Section 1: Introduction; Scope; 1: Reference Documentation - Honeywell Fire-Lite Alarms MS-9200 Wiring Manual

Intelligent control panel, slc

Table of Contents

1.1 Scope

This document describes the operation, installation and wiring of various Signaling Line Circuit (SLC) devices when used with the Fire-

Lite MS-9200, MS-9200E, MS-9600, MS-9600E, MS-9600LS, MS-9600LSC, MS-9600LSE, MS-9600UDLS, MS-9600UDLSE,

MS-9200UD, MS-9200UDE, MS-9200UDLS, MS-9200UDLSE, MS-9200UDLSC, MS-9050UD, MS-9050UDC, MS-9050UDE, ES-

50X, ES-50XC, ES-200X, and ES-200XC control panels. It also provides basic information that applies to Fire•Lite SLC loops in gen-

eral, such as the branch resistance measurements.

NOTE: Any reference in this manual to the MS-9200, MS-9200UD, MS-9200UDLS, MS-9600, MS-9600LS, MS-9600UDLS, MS-9050UD,

ES-50X, or ES-200X includes the MS-9200E, MS-9200UDE, MS-9200UDLSE, MS-9200UDLSC, MS-9600E, MS-9600LSE, MS-9600LSC,

MS-9600UDLSE, MS-9050UDC, MS-9050UDE, ES-50XC, or ES-200XC respectively unless otherwise specified.

Additional information about the specific control panel and the modules and detectors referenced in this document can be found in the

respective installation manual as listed in Section 1.1.1, "Reference Documentation".

Currently, there are two styles of modules available, legacy version and newer version. The obvious difference between the two styles is

the orientation of the rotary dials. Refer to the diagram below for an example of each.

NOTE: Only the MMF-300, MMF-302, CRF-300, CMF-300, and MDF-300 modules are available as newer type modules. Both the legacy

and newer versions share the same part numbers. The newer version modules will be phased in, replacing the legacy version. This manual

contains information and wiring diagrams for the newer version of the modules. Refer to "Terminal Conversion Charts for New & Legacy

Devices" on page 69 for additional information.

Currently, there are two styles of detector bases available, legacy version and newer version. The obvious difference between the two

styles is the orientation of the screw terminals. Refer to Section 9 and Appendix D for an illustration of each.

NOTE: Only the B501 Detector Base, B210LP Detector Base (replacement base for B350LP), B224RB Relay Base, and B224BI Isolator

Base are available as newer type bases. Both the legacy and newer versions share the same part numbers. The newer version bases will

be phased in, replacing the legacy version. This manual contains information and wiring diagrams for the newer version of the bases. Refer

to "Intelligent Detector Base Layouts for Legacy Devices" on page 72 for additional information.

1.1.1 Reference Documentation

The table below accommodates a list of document sources containing additional information regarding the devices used on a Signaling

Line Circuit:

For information on...

MS-9200, MS-9200E

MS-9600, MS-9600E

MS-9200UD, MS-9200UDE Control Panels

MS-9200UDLS, MS-9200UDLSE, MS-9200UDLSC Control Panels

MS-9600LS, MS-9600LS(C/E) & MS-9600UDLS, MS9600UDLSE Control Panels

MS-9050UD, MS-9050UDC, MS-9050UDE Control Panels

ES-50X, ES-50XC Control Panels

ES-200X, ES-200XC Control Panels

Compatible Devices

Wireless Sensor Network

BG-12LX Pull Station

MMF-300 Monitor Module

MMF-300-10 Monitor Module