Stop (Push) Side Mounting; Stop (Push) Side Installation - Assa Abloy Norton 5700 Series Installation And Instruction Manual

1/2
(13)
3/8
(10)
C L Hinge or Pivot
Please verify desired mounting
requires Stop (Push) Side
application as shown on this
template.
1-1/2" (38mm)
Min. Frame Face
Frame Reveal*
Note: Door must be visible by person operating activation switch(es)
Step 1: Determine hand of door from illustration on upper right of this
page.
Step 2: Using template above locate and prepare holes in the frame &
door:
Frame
A. Prepare six (6) holes for 1/4-20 machine screws or
14 x 2-3/4" (70mm) wood screws. Blind rivet nuts (by others) are
suggested for unreinforced hollow metal frames or for aluminum
frames.
B. Concealed Wired Units Only: Two (2) 7/8" (22mm) diameter
holes for conduit, for power input and for switch/sensor wires.
NOTE: On new construction these holes will generally be drilled
by the frame supplier at their shop or at the time the frame is
installed in the wall.
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2010, 2013 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
2. Stop (Push) Side Mounting Instructions
B
14-3/16
(360)
13-13/16
(351)
12-15/16
(329)
11-11/16
(297)
1-1/4
11/16
(32)
(17.5)
7/8
(22)
(Conduit Holes -
2 Places)
A
Door Opening
Dim "A"
Angle
Up to 110° 12 (305)
111° to 170° 9-1/2 (241) 13-1/4 (337)
5-1/4" (133mm)
2A. Installation Sequence
Left Hand Door
open to 110° shown.
13-7/16
(341)
1/4-20 Machine Screws
or No. 14 Wood Screws
7-9/16
(192)
1-11/16
(43)
3/8
1-3/4
Dia.
(19)
(44)
Sex Nuts
Dim "B"
(2 Places)
15-3/4 (400)
Min. Ceiling
Clearance
1-3/4" (44mm) Min.
Door Thickness
2-1/4" (57mm) Max.
Door
C. Prepare two (2) holes for 3/8" diameter sex nuts. Standard units
are supplied with sex nuts and screws for 1-3/4" (44mm) thick
door. Sex nuts and screws for other door thicknesses are
available to order.
Step 3: Remove cover from the unit and set cover & cover screws
aside.
No.
Step 4: Mount unit to door frame. Select A or B below.
A. Concealed Wired Units Only:
backplate. Fasten unit to door frame (six screws).
B. Surface Wired Units Only:
Mount conduit bracket (found in screw pack) to unit backplate
with two screws provided. Connect wiring conduit to bracket.
Page 6
13-13/16
(351)
(6 Places)
Frame
Stop/Soffit
Notes:
• All dimensions are given in inches (mm).
• Thickness recommended for reinforcements in
hollow metal doors and frames is charted at the
left of this page.
• Do not scale drawing.
• Left hand door shown.
• This template information based upon use of 5"
(127mm) maximum width butt hinges or 3/4"
(19mm) offset pivots. A separate template will
be supplied for other conditions.
• Maximum frame reveal is 7" (178mm) for this
application.
• Conduit hole nearest to hinge is suggested for
120 VAC power input.
*For frame reveals less than 3" (76mm) the
arm adjusting rod can be field cut to a
length of 9-1/2" (241mm) measured from
centerline of connecting link bushing
assembly.
Connect conduit to frame side of
Fasten unit to door frame (six screws).
ASSA ABLOY
Left Right
Hand Hand
Door Door
5-1/4"
Min.
Clearance
5/8
Frame
Stop
(15.9)
Rabbet
80-9357-0001-020 (09-13)