Altronix Maximal Series Installation Manual
  1. Manuals
  2. Brands
  3. Altronix Manuals
  4. Controller
  5. Maximal series
  6. Installation manual
Altronix Maximal Series Installation Manual

Altronix Maximal Series Installation Manual

Access power controller
Hide thumbs Also See for Maximal Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Series
Access Power Controllers
Installation Guide
Models Include:
Maximal3D
- 12VDC @ 5 amp or 24VDC @ 5.4 amp.
- Sixteen (16) PTC protected Class 2 Rated power-limited outputs.
Maximal5D
- 12VDC @ 9 amp.
- Sixteen (16) PTC protected Class 2 Rated power-limited outputs.
Maximal7D
- 24VDC @ 9.4 amp.
- Sixteen (16) PTC protected Class 2 Rated power-limited outputs.
Altronix Corp.
140 58th St. Brooklyn, NY
More than just power.
TM
Rev. SCB110912

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Maximal Series and is the answer not in the manual?

Questions and answers

Related Manuals for Altronix Maximal Series

Summary of Contents for Altronix Maximal Series

  • Page 1 - 12VDC @ 9 amp. - Sixteen (16) PTC protected Class 2 Rated power-limited outputs. Maximal7D - 24VDC @ 9.4 amp. - Sixteen (16) PTC protected Class 2 Rated power-limited outputs. Altronix Corp. 140 58th St. Brooklyn, NY More than just power. Rev. SCB110912...

  • Page 2: Table Of Contents

    Table of Contents: MaximalD Series Overview ..................... 3 MaximalD Series Configuration Chart ................3 MaximalD Series Features ....................3 MaximalD Installation Instructions ................4-5 Maintenance ........................5 Power Supply Board LED Diagnostics ................5 Access Power Controller LED Diagnostics ..............6 Power Supply Board Terminal Identification ..............

  • Page 3: Maximald Series Overview

    Maximal5D 12VDC @ 9 amp 2 amp 2.6 amp 5A/250V 15A/32V Evaluated to CSA Standard C22.2 No.205-M1983 Altronix Corp. 140 58th St. Brooklyn, NY Maximal7D 24VDC @ 9.4 amp California State Fire 2 amp 4.4 amp 5A/250V 15A/32V Marshal Approved MaximalD Series Features: •...

  • Page 4: Maximald Installation Instructions

    MaximalD Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. Power Supply Board LED Diagnostics (pg. 5) Access Power Controller LED Diagnostics (pg.

  • Page 5: Maintenance

    9. FACP Dry form “C” output (Fig. 2a, pg. 8): FACP form “C” contacts can be use to trigger reporting or signaling devices. These contact switch upon a fire alarm input trigger to the ACM8CB boards. 10. Stand-by Battery Connections (Figs. 3-7, pgs. 9-13): For Access Control applications batteries are optional.

  • Page 6: Access Power Controller Led Diagnostics

    Power Supply Board LED Diagnostics: Red (Bat) Battery Status Normal operating condition. Battery fail/low battery. Access Power Controller LED Diagnostics: LED 1- LED 8 (Red) Output relay(s) energized. Output relay(s) de-energized. Trg (Green) FACP input triggered (alarm condition). FACP normal (non-alarm condition). Power Supply Board Terminal Identification: Terminal Function/Description...

  • Page 7: Power Supply Board Stand-By Battery Specifications

    Power Supply Board Stand-by Battery Specifications: Altronix 20 Min. 24 hr. of Power Supply Board Battery 4 hr. of Backup Model: of Backup Backup AL600ULXB 12VDC/40AH* 5.0 amp Maximal3D (Refer to Fig. 1a, pg. 7 for Switch 24VDC/40AH* 5.4 amp 0.7 amp...

  • Page 8: Access Power Controller Typical Application Diagram

    Access Power Controller Typical Application Diagram (for each ACM8CB): Fig. 2 Fig. 2a KEYPAD ACCESS CONTROL PANEL PUSH FACP BUTTON FACP Dry Form "C" (Fire Output OUTPUT Alarm RELAY Control Panel) IN GND IN GND IN GND IN GND IN GND IN GND IN GND IN GND...

  • Page 9: Maximal3D And Maximal5D Battery Hookup And Tamper Switch Installation

    Fig. 3 Maximal3D Tamper Switch Maximal5D Wire Strap (from Enclosure Power Supply Board to Door) BAT FAIL AC FAIL NO C NC NO C NC 115VAC Input Line Neutral 60 Hz. Earth Ground *12VDC operation: For 12VDC operation only a single battery is needed. Connect red battery lead to terminal marked [+ BAT] and to the [positive (+)] terminal of the...

  • Page 10: Maximal7D Battery Hookup And Tamper Switch Installation

    Fig. 4 Maximal7D Tamper Switch Power Supply Board BAT FAIL AC FAIL NC C NO NC C NO AC DELAY 115VAC Input Line Neutral 60 Hz. Earth Ground 12VDC Rechargeable 12VDC Rechargeable Battery** Battery** (Optional) (Optional) **24VDC operation: Connect two (2) 12VDC batteries in series Fig.

  • Page 11: Nec Power-Limited Wiring Requirements For Maximal3D

    NEC Power-Limited Wiring Requirements for Maximal3D: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below.

  • Page 12: Nec Power-Limited Wiring Requirements For Maximal5D

    NEC Power-Limited Wiring Requirements for Maximal5D: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below.

  • Page 13: Nec Power-Limited Wiring Requirements For Maximal7D

    NEC Power-Limited Wiring Requirements for Maximal7D: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below.

  • Page 14: Facp Hook-Up Diagrams

    FACP Hook-up Diagrams: Fig. 8 Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm condition): JUMPER J3 FACP SIGNAL CIRCUIT OUTPUT EOL FROM FACP SIGNAL OUTPUT CIRCUIT Fig. 9 Normally Open - Non-Latching FACP Fig. 10 Normally Open FACP Latching trigger input trigger input: with reset: (This output has not been evaluated by UL)

  • Page 15: Enclosure Dimensions

    Enclosure Dimensions (H x W x D approximate) 27” x 19” x 6.25” (685.8mm x 482.6mm x 158.75mm) 19” (482.6mm) 2” 4” 4” 7” 1.25” (50.8mm) (101.6mm) (101.6mm) (177.8mm) (31.75mm) 6.25” (158.75mm) 6.25” 10.76” (158.75mm) (273.3mm) 1.25” 0.85” 0.85” (31.75mm) (21.6mm) (21.6mm) 2.5”...
  • Page 16 Notes: Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 web site: www.altronix.com, e-mail: info@altronix.com, Lifetime Warranty, Made in U.S.A. MEMBER IIMaximal3D/5D/7D Series B04O - 16 - Maximal3D/Maximal5D/Maximal7D Access Power Controllers (PTC)

This manual is also suitable for:

Maximal3dMaximal5dMaximal7d

Table of Contents