Motorola SABER I User Manual page 84

Desig
nated Tnnsmit Mode
This option will lorce you to transmit on a specific channel anytime the PTT is pressed while
scannirg rcgardless ol what state the scanner is
in.
The designated transmit channelwill
be
specilied
per scan last. lf this option is selecled along with lloating priority, the floating
priority
channel will always be the designated transmit channel
Since
this is always the channel
of
transmission. lf you
do not select this option then ror each scan list,
ransmit channelwill
always
be
the
channel on
which the radio was when
scan
was
entered.
Prbdtyto Folbw
Channel Selector Switch
Sebaing
this option
will
assign
priodty channel
1
to the position
of
the channel selector sritch.
For exanple,
if
you are on channel
5
then
your pdorily
channel 1 is assigned to
channel
5.
lf yo.r
change
the position ol the channel selector srilch while scannirq, the radio witl exit the
scan
mode. The channelselected
to
be
the priority channel must be chosen before activating scan.
/l,tto*an
This
optbn npdlfies the behavior of mode-shved scan (H344) such that, when a channel
is
selected
on lhe radio, scanning wit! begin immediately if there is a scan list assigned to that
channel. This reature is only availabte in zone/channel radios, and
is not
compatible with
ope
rator-seleclable scan.
Required
oflions:
H344, H371, H669
lnoompatible
options:
H396, H397, H273, and Nuisance Delete
Mode
Slavd
Scan
(forSABER
ll.2)
--ThiS-optaon is
available
onl[i-n SIBEhTi.Tradjo$
il-alm5
only Z-s-can IisG. -SEiedi-ndr
llia5
-
option
willgive you 2 scan
lists
wilh
13
entries per scan
list.
The
13 entries
include: 2 prioriU
channels, 10 nonpriority channels, and 1 optional entry ,or the designated transmit channel.
The two prbdty channels wit! be scanned more often than the non-priority channels and
witt
continue
to
be scanned even
il a
lower priority channel is currently being
nonitored. l,
both
priority channels are used,
the
channelwith
priority
1 status
will ovenide a
priortty
2
channel
such
that the priortty
1
channelwill
continue
to be
scanned
even if the
priority 2 channel is
aclive.
ln
any
scan list
it
will be possible to omit either
or both of
the
priority channels. Wth this
option you
can only have 3 zones/36 channels (see option
H371
-
zone and channel operation). The
nuisance
rnode delete option, scroll
scan list option, and autoscin are not available with this
option.
H444
-
Delete Proper Code Detect
ll this option is
enabled
the radio.will
mute on any
signal. ll
a
coded signal with different key is
present
the
radio
wall
unmute
with
encrypted
data
which will sound like noise to the
user.
H245
-
Delete Clear Mode Atert Tones on Transmit
This opt'on willdelete the
alert tone
that is
used
to
indicate that
the radio is transmitting in the
clear
npde.
The frequerrcy
of
this tone
is
820 Hz
lor
a
duration of 80
ms.
You can only mute this
tone
using the Radio Service Software.
H244
-
Delete Clear Coded
Transmit Switch
!l your radio is
SECURE and
does not have a coded/clear selector
switch, you must
enable
this
optaon; othenrvise,
you
may electronically disable this option.
ll your
radio is
not a SECURE radio
you
will not even see this option on the
screen.This
option
is incompatible with option
H400 -
Secure Voice Slaved
to a Mode, when selected all channels are assumed to
be
toded.'
Appendix - 5. Options List and
Delinitions Tl