Table of Contents
Advertisement
CN8 Option, 49
CN8 Option Override Multiplication Gain, 181
CNU1/1A and CNU2/2A Pinout, 34
CNU2/2A Pinout, 34
Command (RS232/RS485) Menu, 52
Command Control Selections, 49
Command Mode Selection, 72
Command Source, 55
Commercial Power Switching Frequency Hold Time,
134
Commercial Power Wait Time, 134
Communication Baud Rate (logic), 184
Communication Error, 67, 188, 199
Communication Internal, 185
Communication Reference Adjust, 67
Communication Setting Parameters, 66
Communication Settings, 66
Communications Speed Frequency #1, 187
Communications Speed Frequency #2, 187
Communications Speed Reference #1, 186
Communications Speed Reference #2, 187
Compensation Coefficient for Iron Loss, 152
Configuration and Menu Options, 51
Connecting the ASD, 24
Connection Diagram, 38
Constant Vector Control, 152
Continued Stall Until Trip During Power Operation, 149
continuous splash screen, 34
Contrast (adjustment), 59
Control Board, 33
Control Power Undervoltage, 199
CPU Fault, 199
Crane/Hoist Load, 69
Cumulative Run Timer, 64
Cumulative Run Timer Alarm Setting, 172
Current Control Integral Gain, 137
Current Control Proportional Gain, 137
Current Differential Gain, 149
Current Vector Control, 152
Custom V/f Five-Point Setting #1 Frequency, 97
Custom V/f Five-Point Setting #1 Voltage, 98
Custom V/f Five-Point Setting #2 Frequency, 98
Custom V/f Five-Point Setting #2 Voltage, 98
Custom V/f Five-Point Setting #3 Frequency, 98
Custom V/f Five-Point Setting #3 Voltage, 98
Custom V/f Five-Point Setting #4 Frequency, 98
Custom V/f Five-Point Setting #4 Voltage, 99
Custom V/f Five-Point Setting #5 Frequency, 99
Custom V/f Five-Point Setting #5 Voltage, 99
Customer Support, 2
D
Date and time setting, 59
240
dbOn, 196
DC Braking, 63
DC Bus Undervoltage, 199
DC Fuse Open, 199
DC Injection Braking Current, 119
DC Injection Braking Start Frequency, 119
DC Injection Braking Time, 119
Dead Time Compensation, 70
Dead Time Compensation (Enable), 153
Dead-time Compensation Bias, 153
Decel #1 Time, 75
Decel #2 Time, 154
Decel #3 Time, 157
Decel #4 Time, 158
Deceleration Time Adjustment, 176
Default Setting Changes, 45
Default Term. Setting, 28
Derate Threshold frequency, 125
Direct Access, 59
Direct Access Parameter Information, 72
Direct Access Parameters/Numbers, 72
Direction (of motor rotation), 74
Discrete Input, 28
Discrete Output, 28
Display Units, 60
Display Units for Voltage and Current, 179
Disposal, 3
Down Key, 39
Drive Characteristics, 20
Driving Torque Limit #1, 147
Driving Torque Limit #2, 147
Driving Torque Limit #3, 148
Driving Torque Limit #4, 148
Drooping, 129
Drooping Control, 66
Drooping Gain, 129
Drooping Insensitive Torque Range, 130
Drooping Output Filter, 130
Drooping Reference, 131
Dynamic Braking, 63, 126
Dynamic Braking Enable, 126
Dynamic Braking Resistor Overcurrent, 199
Dynamic Braking Resistor Overload, 200
E
Earth Fault, 200
Earth Fault Alarm Level, 174
Earth Fault Alarm Time, 174
Earth Fault Trip Level, 175
Earth Fault Trip Time, 175
EEPROM Data Fault, 200
EEPROM Fault, 200
Electronic Gear Setting, 136
HX7+ ASD Installation and Operation Manual
Advertisement
Table of Contents
