Canon imageRUNNER 2545 Series Service Manual page 198

Ecode Detail Item
Code
E014 0001 Title Unstable rotation of the Fixing Motor (M2)
Description Detection is executed every 100 msec after the start of motor
rotation; however, the drive detection signal is absent for 2
sec.
Remedy 1.Replace the Fixing Motor (M2).
2.Replace the DC Controller PCB (PCB4).
E014 0002 Title Unstable rotation of the Fixing Motor (M2)
Description During motor rotation, detection is executed every 100 msec;
however, the drive signal is absent 5 times in sequence.
Remedy 1.Replace the Fixing Motor (M2).
2.Replace the DC Controller PCB (PCB4).
E019 0000 Title Error in Waste Toner Sensor (S17)
Description Warning when the sensor goes on for 2000 consecutive
sheets, and error when the sensor goes on for 100
consecutive sheets.
* Error occurs after the delivery if a paper in passage exists.
Remedy 1.Replace the Waste Toner Sensor (S17).
2.Replace the DC Controller PCB (PCB4).
E020 0000 Title The path between the sub hopper and the developing
assembly is clogged with toner.
Description The Developing Assembly Toner Sensor (TS1) detects the
absence of toner,while the Sub Hopper Toner Sensor (TS2)
detects the presence of toner.
With the Developing Cylinder Clutch (CL3) turned on,
the hopper feedscrew motor (M7) is rotated for 1 sec
intermittently 194 times; still, theDeveloping Assembly Toner
Sensor (TS1) does not detect the presence of toner.
* Error occurs after the delivery if a paper in passage exists.
Remedy 1.Check the rotation of hopper motor gear. (If rotating, false
detection by the sensor is doubted. Feed the toner to the
developing unit in service mode: CLEAR>ENGIN>TNRINST.)
2.Replace the Developing Assembly Toner Sensor (TS1).
3.Replace the Sub Hopper Toner Sensor (TS2).
4.Replace the DC Controller PCB (PCB4).
E024 0000 Title The connector (J207) of Developing Assembly Toner Sensor
(TS1) is disconnected.
Description The Developing Assembly Toner Sensor (TS1) connection
detection signal is absent for 100 msec 10 times in sequence.
* Error occurs after the delivery if a paper in passage exists.
Remedy 1.Check connection of the Connector (J207).
2.Replace the Developing Assembly Toner Sensor (TS1).
3.Replace the DC Controller PCB (PCB4).
7
Description
7
Ecode Detail Item
Code
E024 0001 Title The Developing Assembly Toner Sensor (TS1) is
disconnected.
Description <At LOW SPEED>
- The developing assembly toner sensor (TS1) ON counter
is checked every 2.5 seconds, and the counter increments
1 count every 25 times when the sensor goes on, and 300
counts are reached.
<At HIGH SPEED>
- The developing assembly toner sensor (TS1) ON counter
is checked every 1.5 seconds, and the counter increments
1 count every 15 times when the sensor goes on, and 300
counts are reached.
Remedy 1.Check connection of the Connector (J207).
2.Correct the cable.
3.Replace the Developing Assembly Toner Sensor (TS1).
E025 0000 Title The connector (J207) of Sub Hopper Toner Sensor (TS2) is
disconnected.
Description The Sub Hopper Toner Sensor (TS2) connection detection
signal is absent for 100 msec 10 times in sequence.
* Error occurs after the delivery if a paper in passage exists.
Remedy 1.Check connection of the Connector (J207).
2.Replace the Sub Hopper Toner Sensor (TS2).
3.Replace the DC Controller PCB (PCB4).
E025 0001 Title Failure of the Bottle Motor (M6)
Description The bottle motor (M6) is unlocked when it goes on for 12
consecutive times at 0.1 sec. intervals.
* Error occurs after the delivery if a paper in passage exists.
Remedy 1.Replace the Bottle Motor (M6).
2.Replace the DC Controller PCB (PCB4).
E110 0001 Title Failure of the Scanner Motor (M21)
Description The Scanner Motor (M21) speed lock signal does not indicate
a locked state a specific period of time after the Scanner
Motor (M21) has been started.
* The same condition is detected after the error retry is
performed.
Remedy 1.Check the cable.
2.Replace the Laser Scanner Unit.
3.Replace the DC Controller PCB (PCB4).
7-4
Description
7-4