Table of Contents EC DECLARATION OF CONFORMITY ....................4 Description of the machine ..........................5 Delivery Check .............................. 5 Instructions for unloading and final assembly ................... 5 Transport Brackets ............................. 5 Specifications ..............................6 Technical specifications ..........................6 Operating Instructions ........................... 6 Attachment ..............................
EC DECLARATION OF CONFORMITY in accordance with the EU Machinery Directive 2006/42/EC applicable as from December 29 2009: HE-VA ApS N. A. Christensensvej 34 DK-7900 Nykøbing Mors hereby confirms that the following machine has been manufactured in accordance with the Council Directive 2006/42/EC.
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Description of the machine The Tip-Roller is a 3-sectioned hydraulic, wheel mounted roller. Tip-Roller is to be used for packing the top soil, to maintain the content of moisture in it, and to eliminate not solid stones from the surface of the cultivated area.
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Specifications 3-section hydraulic wheel-mounted field roller with free movement in all sections. The roller is delivered with a working width of 4,5 - 5,4 - 6,3 meters, respectively, with 6 different ring types: cambridge- cam- star- 2D wave- cross-kill ring and rigid roller.
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Raise the support leg and place it in the transport fittings on top of the drawbar. Now fit the four hydraulic hoses. The hoses for the tip cylinder are provided with red tie strap. The hoses for the wing cylinder are provided with blue tie strap.
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 When rolling Speed: max. 10 km/h. When turning, drive in wide curves as far as possible. The turning should be performed no sharper, than all roller rings are still rotating forward. Only lower the wheels when making ready for transport position.
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Lubrication chart 2 nipples on wings pivot joints All ends on roller blocks, twice each season and after 10 hours wash Rod end of tip cylinder 1 nipple on folding cylinder 2 pc on pin for wings 30 hours 10 hours 3 nipples on pivot joint between rear drawbar and...
• Driver must be aware of, when operating that there are no persons at risk in the dangerous area. • He-Va cannot be held responsible for any falling accidents due to washing lubrication and other maintenance tasks • By the time tires will become tender and explosion danger can occur, when transporting or when controlling tire pressure •...
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Safety Instructions, regarding Hydraulic System 1. The highest allowable pressure is 225 bar. 2. It is recommended to mark the hydraulic connections between the implement and tractor, to avoid incorrect operation! 3.
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Markings on the machine Several markings are located at your machine, which contains safety regulations and other instructions to inform about correct operating. Please read these instructions carefully and make the driver aware about the markings and safety regulations in this Operating Instructions.
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Spare Part List, Roller Drawbar before May 2010 Back to the table of contents...
Page 15
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Pos. Art. no. Designation 4,5m 5,4m 6,3m 630751000 Front drawbar (Danish) 630876000 Front drawbar (German) 690141100 Support leg 3500 kg (Danish) 690141101 Support leg 3500 kg (German) 69516094A Pin ø16 0377400...
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Drawbar after May 2010 Back to the table of contents...
Page 17
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Pos. Art. no. Designation 4,5m 5,4m 6,3m 630757032 Front drawbar 630757097 Front drawbar for new parking device 690141100 Support leg 3500 kg 69516094A Pin ø16 690133005 Hairpin ø4 mm 690103075 M10x25 bolt 630771200...
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Wing Side Section Pos. Art. no. Designation 4,5m 5,4m 6,3m 630713011 Wing right 630723011 Wing right 630753007 Wing right 630713010 Wing left 630723010 Wing left 630753003 Wing left 630714000 Side section left 630724000 Side section left 630754000 Side section left...
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Wing and Side Section Ø620 rings after machin number: 342089 Pos. Art. no. Designation 4,5m 5,4m 630536410 Wing right 630546410 Wing right 630536400 Wing left 630546400 Wing left 630536510 Side section right 630546510...
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 690150099 Adjustment shim 20mm, complete set with bolts 690150063 Star ring Ø500, Center Ø135 690150064 Star ring Ø450 w/neck Ø60 690150065 Star ring Ø600, Center Ø135 690150066 Star ring Ø550 w/neck Ø60 690150112 Round plate Ø235 for mounting star rings Hydraulic Roller Back to the table of contents...
Page 25
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Pos. Art. No. Designation 4.5 m 5.4 m 6.3 m 690203001 Quick-coupling ½" male 690119202 Tie strap blue 690119203 Tie strap red 690203003 Screw-in straight GA10LK ½" 690201004 Hydraulic hose 1/4"...
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Spring-Board The Spring-Board requires a double-acting oil outlet on the tractor. The tine angle is hydraulically controlled from the driver's cap, with manual depth control. The tines work independently of each other, but can be coupled together by means of a transverse locking fittings (accessories), if a greater levelling output is required.
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Spring-Board, Center Section Back to the table of contents...
Page 28
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 4.5 m 5.4 m 6.3 m Pos. Art. No. Designation 633033020 Box section for tines 633043020 Box section for tines 633053020 Box section for tines 690109202 Plast plug 633031000 Suspension for centre section 635041000 Suspension for centre section Suspension for centre section...
Page 29
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Pos. Art. No. Designation 4.5 m 5.4 m 6,3 m 690201032 Hydraulic hose 1/4" L=1130 690201040 Hydraulic hose 1/4" L=1480 690201053 Hydraulic hose 1/4" L=1260 690201053 Hydraulic hose 1/4" L=1260 690201060 Hydraulic hose 1/4"...
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Spring-Board – Left Side Section Back to the table of contents...
Page 31
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 Pos. Art. No. Designation 4.5 m 5.4 m 6.3 m 633033010 Box section for tines (right) 633033030 Box section for tines (left) 633043010 Box section for tines (right) 633043030 Box section for tines (left) 635053010 Box section for tines (right) 635053030 Box section for tines (left)
Page 32
Tip Roller 4,5 - 5,4 - 6,3m (excl. 6,3 m w/620mm cambridge) 01-10-2021 690201006 Hydraulikslange 1/4" right side section L= 3800 mm 690201060 Hydraulikslange 1/4" left side section L= 3000 mm 690201060 Hydraulikslange 1/4" right side section L= 3000 mm 690201022 Hydraulikslange 1/4"...