Download Print this page

OLT FL Bevel Assembly Manual page 3

12x4 gardensaver shed

Advertisement

4. Trim & Miscellaneous Section
Bottom Skirting
4A: 5 - ¾" x 4 ½" x 45 ¼" - Side/Rear Bottom Skirting (FJ Bevel Siding)
4B: 3 - ½" x 4 ½" x 45 ¼" - Front Bottom Skirting
4BB: 3 - ½" x 1 ½" x 45 ¼" - Top Wall Trims (FJ Bevel Siding)
Filler Trim
4C: 4 - ½" x 2 ½" x 42" - Front Corner Filler Trims
4D: 4 - ¾" x 2 ½" x 38" - Rear Corner Filler Trims
Door System
4E: 2 - Aluminum Door Tracks (with brackets attached)
4F: 2 - 36" x 73" - Sliding Doors
4G: 2 - 1 ½" x 2 ½" x 61 1/8" - Lower Door Track
4HA: 3 - ½" x 4 ½" x 44 ¼" - Lower Door Track Cover
4IA: 3 - 1 ½" x 3 ½" x 3" - Sliding Door Track Stops
4J: 1 - ¾" x 3 ½" x 71 ½" - Interior Door Flange
4KA: 2 - 1 ½" x 3 ½" x 66 ½" - Track Overlay - Top
4KB: 2 - ¾" x 5 ½" x 67" - Track Overlay - Front
4KC: 2 - ½" x 3 ½" x 5 ½" - Track Overlay - Ends
4KD: 3 - ½" x 4 ¼" x 44 ¼" - Track Overlay - Sill (Bevel)
Outer Wall Trim
4L: 2 - ½" x 5 ½" x 88 ¾" - Front Corner Trims
4M: 2 - ½ x 2 ½" x 88 ¾" - Side Front Corner Trims
4N: 2 - ½" x 5 ½" x 78 ½" - Rear Corner Trims
4O: 2 - ½" x 2 ½" x 80" - Side Rear Corner Trims
4P: 2 - ½" x 2 ½" x 78 ½" - Rear Middle Trims
4Q: 2 - ½" x 2 ½" x 7 ½" - Front Middle Trims
Facia
4R: 2 - ½" x 5 ½" x 54 1/8" - Side Facia (Angle Cut Ends)
4S: 4 - ½" x 5 ½" x 50 ½" - Front and Rear Facia - Left/Right
4T: 2 - ½" x 5 ½" x 45 ½" - Front and Rear Facia - Center
4U: 5 - Trim Detail Plates (5 ½" high)
Windows
4W: 2 - Window Inserts 18 1/4"w x 23"h
4X: 2 - Window Trim Kits
1 - Top pc - 24 1/16" Length - Angle Cut Ends
3 - Side/Bottom pcs - 23" Length
Miscellaneous
4Y: 1 - 45 ¼" - Extra Piece of Bevel Wall Siding
- Use if side/rear wall panel siding is damaged or to shim floor or door.
4Z: 1 - 36" - Extra Piece of Lap Siding
- Use if front wall panel siding is damaged
Note: All Trim, Facia and Bottom Skiring pieces will be positioned rough face out when installed.
Toll Free 1-888-658-1658
Advice: Wood has a tendancy to split when
screwing near the ends of a board. To prevent
splitting, it is always recommended to pre-drill
pilot holes before screwing into these areas.
www.outdoorlivingtoday.com
Page 3
Steps
37-39
40-41
42-50
51-54
55-59
60-62
sales@outdoorlivingtoday.com

Advertisement

loading

This manual is also suitable for:

Ply roof