Output 1/5 Screen - Panasonic AW-UE80WP Operating Instructions Manual

Camera menu items (continued)
z IP output
„
• When [IP] of [Tracking Data Output] on the [System 2/2] screen is
set to [On], the tracking data for Pan/Tilt/Zoom or other information is
synchronized with the Genlock signal and outputs UDP packets via IP.
• The tracking data is output in a format conforming to the free-d
protocol. The output specification (mode, command type, advanced
stored data) of this unit is equivalent to serial (RS-422) output.
<NOTE>
• When forwarding to more than one client, the timing of transmitting
the UDP packet to the second and subsequent client will always be
delayed relative to the Genlock signal.
(Approximately 200 to 300 μs delay will occur for each client. The
latency may be increased depending on the system status or the
network environment of the unit.)
• When [IP] is [On], video transmission via IP may be delayed or the
video may suffer frame loss.
We recommend setting [IP] to [Off] to avoid the delay or frame loss
due to the video transmission via IP.
• In the following cases, the tracking data output may be delayed or the
value may not be updated.
- When performing video transmission via IP (M-JPEG/H.264/H.265/
RTMP/RTMPS/NDI/NDI|HX/SRT)
- When opening the web screen (live screen [Live] or the web setting
screen [Setup])
- While viewing the OSD menu
- While recalling the preset value during an ongoing preset recall
- When executing AWB/ABB
- When a red or a green tally signal input has been changed between
Off and On
- When deleting a preset memory
- When an output image is flipped (turned upside down or left-right
reversed)
- After switching [Scene]
- After switching [Iris Mode]
- After switching [Super Gain]
- After switching [White Balance Mode]
- After switching [Gamma Mode]
- After switching [Matrix Type]
- After switching [Focus Mode]
- After switching [Zoom Mode]
- After switching [Max Digital Zoom]
- After switching [Digital Extender]
- After switching [Fan]
- After switching [OSD Mix]
- After switching [Tally]
- After switching [Install Position]
- After switching [Preset Speed Unit]
- When executing [Initialize] of [Maintenance]

Output 1/5 screen

O u t p u t 1 / 5
3 G S D I
F o r m a t
3 G S D I O u t
H D M I
F o r m a t
V i d e o S a m p l i n g
R e t u r n
3G SDI
Make the settings for output from the 3G SDI OUT connector.
Format
Set the output format.
The following format settings are possible depending on the [Format]
setting in the [System 1/2] screen.
Frequency System Format
59.94Hz 2160/59.94p
2160/29.97p
1080/59.94p
1080/59.94i
1080/29.97p
1080/29.97PsF
1080/23.98p(59.94i)
720/59.94p
50Hz 2160/50p
2160/25p
1080/50p
1080/50i
1080/25p
1080/25PsF
24Hz 2160/24p
1080/24p
23.98Hz 2160/23.98p
1080/23.98p
1080/23.98PsF
* 1
It denotes "1080/23.98p over 59.94i".
3G SDI Out [LevelA, LevelB]
When [Format] (3G SDI) is [1080/59.94p] or [1080/50p], select the
format for outputting 3G SDI signals.
LevelA Level A format
LevelB Level B format
<NOTE>
• [3G SDI Out] cannot be changed if [Format] (3G SDI) is other than
[1080/59.94p] or [1080/50p].
60
1 0 8 0 / 5 9 . 9 4 p
L e v e l A
2 1 6 0 / 2 9 . 9 7 p
4 : 2 : 2 / 1 0 b i t
Format (3G SDI)
1080/59.94p
1080/59.94i
1080/29.97p
1080/59.94p
1080/59.94i
1080/59.94i
1080/29.97p
1080/29.97PsF
1080/23.98p(59.94i)
1
*
720/59.94p
1080/50p
1080/50i
1080/25p
1080/50p
1080/50i
1080/50i
1080/25p
1080/25PsF
720/50p 720/50p
1080/24p
1080/24p
1080/23.98p
1080/23.98p
1080/23.98PsF
1
*