Motorola SABER I User Manual page 88

H7O7
-
1
Tone Slngletone vla
PTT
Button
When selecting
this option a popup window is displayed and you are asked to enter
a
lrequency
tor single
tonel.
lt
H707 is enabled, RAT1 and RAT2 buttons are disabled and single
tonel
is
sent out through PTT on all channels. This
optaon
is incompatibte
with all the MDC Unit lD
Prr)
options. The valid
range for single
tonel
is
from 300 Hz to 3000 Hz in increments of
1
Hz.
This
option is
irrompatible
with the lollowing options:
Singletones
- General
(PTT/RATs)
H742-
2
Tone Singletone via
RAT Buttons.
Allthe
MDC Unit lD (PTD Options.
The following options are enabled
if
you select this
option
:
Singletone Non-Std. Pretime
Singletone Time Duration
H619
-Omit MDC
Side Tones
H742
-
Up
to
2 Singletones via RAT Buttons
This option is very similar to the Singtetone
-
General
option.
When selecting this option two
pop-up windows are displayed on the screen sequentially. Enter a frequency in both the
windows. l, this
option is enabled and none of the MDC Unit lD oBtions are selected then
sQnalling
on
PTT
is
disabled.
!l this
oplion is selected along with any of the MDC Unit lD options
then MDC Unit !D
is
sent out via PTT. Single tonel
is sent
out
through
RAT1
and single tone2 is
sent out through RAT2. You may leave the default single tone 2frequency, in case you need
only one single tone.This option
is
incompatible with the lollowing options:
Singletone - General
(PTT/RATs)
_.--l=1707---1-Tone-singte-tone-via-PTl'-Buuon---
'
Multiple Repeater Access Codes -
MDC 600
Multiple Repeater Access Codes - MDC 1200
The
lollowing optlons are enabled
if
you select this option
Singletone Non-Std. Pretime
Singletone Time Duration
H619
-Omit MDC
Sicle
Tones
Singletone Non-Std. Pretime
To select
this option you must select either
Singletones
-
General
or H707 or
H742. When
selecting
this option a pop-up window will be
displayed
on the screen and you will be asked to
enler a pretime value. Pretime is the time for which the unmodulated caraer goes out
before
sending
the signal out to bring up the repeater. The valid range
is lrom 0
to
1000 ms in
increments of
10
nrs.
The delault vatue is set to 40 ms.
Singletone Time Duration
To
seled this option you must select Singletones
-
General
or H707 or H742. When selecting this
oPtion
a pop-up window witl be displayed on the screen and you will be asked to enter a time
duration value. The valid range
is 0 to 20,000
ms
in
increments
ol
10 ms.
lf
option H707 is
selecled.
the valid
range lor single tone time duration
is
from
1
to 20,000 ms in increments of
10
ms.
When'0'is
entered as single tone time duration, the process ol
transmitting single tones
becomes
manual. ln
manual
process you must press PTT for the period of time you want to
transmit
ihe
singletones. The manual timing and H707 are incompatible. The delault
value lor
the time
duration is 600 ms, il this option is not selected.
Appendix - 5. Options List
and
Delinitions
81