations, you will only need to set this once during the installation and layout of your home theater, and it rarely needs to be changed later.
Page 29
RD-6513(A) 2008.8.21 12:19 PM 페이지 30 ■Setup menu flow • The setup menu flow is as follows : • When "RETURN" is selected on a sub-menu, it will return to the previous menu. ■Note : • During setup menu operation, only the (POWER ON/) STANDBY button and the buttons required for system setup will...
RD-6513(A) 2008.8.21 12:20 PM 페이지 31 SETTING THE SYSTEM • SW (SUBWOOFER) : To select the desired subwoofer mode. • TONE : To adjust the tone (bass and treble) as desired. • RMEQ (ROOM EQ) : To select the desired room EQ mode.
Page 31
RD-6513(A) 2008.8.21 12:20 PM 페이지 32 When selecting the TONE OFF : To listen to a program source without the tone effect. ("DIR" indicator lights up.) ↕ ON : To adjust the tone for your taste. ("DIR" indicator goes off.) ■Note :...
RD-6513(A) 2008.8.21 12:20 PM 페이지 33 SETTING THE INPUT • D.IN (DIGITAL IN) : To assign the connected DIGITAL INs to the desired input. • AUTO (AUTO SURROUND) : To select the auto surround mode or the manual surround mode.
RD-6513(A) 2008.8.21 12:20 PM 페이지 34 When selecting the DIGITAL IN • You should assign the connected DIGITAL INs to the desired of CD and VIDEO 1 ~ VIDEO 2. (For details, refer to "CONNECTING DIGITAL INs" on page 9.) •...
Page 34
RD-6513(A) 2008.8.21 12:20 PM 페이지 35 When selecting the AUTO SETUP • Auto Setup lets you avoid troublesome listening-based speaker setup and achieve good surround sound. You should connect the supplied microphone to the SETUP MIC jack so that this receiver can analyze the information from a series of test tones emitted from speakers and can adjust the configuration, distance, sound level and frequency response of each speaker automatically.
Page 35
RD-6513(A) 2008.8.21 12:20 PM 페이지 36 When selecting the CONFIGURATION Press the CURSOR UP(▲)/DOWN(▼) buttons to select the "CONFIG", then press the ENTER button. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired speaker. Press the CURSOR LEFT(◀)/ RIGHT(▶) buttons to set the selected speaker as desired.
Page 36
RD-6513(A) 2008.8.21 12:20 PM 페이지 37 When selecting the DISTANCE Press the CURSOR UP(▲)/DOWN(▼) buttons to select the DISTANCE, then press the ENTER button. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired speaker. Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to set the selected speker as desired.
Page 37
RD-6513(A) 2008.8.21 12:20 PM 페이지 38 When selecting the CROSSOVER • When speakers are set to "S (Small)", be sure to set their crossover frequency correctly according to their frequency characteristics. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the "X-OVER", then press the ENTER button.
RD-6513(A) 2008.8.21 12:20 PM 페이지 39 SETTING THE CH LEVEL Note : Depending on the speaker settings ("N (None or No)"), some channels cannot be selected. Adjusting the current channel level • You can adjust the current channel levels as desired. These adjusted levels are just memorized into user’s memory("CAL"), not into preset memory ("REF 1", "REF 2")
Page 39
RD-6513(A) 2008.8.21 12:20 PM 페이지 40 Memorizing the adjusted channel levels • You can memorize the adjusted channel levels into preset memory("REF 1", "REF 2") and recall the memorized whenever you want. After performing the steps 1 ~ 3 in "Adjusting the current channel level" procedure on page 39, press the ENTER button.
RD-6513(A) 2008.8.21 12:20 PM 페이지 41 SETTING THE PARAMETER • NIGHT M (NIGHT MODE) : To adjust the dynamic range compression that makes faint sound easier to hear at low volume levels. • PLII MSC (DOLBY PLII MUSIC) : To adjust the various surround parameters for optimum surround effect.
Page 41
RD-6513(A) 2008.8.21 12:20 PM 페이지 42 When selecting the DOLBY PLII MUSIC • You can adjust the various surround parameters for optimum surround effect. Note: The parameter settings are valid only when listening in Dolby Pro Logic II Music mode.
RD-6513(A) 2008.8.21 12:20 PM 페이지 43 Troubleshooting Guide If a fault occurs, run through the table below before taking your receiver for repair. If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult your dealer.