NTI ENVIROMUX Series Installation And Operation Manual
Automatic voice dialer system
Hide thumbs
Also See for ENVIROMUX Series:
- Installation and operation manual (150 pages) ,
- Manual (59 pages) ,
- Instruction manual (19 pages)
Related Manuals for NTI ENVIROMUX Series
Summary of Contents for NTI ENVIROMUX Series
- Page 1 ® ENVIROMUX Series E-AVDS-CELC-V3 Automatic Voice Dialer System Installation and Operation Manual MAN402 Rev Date 05/13/21...
- Page 2 TRADEMARK ENVIROMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries. COPYRIGHT Copyright © 2021 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Introduction..................................1 Materials ..................................1 Mounting and Wiring ............................... 2 Installation ..................................3 Programming ................................... 6 Technical Specifications..............................10 Warranty Information..............................10... -
Page 4: Introduction
NTI Automatic Voice Dialer INTRODUCTION The E-AVDS-CELC-V3 is an automatic voice dialer system that when used in conjunction with the ENVIROMUX Enterprise Environment Monitoring System can call up to 6 pre-programmed numbers and provide a recorded message communicating the status of a sensor. When the SYSTEM recognizes an alarm it triggers the auto dialer. The telephone auto dialer uses a telephone line to dial the pre-programmed telephone number. -
Page 5: Mounting And Wiring
NTI Automatic Voice Dialer MOUNTING AND WIRING The E-AVDS-CELC-V3 can be wired to be powered directly by most ENVIROMUX model monitoring systems. A terminal block is located inside the case, accessed by removing the screw at the bottom of the unit. -
Page 6: Installation
NTI Automatic Voice Dialer INSTALLATION The dialer must be connected to a +12 V power supply. Standard copper wiring should be used. Connect the alarm cable wiring starting with +12V and 0V connections from the ENVIROMUX and wire them into the +12V and 0V terminals of the Dialer. If the ENVIROMUX is not being used as the power supply for the Dialer then a common 0V connection between the control panel and dialer must be made. - Page 7 NTI Automatic Voice Dialer...
- Page 8 NTI Automatic Voice Dialer...
-
Page 9: Programming
NTI Automatic Voice Dialer PROGRAMMING The dialer is on standby when only the green power "ON" LED is illuminated. To make changes to the configuration, you must first enter the four-digit password. The factory set password is 8888 → →... - Page 10 NTI Automatic Voice Dialer 2.1 Playback of Message To play any of the messages previously recorded: b) Press ENTER c) Press the number of the message (0-3, where 0 corresponds to the location message). d) Key in 1=Playback 3. Dialing mode The dialer can be programmed to call a specific number when each alarm occurs, or it can be programmed to call all programmed numbers.
- Page 11 NTI Automatic Voice Dialer 5. Trigger Modes The auto dialer has three programmable inputs, and the user can change the trigger mode of the input. 0=Edge Trigger-When the trigger signal is detected the dialer will start dialing. The dialer will make a circular call to all numbers three times even if the trigger signal is stopped 1=Level Trigger-When the trigger signal is detected the dialer will start dialing.
- Page 12 NTI Automatic Voice Dialer 11. Relay Activation Time The dialer has one relay controlled by the Relay Control Input (IN). The relay activation time can be programmed from 1 to 255 seconds. The factory setting for relay activation time is 10 seconds.
-
Page 13: Technical Specifications
NTI Automatic Voice Dialer TECHNICAL SPECIFICATIONS Max. # of stored phone numbers Max. # of digits per phone number Recording (message) 12 Seconds for location message duration 6 seconds for each of 3 alarm (input) messages Input Voltage 10 to 15 VDC Max.