1. Manuals
  2. Brands
  3. Altronix Manuals
  4. IP Access Controllers
  5. Maximal series
  6. Installation manual

Altronix Maximal Series Installation Manual

Access power controllers with power supplies
Hide thumbs Also See for Maximal Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Access Power Controllers with
Power Supplies
Installation Guide
Models Include:
Maximal3FDV
- 12VDC @ 4.6A or 24VDC @ 5.2A.
- Sixteen (16) PTC protected outputs.
Maximal5FDV
- 12VDC @ 8.6A.
- Sixteen (16) PTC protected outputs.
Maximal7FDV
- 24VDC @ 9.2A.
- Sixteen (16) PTC protected outputs.
Rev. SFDV031115
Installing Company: ________________ Service Rep. Name: ______________________________________
Address: ___________________________________________________ Phone #: _____________________
More than just power.
TM

Advertisement

Table of Contents
loading

Related Manuals for Altronix Maximal Series

Summary of Contents for Altronix Maximal Series

  • Page 1 Access Power Controllers with Power Supplies Installation Guide Models Include: Maximal3FDV - 12VDC @ 4.6A or 24VDC @ 5.2A. - Sixteen (16) PTC protected outputs. Maximal5FDV - 12VDC @ 8.6A. - Sixteen (16) PTC protected outputs. Maximal7FDV - 24VDC @ 9.2A. - Sixteen (16) PTC protected outputs.

  • Page 2: Table Of Contents

    Table of Contents: MaximalFDV Series Overview pg. 3 ............... . MaximalFDV Series Configuration Chart.

  • Page 3: Maximalfdv Series Overview

    MaximalFDV Series Overview: Altronix MaximalFDV Access Power/Controllers distribute and switch power to access control systems and accessories. They convert a 220VAC (working range 198VAC - 256VAC), 50/60Hz input into sixteen (16) independently controlled 12VDC or 24VDC PTC protected outputs. The outputs are activated by an open col- lector sink or normally open (NO) dry trigger input from an Access Control System, Keypad, Push Button, REX PIR, etc.

  • Page 4: Eflow Power Supply/Charger

    eFlow Power Supply/Charger: • Input: 220VAC (working range 198VAC - 256VAC), 50/60Hz. • For output voltage and supply current refer to MaximalFDV series Configuration Chart, pg. 3. • Auxiliary output rated @ 1A (unswitched). • Overvoltage Protection. • Built-in charger for sealed lead acid or gel type batteries. •...
  • Page 5 eFlow Auxiliary outputs (unswitched): For auxiliary device connection this output will not be affected by Low Power Disconnect or Fire Alarm Interface. Connect device to terminals marked [+ AUX –] (Fig. 3, pg. 9). 7. Input trigger options (Fig. 2, pg. 8): (a) Normally Open [NO] input trigger: Inputs 1-8 are activated by normally open or open collector sink inputs.

  • Page 6: Maintenance

    Maintenance: Unit should be tested at least once a year for the proper operation as follows: FACP Supervision: To ensure proper connection and operation of the Fire Alarm disconnect hookup. Please follow the appropriate procedure below: Normally Open Input: Placing a short between terminals marked [T] and [+ INP] will trigger the Fire Alarm Disconnect.

  • Page 7: Access Power Controller Terminal Identification

    Access Power Controller Terminal Identification: Terminal Legend Function/Description 12VDC or 24VDC from power supply/charger (factory connected). – Power + These terminals are paralleled to the [– Control +] terminals. These terminals are paralleled to the [– Power +] terminals. These terminals can be connected to an external access control power supply to provide –...

  • Page 8: Access Power Controller Typical Application Diagram (For Each Acm8)

    Access Power Controller Typical Application Diagram (for each ACM8CB): Fig. 2 Fig. 2a Intact = Dry Input Normally Open (N.O.) Cut = Wet Input Door Releasing FACP FACP Device Keypad Access Control Panel (Fire Alarm Fig. 2b Control Panel) Output FACP Dry Relay Form "C"...

  • Page 9: Maximalfdv Battery Hookup And Tamper Switch Installation

    Fig. 3 Maximal3FDV, Maximal5FDV, and Maximal7FDV. Tamper Switch Wire Ground Lug Strap (from Enclosure to Door) Power Supply Board AC FAIL BAT FAIL AC DELAY SHUTDOWN 5A 250V 1 min. enable TRIGGER EOL NC C NO NC C NO + AUX – 2 hr.

  • Page 10: Nec Power-Limited Wiring Requirements

    NEC Power-Limited Wiring Requirements: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through differ- ent conduits.

  • Page 11: Facp/Optional Power Supply Hook-Up Diagrams

    FACP Hook-Up Diagrams: Fig. 5 Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm condition): JUMPER J3 FACP OUTPUT EOL FROM FACP OUTPUT CIRCUIT Fig. 6 Normally Open: Non-Latching FACP Fig. 7 Normally Open FACP Latching trigger trigger input: input with reset: N.O.

  • Page 12: Enclosure Dimensions

    19” (482.6mm) Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty | Made in U.S.A. MEMBER IIMaximal3FDV/5FDV/7FDV Series G30R...

This manual is also suitable for:

Maximal3fdvMaximal5fdvMaximal7fdv

Table of Contents