Skyjack SJKB-40-D Operating Maintenance Instructions & Part List page 19

WARNING
DO NOT operate any control on the operator's control
console without your safety devise fastened and properly
securing the safety lanyard to the platform lanyard rings.
Failure to avoid this hazard could result in death or
serious injury!
5. Attach the safety lanyards of each occupant to
the platform lanyard rings.
6. Pull out the Emergency Stop Button.
7. For gas engine machines equipped with the
Dual Fuel Option. Select the desired fuel source.
8. When the engine is cold, press and hold the
Engine Choke Toggle Switch to the " ð
(right) position while starting engine. Release
switch once the engine starts (Kubota gas
engines) or press and hold Glow Plug Toggle
Switch to the " ð " (right) position for 15 to 20
seconds, then release (Diesel engines).
9. Turn Engine Stop/Run/Start Select Switch to the
" " (start) position until engine starts, then
release. DO NOT over crank the starter. (If
engine fails to start after multiple attempts,
consult the TROUBLE SHOOTING section in
the Operational Maintenance and Parts
Manual). NOTE Engine will not start if foot
switch is depressed.
10. Select desired engine RPM using the Engine
Speed Select Switch.
REMEMBER
The following controls on the Operator's Control
Console WILL NOT operate unless the Foot Switch
is depressed and held.
When the operator is positioned over an axle, the
direction the operator is facing will be FORWARD!
11. TO DRIVE FORWARD: Slowly move the Drive/
Steer Controller handle to the " ñ " (forward)
position. Release controller handle to stop.
12. TO DRIVE IN REVERSE: Slowly move the
Drive/Steer Controller handle to the " ò "
(reverse) position. Release controller handle
to stop.
13. TO STEER: Depress the rocker on the Drive/
Steer Controller handle in the direction you wish
to steer.
SECTION 2, Page 8
NOTE
14. TO ADJUST BOOM FUNCTION SPEED: Turn
the Boom Speed Control Knob counter-
clockwise to decrease function speed or
clockwise to increase funtion speed. The Boom
Speed Control will affect all lifting, lowering and
rotate functions but will not affect drive or steer
speed.
15. TO MOVE THE JIB UPWARD: Press and hold
the Jib Up/Down Toggle Switch to the " ñ "
(up) position. Release the switch to stop.
16. TO MOVE THE JIB DOWNWARD: Press and
hold the Jib Up/Down Toggle Switch to the " ò "
(down) position. Release the switch to stop.
17. TO MOVE THE RISER UPWARD: Press and
"
hold the Riser Up/Down Toggle Switch to the
" ñ " (up) position. Release the switch to stop.
18. TO MOVE THE RISER DOWNWARD: Press
and hold the Riser Up/Down Toggle Switch to
the " ò " (down) position. Release the switch
to stop.
19. TO MOVE THE BOOM UPWARD: Press and
hold the Boom Up/Down Toggle Switch to the
" ñ " (up) position. Release the switch to stop.
20. TO MOVE THE BOOM DOWNWARD: Press
and hold the Boom Up/Down Toggle Switch to
the " ò " (down) position. Release the switch
to stop.
21. TO ROTATE THE TURRET LEFT: Press and
hold the Turret Rotate Toggle Switch to the
" ï
stop.
22. TO ROTATE THE TURRET RIGHT: Press and
hold the Turret Rotate Toggle Switch to the
" ð " (right) position. Release the switch to
stop.
23. TO LEVEL THE PLATFORM (Platform is tilted
away from the jib): Press and hold the Platform
Leveling
" ñ " (up) position. To stop release the switch.
24. TO LEVEL THE PLATFORM (Platform is tilted
toward the jib): Press and hold the Platform
Leveling Toggle Switch to the " ò
position. To stop release the switch.
JUN. 1999
" (left) position. Release the switch to
Toggle Switch
SJKB-40-D, SJKB-40-D/F
to the
" (down)