Output 5/5 Screen; Pan/Tilt Screen - Panasonic AW-UE80WP Operating Instructions Manual

Camera menu items (continued)

Output 5/5 screen

O u t p u t 5/ 5
S t a t u s L a mp
E x t e r n a l Out put
O u t p u t 1
O u t p u t 2
R e t u r n
Status Lamp
[Enable, Disable]
[Disable] or [Enable] is set here for the status display lamp.
When you want the status display lamp to stay off while this unit is in
operation, set to [Disable].
<NOTE>
• Even when set to [Disable], the status display lamp may light
up when this unit is starting up, updating firmware, or trouble is
occurring.
External Output
Select the signal type output from the External Output signal lines
(Output1, Output2) of the RS‑422 connector. (→ page 17)
Output1 [Off, R‑Tally, G‑Tally]
Output2 [Off, R‑Tally, G‑Tally]
Off Signal is not output.
R-Tally The reception status of the red tally signal is output.
G-Tally The reception status of the green tally signal is output.
Return
Return to the previous menu level.

Pan/Tilt screen

E nable
Off
Off
Install Position
[Desktop, Hanging]
[Desktop] or [Hanging] is selected here as the method used to install
the unit.
Desktop
Hanging
<NOTE>
• When [Hanging] has been selected, the top, bottom, left and right
of the images will be reversed, and up/down/left/right control for
panning and tilting will also be reversed.
P/T Speed Mode [Normal(60deg/s), Fast1(90deg/s),
Fast2(180deg/s)]
Set the speed of pan/tilt operation.
Normal(60deg/s)
Fast1(90deg/s)
Fast2(180deg/s)
P/T Acceleration Setting
Displays the advanced setting screen for setting the acceleration
speed while starting/stopping a pan/tilt operation. (→ page 64)
Speed With Zoom Position [Off, On]
[Off] or [On] is set here for the function used to adjust the pan-tilt
adjustment speed in conjunction with the zoom magnification.
When [On] is set, the panning and tilting operations will become
slower in the zoom status.
This function has no effect during preset operations.
Focus Adjust With PTZ. [Off, On]
[Off] or [On] is set here for the function which compensates for out-of-
focusing when it occurs during panning, tilting or zooming operations.
When [Off] is set, adjust the focus as required after zooming or set
[Focus Mode] to [Auto].
This is only enabled when [Manual] has been selected as the [Focus
Mode] setting.
Privacy Mode [Off, On]
Sets Off/On the function for facing the camera to the rear when this
unit is switched to Standby mode.
Off
On
63
P a n / T i l t
I n s t a l l P o s i t i o n
P / T S p e e d M o d e N o r m a l ( 6 0 d e g / s )
P / T A c c e l e r a t i o n S e t t i n g
S p e e d W i t h Z o o m P o s i t i o n
F o c u s A d j u s t W i t h P T Z .
P r i v a c y M o d e
P o w e r O n P o s i t i o n
P r e s e t N u m b e r
R e t u r n
Stand-alone installation
Suspended installation
Pan/tilt operates at normal speed (maximum about
60° per second).
Pan/tilt operates at fast speed1 (maximum about 90°
per second).
Pan/tilt operates at fast speed2 (maximum about
180° per second).
Does not change the camera direction when the camera
is switched to Standby mode. (The camera remains in the
direction it was when the power was turned On)
Moves the camera to face toward the rear when the
camera is switched to Standby mode.
Moves the camera to the position specified in [Power On
Position] when the power is turned On again.
D e s k t o p
O n
O f f
O f f
S t a n d b y
0 0 1