Display Of The Drive; Panel Operation - Emerson EV2000 Series User Manual

40 Chapter 4 Operation Instructions
Table 4-2 Functions of status indicators
Indicator
Operating status
indicator
Control mode
indicator

4.2.4 Display of the Drive

EV2000 operation panel can display the parameters in
stopping, operating, editing and alarming state.
1. Parameters displayed in stopping status
When the drive stops operation, the panel will display
the status parameters in stopping status, as shown in
Fig. 4-4b. The unit indicator on the top right of the panel
indicates the unit of the parameter.
Other parameters can be displayed by pressing
(see F8.03).
2. Parameters displayed in operating status
When the drive receives operating command, it starts
running and its panel will display the status parameters
in operating status, as shown in Fig.c of Fig. 4-4. The
unit indicator at right indicates the unit of the parameter.
Other parameters can be displayed by pressing
(see F8.01 and F8.02).
PARAMETER PARAMETER UNIT UNIT
PARAMETER PARAMETER
HZ HZ
r/min r/min
% %
A A
m/s m/s
V V
EV2000
EV2000
ENYDRIVE
ENYDRIVE
MENU ENTER PANEL
ESC DATA REMOTE
JOG
STOP STOP
STOP
RUN RUN
RUN
RESET RESET
RESET
Fig. a
Initialize at power on, Stopping state, Stopping
all LED turns on information is displayed ;
RUN indicator turns off
Fig. 4-4 Displayed during initialization, STOP, operation
3. Alarm information
When the drive detects a fault signal, the panel will
display the fault code. The code will flash to catch your
attention as shown in Fig. 4-5;
Reference frequency can be viewed by pressing the
key in stopping status. Fault information can be queried
by pressing MENU/ESC key. The drive can be reset by
pressing the STOP/RESET key, or sending the reset
Display Current status of the
status drive
Off Stopping status
On Operating status
On Panel control status
Terminal control
Off
status
Serial port control
Flash
status
PARAMETER PARAMETER
UNIT UNIT
HZ HZ
r/min r/min
% %
A A
m/s m/s
V V
Freq. precompensation
Preset frequency
Common run Forward
Stop
ENTER ENTER PANEL PANEL PANEL PANEL
MENU MENU MENU MENU
MENU
REMOTE
ESC DATA ESC
JOG
STOP STOP STOP STOP
RUN RUN RUN RUN RUN RUN
RUN RUN
RESET RESET RESET
RESET
Fig. c
Fig. b
Running state, running
information is displayed;
RUN indicator turns on
EV2000 Series Universal Variable Speed Drive User Manual
commands via the control terminal X2 or serial port. The
fault code will not disappear until the fault is cleared.
4. Parameter configuration
When the drive is in stopping, operating or alarming
state, pressing MENU/ESC can enter configuring status,.
Configuring status can be displayed in 3-level menu,
they are: parameter group → pparameter → parameter
value. You can enter the sub-menus by pressing
ENTER/DATA. In parameter value menu, press
ENTER/DATA to save the settings, and press
key
MENU/ESC to exit the menu.

4.2.5 Panel Operation

1. Viewing Parameters
To view the parameters, press
that can be displayed are different depending on the
operation state (STOP, operating) and the settings of
key
F8.01~F8.03)
2. Parameter Setup
UNIT UNIT
HZ HZ
Let's look at an example of how to set parameters.
r/min r/min
% %
A A
m/s m/s
V V
Suppose you want to change the setting of F3.13 from
5.00Hz to 6.50Hz.
1. Press MENU/ESC key to enter programming state,
ENTER PANEL
the LED displays F0.
REMOTE
DATA
JOG 2. Press ▲ key until "F3" is displayed.
STOP STOP STOP STOP
RESET RESET RESET
3. Press ENTER/DATA key, you will see F3.00. Press
RESET
▲ key until "F3.13" is displayed.
4. Press ENTER/DATA key, you will see "05.00".
5. Press
Press ▲ key once, to change it to "6". Press
move the cursor to the next digit (from left to right) and
press ▲ key until the figure "5" appear.
6. Press ENTER/DATA key to save the modification and
you will see the next parameter F3.14.
7. Press MENU/ESC key to exit the programming state.
PARAMETER
Input Phase Failure
Pls Check
Fig. 4-5 Alarm displaying status
key. The parameters
key, to move the cursor to the digit "5".
UNIT
Hz
HZ
r/min
A %
m/s
V
key, to