Mitsubishi Electric MELSERVO J5 Series User Manual page 13

Model: MR-J5-
Structure (IP rating)
*2
Close mounting 3-phase power supply input
1-phase power supply input
Mass [kg]
*1 This value is applicable when all I/O signals are used. Reducing the number of I/O points decreases the current capacity.
*2 If closely mounting the servo amplifiers, operate them at an ambient temperature of 0 ˚C to 45 ˚C or at 75 % or less of the effective load
ratio.
*3 This current value is applicable when a 3-phase power supply is used.
*4 If using 1-phase power supply in combination with the servo motor of 750 W or higher, operate the servo amplifier at 75 % or less of the
effective load ratio.
*5 The command communication cycle depends on the controller specifications and the number of the connected axes.
*6 This does not apply to connectors.
*7 The communication cycles of 31.25 μs and 62.5 μs can be used by servo amplifiers with firmware version A6 or later.
400 V class
Model: MR-J5-
Output Voltage
Rated current [A]
Main circuit power Voltage/
supply input Frequency
Rated current [A]
Permissible
voltage
fluctuation
Permissible frequency
fluctuation
Power supply capacity [kVA]
Inrush current [A]
Control circuit power Voltage/
supply input Frequency
Rated current [A]
Permissible
voltage
fluctuation
Permissible frequency
fluctuation
Power consumption [W]
Inrush current [A]
Interface power supply Voltage
Current capacity [A]
Control method
Dynamic brake
CC-Link IE TSN Communication cycle
Authentication class
Communication USB
function
Encoder output pulses
Analog monitor
Fully closed loop control
Scale measurement function
Load-side encoder MR-J5-_G4
interface
MR-J5-_G4-RJ
10G 20G 40G
Natural cooling, open (IP20)
Possible
Possible
0.8
60G4
3-phase 0 V AC to 480 V AC
1.6
At AC input 3-phase 380 V AC to 480 V AC, 50 Hz/60 Hz
1.4
At AC input 3-phase 323 V AC to 528 V AC
Within ±5 %
Refer to "Power supply capacity and generated loss" in the following manual.
MR-J5 User's Manual (Hardware)
Refer to "Inrush currents at power-on of main circuit and control circuit" in the following manual.
MR-J5 User's Manual (Hardware)
At AC input 1-phase 380 V AC to 480 V AC, 50 Hz/60 Hz
0.1
At AC input 1-phase 323 V AC to 528 V AC
Within ±5 %
30
Refer to "Inrush currents at power-on of main circuit and control circuit" in the following manual.
MR-J5 User's Manual (Hardware)
24 V DC ±10 %
0.3 (including CN8 connector signals)
Sine-wave PWM control, current control method
Built-in
*2
31.25 μs, 62.5 μs, 125 μs, 250 μs, 500 μs, 1 ms, 2 ms, 4 ms, 8 ms
Class B
Connection to a personal computer or other devices (MR Configurator2-compatible)
Compatible (A/B/Z-phase pulse)
Two channels
Supported
Supported
Mitsubishi Electric high-speed serial communication
Mitsubishi Electric high-speed serial communication/A/B/Z-phase differential input signal
60G 70G 100G 200G
Force cooling, open (IP20)
Impossible
1.0 1.4 2.2
100G4 200G4
2.8 5.5
2.5 5.1
*1
1.4 Servo amplifier standard specifications
350G 500G 700G
Force cooling,
*6
open (IP20)

3.7 6.2
350G4
8.6
7.9
1 SPECIFICATIONS
11
1