Danfoss FC 102 Operating Manual page 83

Specifications
Control card, 24 V DC output
Terminal number
Maximum load
The 24 V DC supply is galvanically isolated from the supply voltage (PELV), but has the same potential as the analog and digital
inputs and outputs.
Relay outputs
Programmable relay outputs
Maximum cross-section to relay terminals
Minimum cross-section to relay terminals
Length of stripped wire
Relay 01 terminal number
Maximum terminal load (AC-1)
Maximum terminal load (AC-15)
Maximum terminal load (DC-1)
Maximum terminal load (DC-13)
Maximum terminal load (AC-1)
Maximum terminal load (AC-15)
Maximum terminal load (DC-1)
Maximum terminal load (DC-13)
Minimum terminal load on 1–3 (NC), 1–2 (NO)
Environment according to EN 60664-1
Relay 02 terminal number
Maximum terminal load (AC-1)
Maximum terminal load (AC-15)
Maximum terminal load (DC-1)
Maximum terminal load (DC-13)
Maximum terminal load (AC-1)
Maximum terminal load (AC-15)
Maximum terminal load (DC-1)
Maximum terminal load (DC-13)
Minimum terminal load on 4–6 (NC), 4–5 (NO)
Environment according to EN 60664-1
1) IEC 60947 part 4 and 5.
The relay contacts are galvanically isolated from the rest of the circuit by reinforced isolation (PELV).
2) Overvoltage Category II.
3) UL applications 300 V AC 2 A.
Control card, +10 V DC output
Terminal number
Output voltage
Maximum load
The 10 V DC supply is galvanically isolated from the supply voltage (PELV) and other high-voltage terminals.
Control characteristics
Resolution of output frequency at 0–1000 Hz
System response time (terminals 18, 19, 27, 29, 32, 33)
Speed control range (open loop)
Speed accuracy (open loop)
All control characteristics are based on a 4-pole asynchronous motor.
MG16O102
Operating Guide
1)
on 1–2 (NO) (Resistive load)
on 1–2 (NO) (Inductive load @ cosφ 0.4)
1)
1)
on 1–2 (NO) (Resistive load)
1) on 1–2 (NO) (Inductive load)
1) on 1–3 (NC) (Resistive load)
on 1–3 (NC) (Inductive load @ cosφ 0.4)
1)
1)
on 1–3 (NC) (Resistive load)
1)
on 1–3 (NC) (Inductive load)
1)
on 4–5 (NO) (Resistive load)
on 4–5 (NO) (Inductive load @ cosφ 0.4)
1)
1) on 4–5 (NO) (Resistive load)
1)
on 4–5 (NO) (Inductive load)
1)
on 4–6 (NC) (Resistive load)
on 4–6 (NC) (Inductive load @ cosφ 0.4)
1)
1)
on 4–6 (NC) (Resistive load)
1) on 4–6 (NC) (Inductive load)
Danfoss A/S © 01/2017 All rights reserved.
2)3)
Overvoltage category III/pollution degree 2
2)3)
Overvoltage category III/pollution degree 2
30–4000 RPM: Maximum error of ±8 RPM
12, 13
200 mA
2
2.5 mm (12 AWG)
0.2 mm 2 (30 AWG)
8 mm (0.3 in)
1–3 (break), 1–2 (make)
400 V AC, 2 A
240 V AC, 0.2 A
80 V DC, 2 A
24 V DC, 0.1 A
240 V AC, 2 A
240 V AC, 0.2 A
50 V DC, 2 A
24 V DC, 0.1 A
24 V DC 10 mA, 24 V AC 2 mA
4–6 (break), 4–5 (make)
400 V AC, 2 A
240 V AC, 0.2 A
80 V DC, 2 A
24 V DC, 0.1 A
240 V AC, 2 A
240 V AC, 0.2 A
50 V DC, 2 A
24 V DC, 0.1 A
24 V DC 10 mA, 24 V AC 2 mA
50
10.5 V ±0.5 V
25 mA
±0.003 Hz
≤2 ms
1:100 of synchronous speed
81
2
9 9