Stop (Push) Side Mounting; Stop (Push) Side Installation - Assa Abloy Norton LEO 5700 Series Installation And Instruction Manual

15 (381)
Max. Distance
for Placement
of Power Input
Receptical
(shaded region)
1/2
(13)
3/8
(10)
C L Hinge or Pivot
1-1/2" (38mm)
Min. Frame Face
Frame Reveal*
Note: Door must be visible by person operating activation switch(es)
Step 1: Determine hand of door from illustration on upper right of this
page.
Step 2: Using template above locate and prepare holes in the frame &
door:
Frame
A. Prepare six (6) holes for 1/4-20 machine screws or No. 14 x 2-3/4"
(70mm) wood screws. Blind rivet nuts (by others) are suggested
for unreinforced hollow metal frames or for aluminum frames.
B. Concealed Class 2 Low Voltage Only: One (1) 7/8" (22mm)
diameter holes for conduit, for power input and for switch/sensor
wires.
NOTE: On new construction these holes will generally be drilled
by the frame supplier at their shop or at the time the frame is
installed in the wall.
Page 6
2. Stop (Push) Side Mounting Instructions
B
14-3/16
(360)
13-13/16
(351)
12-15/16
(329)
11/16
(17.5)
7/8
(22)
(Class 2
Wiring Only)
A
Please verify desired mounting
requires Stop (Push) Side
application as shown on this
template.
Door Opening
Angle
Up to 110°
111° to 170°
5-1/4" (133mm)
Min. Ceiling
Clearance
1-3/4" (44mm) Min.
2-1/4" (57mm) Max.
2A. Installation Sequence
Left Hand Door
open to 110° shown.
13-13/16
13-7/16
(341)
1/4-20 Machine Screws
or No. 14 Wood Screws
7-9/16
(192)
1-11/16
(43)
3/8
1-3/4
Dia.
(19)
(44)
Sex Nuts
(2 Places)
Dim "A" Dim "B"
12 (305) 15-3/4 (400)
9-1/2 (241) 13-1/4 (337)
Door Thickness
Door
C. Prepare two (2) holes for 3/8" diameter sex nuts. Standard units
are supplied with sex nuts and screws for 1-3/4" (44mm) thick
door. Sex nuts and screws for other door thicknesses are
available to order.
Step 3: Remove cover from the unit and set cover & cover screws
aside.
Step 4: Mount unit to door frame. Select A or B below.
A. Concealed Class 2 Low Voltage Only:
side of backplate. Fasten unit to door frame (six screws).
B. Surface Class 2 Low Voltage Only:
screws). Mount conduit bracket (found in screw pack) to unit
backplate with two screws provided. Connect wiring conduit to
bracket.
(351)
(6 Places)
Frame
Frame
Stop/Soffit Rabbet
Notes:
• All dimensions are given in inches (mm).
• Thickness recommended for reinforcements in
hollow metal doors and frames is charted at the
left of this page.
• Do not scale drawing.
• Left hand door shown.
• This template information based upon use of 5"
(127mm) maximum width butt hinges or 3/4"
(19mm) offset pivots. A separate template will
be supplied for other conditions.
• Maximum frame reveal is 7" (178mm) for this
application.
• Conduit hole is Class 2 low voltage wiring
ONLY.
!Due to the risk of the Power Cord becoming
entrapped in moving parts of the operator, door,
or system, the Power Cord must be kept clear of
*For frame reveals less than 3" (76mm) the
arm adjusting rod can be field cut to a
length of 9-1/2" (241mm) measured from
centerline of connecting link bushing
assembly.
Fasten unit to door frame (six
80-9357-0002-020 (01-12)
Left Right
Hand Hand
Door Door
5-1/4"
Min.
Clearance
5/8
Stop
(15.9)
Connect conduit to frame