Specifications - JUKI PS-800-12080 Instruction Manual

1. SPECIFICATIONS

1 Sewing area (X,Y)(mm)
2 Feed motion of feeding frame
3 Needle bar stroke
4 Max. sewing speed
5 Settable stitch length
6 Needle
7 Hook
8 Intermediate presser stroke
9 Lift of intermediate presser
10 Lift of disc presser
11 Memory of pattern data
12 Number of patterns that can be identified
13 Program input method
14 Data format
15 Main shaft servomotor power
16 Power consumption
17 Input voltage
18 Mass (gross mass)
19 Dimensions
20 Operating temperature range
21 Operating humidity range
22 Storage temperature range
23 Storage humidity range
24 Air pressure used
25 Needle highest position stop facility
26 Noise
27 Lubricating oil
S type
Stitch pitch and the sewing speed
Number Stitch pitch
1 2.8 mm
2 3.0 mm
3 4.0 mm
4 5.0 mm
Note: The sewing machine must not run at the maximum num-
ber of revolutions continuously for more than 15 minutes. The
number of revolutions may vary even if the pitch is consistent
due to the change in the needle and material.
1200 × 800
(Cutting area
Intermittent feed (2-shaft drive by stepping motor)
39.5 mm
[S type] 3,000 sti/min (When stitching pitch is 2.2 mm or less)
[H type] 1,800 sti/min (When stitching pitch is 3.5 mm or less)
For other stitch pitches and numbers of revolutions, refer to Fig. 1.
0.5 to 12.7 mm
[S type] DB × 1 #8 (#7 to #14), DP × 5 #8 (#7 to #14)
[H type] DP17 #21
To be chosen according to the model.
Double-capacity full-rotary hook
4 mm (Standard)
20 mm
15 mm
Max. 999 patterns
Max. 999 patterns
USB
DXF.AI.PLT.DST
[S type] 550W
470VA
220V ± 10%
780 kg [Rotary knife type] 788kg
2,180 mm (W) × 2,185 mm (L) × 1,250 mm (H)
5 to 35 ˚C [Laser type] 1 to 35 ˚C
35 to 85 % (No dew condensation)
-5 to 60 ˚C [Laser type] -10 to 100 ˚C
20 to 85 % (No dew condensation, 85 % applies to the case where the tem-
perature is 40 ˚C or lower)
[Laser type] 20 to 85 % (No dew condensation)
0.5 to 0.6 MPa
After the completion of sewing, the needle can be brought up to its highest
position.
- Equivalent continuous emission sound pressure level (L
tion :
A-weighted value of 78.0 dB ; (Includes K
10821- C.6.2 -ISO 11204 GR2 at 2,800 sti/min.
#10 (Equivalent to JUKI NEW DEFRIX OIL No. 1)
#32 (Equivalent to JUKI NEW DEFRIX OIL No. 2), Lithium based grease No. 2
Grease information
Manufacturer: WERATCHE
Type and number: Lithium base 2# grease
Sewing speed Remarks
2,800 sti/min
2,500 sti/min
2,200 sti/min
1,800 sti/min
Fig. 1
– 1 –
Rotary knife type : 698 × 391
Laser type : 646.5 × 426.5)
[H type] 750W
[Laser type] 850kg
[Laser type] 5 to 70 %
pA
H type
Stitch pitch and the sewing speed
Number Stitch pitch
1 3.5 mm
2 4.0 mm
3 4.5 mm
4 5.0 mm
Note: The number of revolutions may vary even if the
pitch is consistent due to the change in the needle
and material.
) at the worksta-
pA
= 2.5 dB) ; according to ISO
Sewing speed Remarks
1,800 sti/min
1,600 sti/min
1,400 sti/min
1,200 sti/min