CrimeStopper CS-2015.FM.RevB Installation Instructions Manual
Combo alarm & remote engine starter
Hide thumbs
Also See for CS-2015.FM.RevB:
- Installation handbook (30 pages) ,
- Installation instructions manual (27 pages)
Table of Contents
Advertisement
CS-2011RS Series II / CS-2015FM
Super Rage™
To ease the installation, we suggest that you READ THIS MANUAL and consider the following points
before beginning your installation.
BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS,
ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY).
PLAN OUT YOUR INSTALLATION. You should pre-determine the location of the Control Module (Brain), Valet
button, LED, and Siren locations. This will save time and ease the installation process.
USE A VOLT/OHM METER to test and locate all connections. Test Lights or Lighted Probes could possibly damage a
vehicle's computer system or cause an airbag to deploy.
ADDITIONAL PARTS, that are not included with this unit, may be needed for your particular vehicle. These items may
include extra relays (Part#CS-402A), General Motors Anti-Theft System Bypass modules for Vats / Passkey® /
Passlock® Systems, (Part# CS-GMATA II) or Transponder Anti-Theft Adapter modules (Part # CS-TATA).
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific
Website: www.crimestopper.com
E-mail: tech-support@crimestopper.com
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063
REV C 10.2001 S/W: 580
INSTALLATION INSTRUCTIONS
PRE-INSTALLATION CONSIDERATIONS
The Informer™
This device complies with FCC Rules part 15. Operation is
subject to the following two conditions: 1) This device may not
cause interference, and (2) this device must accept any
interference that may be received, including interference that
may cause undesired operation.
responsible for any radio or TV interference caused by
unauthorized
modification
modification could void the user's authority to operate the
equipment.
The manufacturer is not
to
this
equipment.
Such
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CrimeStopper CS-2015.FM.RevB
Summary of Contents for CrimeStopper CS-2015.FM.RevB
- Page 1 Passlock® Systems, (Part# CS-GMATA II) or Transponder Anti-Theft Adapter modules (Part # CS-TATA). TECHNICAL SUPPORT (800)-998-6880 Monday - Friday 8:00am - 4:30pm Pacific Website: www.crimestopper.com E-mail: tech-support@crimestopper.com CRIMESTOPPER SECURITY PRODUCTS, INC. 1770 S. TAPO STREET SIMI VALLEY, CA. 93063 REV C 10.2001 S/W: 580 The Informer™...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Pre-Installation Considerations………………………...……...………………………………………………………Front Cover Cautions & Warnings…….……………………………..…..………………………………………………………………………2 Component Mounting………….………………………..……………………………………………….…………………..……..3 Wiring……..…………………………………………………...…………………………………………………………….…….3-9 Power Door Lock Wiring...………………………………………………………….………….……..…………...……………9-12 Smart Tachless, Tach Reference, & Tach Finder Modes…………………………………………………………………13-14 Transmitter / Transceiver Programming…………………………….………………….…………………………...…...….14-15 Programmable Options……...………………………………………….……………………………….………….…………15-18 Diagnostics……………………………………..……………………………………………………………………….………….18 Remote Start Troubleshooting…….……………………..………………………………………………………………...…….19 System Wiring Diagram…………………………………………………………………………………………………...………20 CAUTIONS & WARNINGS DAMAGE RESULTING FROM IMPROPER INSTALLATION IS NOT COVERED UNDER WARRANTY!! DO NOT remote start the vehicle in a closed garage. -
Page 3: Component Mounting
CONTROL MODULE: The alarm control module should be mounted in a concealed location. DO NOT mount the control unit in the engine compartment. Fasten the module to a bracket or wire harness using the cable ties provided. ANTENNA MODULE: For optimum range and performance, the antenna/receiver module should be located high up on the front windshield glass. - Page 4 Green/Red: Remote Aux. Output 1 OR MAP-Mobile Accessories Protection (Optional, requires relay) This is a programmable output that can operate two different ways: 1. (DEFAULT) A Remote Auxiliary Output that provides a ½ Second (-) Negative pulse when Button #3 is pressed to open a Factory power trunk or hatch release. It can function as an MAP output that provides a continuous (-) Negative output when in the system is put into VALET PARK MODE.
- Page 5 Orange: (-) Negative Starter Disable / Anti-Grind Output IGN. SWITCHED CONNECT TO ORANGE WIRE OF ALARM PRE-WIRED STARTER DISABLE RELAY & SOCKET START OUTPUT FROM ALARM 6-PIN HARNESS Orange/Black: (-) OEM Disarm Output This wire provides a Ground pulse to disarm vehicles' Factory anti-theft system prior to a Remote Start. Connect this wire to the vehicles' anti-theft disarm wire.
- Page 6 WIRING: 6-PIN High Current Connector PARKING LIGHTS WHITE +10A MAX. FUEL ENGINE PUMP COIL HEAT/AC NOTE!: Use External Relays for High Current Ignition and/or Accessory circuits greater than 30A. Failure to do so could result in damage to the unit that is not covered under warranty. This diagram is provided as a guide.
- Page 7 Red/White: Tachometer Input When installing this system in TACH REFERENCE mode, this wire must be connected to a valid source of AC voltage. This wire allows the unit to sense the engine running. See Tach Reference Section on Pg. 13 for more information. Black: Chassis Ground Connect to body metal of the vehicle using a sheet metal screw and a star washer to ensure a good ground.
- Page 8 Blue: (-) Hood/Trunk Pin Switch Input Input trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk pin switches that read ground when open. If no existing switches are available, install new pin switches if desired. Note: DO NOT mount new pin switches in water pathways.
-
Page 9: Power Door Lock Wiring
Incorrect connection could result in damage to the alarm and/or the vehicle’s locking system. We have provided a brief description and test procedure for common door locking systems under “DOOR LOCK SYSTEMS page 10. Crimestopper Doorlock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. -
Page 10: Door Locking Systems
Actuator (motor) in the Driver’s door. The Actuator will electronically control the drivers for lock and unlock which will cause all doors to now lock and unlock with the alarm. Actuators are available from Crimestopper (Part # CS- 610S1) at a low cost. Installing actuators can be difficult and time-consuming. (Varies from vehicle to vehicle.) Electric Vacuum Pump: Mid 1980’s through Mid 1990’s European Makes (Mercedes, Audi) - Page 11 NEGATIVE TRIGGER DOORLOCK WIRING GREEN BLUE REVERSE POLARITY DOOR LOCK WIRING GREEN BLUE MASTER SWITCH DOOR LOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN BLUE FACTORY POWER LOCKING RELAYS ADDING AFTERMARKET DOOR LOCK MOTORS GREEN FUSED +12V BLUE FUSED +12V FACTORY POWER LOCKING RELAYS...
-
Page 12: Wiring
SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGATIVE TRIGGER DOOR LOCKS BLUE/WHITE GREEN BLUE DRIVER'S DOOR MOTOR +12V FUSED UNLOCK WIRE WIRING FOR REVERSE POLARITY DOOR LOCKS BLUE/WHITE GREEN BLUE MASTER SWITCH 30 87A UNLOCK WIRE FACTORY LOCK RELAYS FUSED +12V LOCK WIRE... -
Page 13: Smart Tachless, Tach Reference, & Tach Finder Modes
SMART TACHLESS MODE Both the CS2011RS & CS2015FM include a Tach-less engine monitor called “Smart Tachless” mode. When in “Smart Tachless” mode, the module actively monitors the vehicle’s voltage reference each time a remote start is performed. Smart Tachless mode will adjust itself to maintain optimum efficiency over the life of the life of the installation. No special wiring is required for Smart Tachless mode. -
Page 14: Transmitter / Transceiver Programming
TACH FINDER & TACH PROGRAMMING STEPS TACH FINDER: 1. Open hood (or Ground the Blue Hood Pin wire if no hood pin is installed) 2. Start Engine with the key. 3. Press the Program button for 2 seconds 4. Lights will begin flashing if the White/Red wire is connected to a valid tach 5. -
Page 15: Programmable Options
PROGRAMMING – CS-2015FM TRANSCEIVER / CS-2011RS TRANSMITTER (BLUE WIRE GROUNDED) CS-2015FM To access programmable options: 1. Open hood (Ground Blue wire if no hood pin is installed). 2. Turn Key to the ON position 3. Press program button 5 times, after a few seconds the unit will flash the lights 5 times. 4. -
Page 16: Programmable Options Table
PROGRAMMABLE OPTIONS TABLE Option # Option Description Tach Learning Autolock with Ignition ON or OFF. Passive Arming Active Re-Arm Passive Locks Parking Lights on w/Disarm GREEN/RED Wire function PINK Wire function Siren Chirps on Remote Start Disarm on Trunk pop ON or OFF Open Door Warning Door Lock Pulse Time... - Page 17 PROGRAMMABLE OPTIONS 1. TACH LEARNING This option has no values or default settings. See Tach (RPM) Reference Mode Section on pages 13-14. 2. AUTOLOCK/UNLOCK W/IGNITION Controls whether the doors will automatically lock when the ignition is turned on and will unlock when the ignition is turned off.
-
Page 18: Programmable Options
11. 10/60 Sec. OPEN DOOR WARNING This setting changes the delay time in which the alarm system begins to monitor the Door circuit. This option can prevent the alarm from giving warning chirps on vehicles with a delayed dome light. 12. -
Page 19: Remote Start Troubleshooting
REMOTE START TROUBLESHOOTING UNIT FLASHES THE LIGHTS ONCE AND WILL NOT ATTEMPT A REMOTE START: (3 parts) 1. The system may be in Valet mode. Check the systems LED light and if it is on solid Red LED (with doors closed) then the system is in VALET mode. -
Page 20: System Wiring Diagram
30AMP FUSE RED: +12V 30AMP BATTERY RED: +12V FUSE FLASHING LIGHTS IGNITION 1 ACC/IGN 2 (Heat/Air) IGNITION SWITCH STARTER TACH INPUT WHITE/RED ORANGE/BLACK (-) NEG. PULSE (-) OEM DISARM FOR FACTORY ALARM DISARM ORANGE (-) ARMED OUTPUT (500mA) CONNECT TO YELLOW WIRE OF RELAY SOCKET BLUE/WHITE...
Need help?
Do you have a question about the CS-2015.FM.RevB and is the answer not in the manual?
Questions and answers