CrimeStopper Super Rage CS-2011RS Installation Instructions Manual
  1. Manuals
  2. Brands
  3. CrimeStopper Manuals
  4. Car Alarm
  5. CS-2011RS Series III Super Rage
  6. Installation instructions manual
CrimeStopper Super Rage CS-2011RS Installation Instructions Manual

CrimeStopper Super Rage CS-2011RS Installation Instructions Manual

Remote control alarm system & remote engine starting system
Hide thumbs Also See for Super Rage CS-2011RS:

Advertisement

Table of Contents

Remote Control Alarm System & Remote Engine Starting System
To ease and reduce installation time, we suggest you consider the following points before starting:
BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR
BAGS, ABS BRAKES, AND BATTERY).
USE A VOLT/OHM METER to test and locate all connections. Test Lights can damage a vehicle's computer
systems.
ADDITIONAL PARTS, which are not included with this unit, may be needed for your particular vehicle. These
items may include extra relays, Anti-Theft System Bypass modules, or Transponder Bypass modules.
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific
Website: www.crimestopper.com
E-mail: tech-support@crimestopper.com
CRIMESTOPPER
SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063
CS-2011RS
Super Rage™
INSTALLATION INSTRUCTIONS
INSTALLATION CAUTIONS & WARNINGS
This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: 1) This device may not cause
interference, and (2) this device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference
caused
by
equipment. Such modification could void the user's authority to
operate the equipment.
unauthorized
modification
to
this

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Super Rage CS-2011RS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for CrimeStopper Super Rage CS-2011RS

Summary of Contents for CrimeStopper Super Rage CS-2011RS

  • Page 1 ADDITIONAL PARTS, which are not included with this unit, may be needed for your particular vehicle. These items may include extra relays, Anti-Theft System Bypass modules, or Transponder Bypass modules. TECHNICAL SUPPORT (800)-998-6880 Monday - Friday 8:00am - 4:30pm Pacific Website: www.crimestopper.com E-mail: tech-support@crimestopper.com CRIMESTOPPER SECURITY PRODUCTS, INC.

  • Page 2: Installation Cautions & Warnings

    INSTALLATION CAUTIONS & WARNINGS DO NOT remote start the vehicle in a closed garage. Make sure that the garage door is open or there is adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes.

  • Page 3: Wiring 6-Pin High Current Connector/14 Gauge Wires

    WIRING: 6-PIN High Current Connector (14 Gauge wires) PIN 1: BROWN: STARTER OUTPUT (30A) PIN 2: GRAY: ACCESSORY or IGNITION 2 (30A) PIN 3: RED: BATTERY CONSTANT FUSED (30A) PIN 4: RED: BATTERY CONSTANT FUSED (30A) PIN 5: PINK: IGNITION 1 (30A) PIN 6: WHITE (18 Ga.): (+) PARKING LIGHTS (10A) PARKING LIGHTS...
  • Page 4 WIRING: 9-PIN Harness (22 Gauge wires) Green: (-) Start Activation Trigger This wire allows an additional source or accessory to activate a Remote Start. A 1-second Ground pulse on this wire will trigger a remote start. This wire must be used with the RS400 CoolTimer Temperature / Timed Start Accessory (Not included).
  • Page 5 WIRING: 9-PIN Harness (22 Gauge wires) Blue/Black: (-) Remote Aux. Output 2 (Optional, may require relay) This wire provides a Momentary<-> Negative output when Button #3 (Trunk) is pressed and held for more than 2 seconds. Output stays on as long a remote button is held down. Blue/White: (-) Passenger Door Unlock Output (Optional) This wire activates when the unlock button on the remote is pressed a second time when upon disarming.
  • Page 6 WIRING: 4-PIN Harness (18/22 gauge wires) Red/White: Tachometer Input When installing the CS2011RS in TACH REFERENCE mode, this wire must be connected to a valid source of AC voltage. This wire allows the unit to sense the engine and control the starter motor. Black: Chassis Ground Connect to body metal of the vehicle using a sheet metal screw and a star washer.
  • Page 7 WIRING: 5-PIN Harness (22 gauge wires) Pink: (+12V) Diesel Glow Plug Input or Car Jack Input (Programmable Input Wire) Glow Plug (Diesel): Connect to the indicator circuit that shows +12 volts while the “WAIT TO START LAMP” is on. When this wire is used, the CS2011RS will wait until light turns off before attempting a remote start.
  • Page 8 WIRING: 4-PIN Shock Sensor (22 Gauge wires) 4 Pin Plug - Sensor Plug 22 Gauge -: White Wire - Negative Trigger Blue Wire - Negative Warn Away Black Wire - Sensor Ground Red Wire - Sensor +12Volt Power Sensor Adjustment Adjust the main shock sensor with the small black dial.
  • Page 9 REVERSE POLARITY DOOR LOCK WIRING GREEN BLUE MASTER SWITCH SEPARATE DRIVER’S DOOR UNLOCK WIRING BLUE/WHITE GREEN BLUE DRIVER'S DOOR MOTOR UNLOCK WIRE DOOR LOCK WIRING AFTERMARKET MOTOR/DOOR LOCK WIRING GREEN FUSED +12V BLUE NEGATIVE TRIGGER DOOR LOCKS FACTORY LOCK RELAYS +12V FUSED FUSED...

  • Page 10: Smart Tachless Mode

    SEPARATE DRIVER’S DOOR UNLOCK WIRING WIRING FOR REVERSE POLARITY DOOR LOCKS BLUE/WHITE GREEN BLUE MASTER SWITCH UNLOCK WIRE The CS2011RS includes a Tachless engine monitor. When in Smart Tachless mode, the module actively monitors the vehicle over the life of the installation regardless of weather or battery conditions. Tachless mode will adjust to compensate for most conditions for optimum operation efficiency.
  • Page 11 Some locations will NOT be a good location for Tach source due to RF noise or Computer Data. If you cannot locate a good tach signal, then call Crimestopper for Tech Support. TACH REFERENCE PROGRAMMING: 1.

  • Page 12: Transmitter Programming

    Note: All transmitter codes must be learned at time of programming!! The CS2011RS allows storage of up to 4 different transmitter codes. 1. Open Hood. (Blue wire grounded.) 2. Turn key to the ON position. (Doors will lock if Autolock is programmed) 3.
  • Page 13 Option Description Autolock with Ignition Door Lock Pulse Time Double Unlock Pulse Tach Learning Remote Start Engine Run Time Option reset Passive Arming Active Re-Arm Passive Locks Parking Lights on w/Disarm GREEN/RED Wire PINK Wire 1. AUTOLOCK/UNLOCK W/IGNITION Controls whether the doors will automatically lock when the ignition is turned on and will unlock when the ignition is turned off.
  • Page 14 PROGRAMMABLE OPTIONS 3. DOUBLE UNLOCK PULSE With this option ON, the unit will send 2 unlock pulses when the system is disarmed. This feature may be required for interfacing this alarm with some existing Factory Unlock systems. Factory Default setting is OFF. 4.

  • Page 15: Remote Start Troubleshooting

    REMOTE START TROUBLESHOOTING UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START: The unit is in Valet mode. Turn IGN ON, press and hold valet/programming button for about 5 seconds unit LED goes out. Unit is now out of valet mode and should perform a remote start. UNIT FLASHES LIGHTS TWICE AND WILL NOT ATTEMPT A START: The unit sees a fault at the Brake (White wire is active) or the Hood is OPEN (Blue wire grounded).

  • Page 16: General Wiring Diagram

    YELLOW (-) ACC YELLOW/WHITE BLACK BROWN (+) SIREN (-) START ACTIVATION INPUT WHITE (+) BRAKE SWITCH INPUT ANTENNA / RECEIVER CS-2011RS ALARM/ DUAL-STAGE SHOCK SENSOR REMOTE START STATUS (-) NEG. LOCK GREEN +12V FOR RELAYS BLUE (-) NEG. UNLOCK VIOLET...

Table of Contents

Save PDF