Canon imageRUNNER 2545 Series Service Manual page 202

Ecode Detail Item
Code
E719 0002 Title Erroneous communication with Coin Vendor (serial
communication)
Description -
Remedy -
E736 0000 Title Erroneous communication between CCU and controller.
Description -
Remedy -
E744 0001 Title Mismatched version between the language file and the
Bootable
Description -
Remedy -
E744 0002 Title Oversized language file in HDD
Description -
Remedy -
E744 0003 Title Mismatched version between the language file and the
Bootable
Description -
Remedy -
E744 0004 Title Language file reading error
Description -
Remedy -
E804 0000 Title Failure of the Power Supply Cooloing Fan (FAN6)
Description When lock signal is detected for 5 sec while the Power
Supply Cooloing Fan (FAN6) is stopped.
* The same condition is detected after the error retry is
performed.
Remedy 1.Disconnect and then connect the connector (J205) on the
DC Controller PCB (PCB4).
2.Replace the Power Supply Cooloing Fan (FAN6).
3.Replace the DC Controller PCB (PCB4).
E804 0001 Title Unstable rotation of the Power Supply Cooloing Fan (FAN6)
Description When lock signal failed to be detected for 5 sec while the
Power Supply Cooloing Fan (FAN6) is driven.
* The same condition is detected after the error retry is
performed.
Remedy 1.Disconnect and then connect the connector (J205) on the
DC Controller PCB (PCB4).
2.Replace the Power Supply Cooloing Fan (FAN6).
3.Replace the DC Controller PCB (PCB4).
7
Description
7
Ecode Detail Item
Code
E805 0000 Title Failure of the Exhaust Fan (Rear) (FAN3)
Description "When lock signal is detected for 5 sec while the Exhaust Fan
(Rear) (FAN3) is stopped.
* The same condition is detected after the error retry is
performed."
Remedy 1.Disconnect and then connect the connector (J206) on the
DC Controller PCB (PCB4).
2.Replace the Exhaust Fan (Rear) (FAN3).
3.Replace the DC Controller PCB (PCB4).
E805 0001 Title Unstable rotation of the Exhaust Fan (Rear) (FAN3) or
Finisher Fan 1 (M8) or Finisher Fan 2 (M9)
Description 1.When lock signal failed to be detected for 5 sec while the
Exhaust Fan (Rear) (FAN3) is driven.
2.When lock signal failed to be detected for 5 sec while the
Finisher Fan 1 (M8) is driven.
3.When lock signal failed to be detected for 5 sec while the
Finisher Fan 2 (M9) is driven.
* The same condition is detected after the error retry is
performed.
Remedy 1.Disconnect and then connect the connector (J206) on the
DC Controller PCB (PCB4).
2.Replace the Exhaust Fan (Rear) (FAN3).
3.Replace the Finisher Fan 1 (M8).
4.Replace the Finisher Fan 2 (M9).
5.Replace the DC Controller PCB (PCB4).
E805 0002 Title Failure of the Exhaust Fan (Front) (FAN4)
Description When lock signal is detected for 5 sec while the Exhaust Fan
(Front) (FAN4) is stopped.
* The same condition is detected after the error retry is
performed.
Remedy 1.Disconnect and then connect the connector (J206) on the
DC Controller PCB (PCB4).
2.Replace the Exhaust Fan (Front) (FAN4).
3.Replace the DC Controller PCB (PCB4).
E805 0003 Title Unstable rotation of the Exhaust Fan (Front) (FAN4)
Description When lock signal failed to be detected for 5 sec while the
Exhaust Fan (Front) (FAN4) is driven.
* The same condition is detected after the error retry is
performed.
Remedy 1.Disconnect and then connect the connector (J206) on the
DC Controller PCB (PCB4).
2.Replace the Exhaust Fan (Front) (FAN4).
3.Replace the DC Controller PCB (PCB4).
7-8
Description
T-7-2
7-8