Table of Contents
Advertisement
Available languages
Available languages
5.
With one person supporting the drawer front, use an 8 mm socket
wrench to remove the ten screws (5 on each bracket) fastening the
drawer front to the left-hand and right-hand glide rails.
a
6.
Set the drawer front onto a soft surface to protect the finish. Slide the
rails back into the cabinet.
7.
Perform the previous steps in reverse order to replace the freezer
drawer front.
CONNECT TO WATER
A cold water supply with water pressure of between 30 and
(207 and 689 kPa)
maker. If you have questions about your water pressure, call a licensed,
qualified plumber.
IMPORTANT:
•
Connect only to a drinking (potable) water supply.
•
Plumbing shall be installed in accordance with the International
Plumbing Code and any local codes and ordinances.
Connect to Water Line
Gather the required tools and parts before starting installation.
•
Flat-blade screwdriver
•
1/2
" Wrench or 2 Adjustable
wrenches
•
Cordless drill
1/2
1.
Find a
refrigerator.
IMPORTANT: Make sure it is a cold water pipe.
NOTE: Horizontal pipe will work; however, you must drill on the top
side of the pipe, not the bottom. Drilling on the top side will keep
water away from the drill and keep normal sediment from collecting in
the valve.
2.
Determine the length of copper tubing you need. Measure from the
connection on the back of the refrigerator to the water pipe. Add 7 ft
(2.1 m) to allow for cleaning. Use
copper tubing. Be sure both ends of copper tubing are cut square.
16
is required to operate the water dispenser and ice
1/4
" to 1
" (12.7 mm to 31.8 mm) vertical cold water pipe near the
a
Screws
•
1/4
" Drill bit
•
1/4
" Compression nut
•
Ferrule (sleeve)
1/4
" (6.35 mm) O.D. (outside diameter)
100 psi
Hide quick links:
Advertisement
Chapters
Table of Contents
Need help?
Do you have a question about the MRQ22D7AST and is the answer not in the manual?
Questions and answers
My control panel on the drawer has gone out. Due to this, neither ice maker is working and we can't adjust temps on anything. Is there a way to reset this? We have tried unplugging the fridge for 30 seconds. What else can I try? If I have to replace the control panel on the drawer, how do I do that?
How do you correct a E6 code
The E6 error code on the Midea MRQ22D7AST refrigerator indicates a communication failure between the main board and the display board. To fix this issue, try the following steps:
1. Power Cycle the Refrigerator – Unplug the refrigerator from the power source for a few minutes, then plug it back in and check if the error clears.
2. Check Connections – Ensure that the wiring connections between the main board and the display board are secure and undamaged.
3. Reset the Control Panel – If the refrigerator has a reset function, use it to restart the system.
4. Contact Customer Support – If the error persists, contact Midea customer service or a qualified technician for further diagnosis and repair.
If the refrigerator is under warranty, consider requesting service from an authorized Midea technician.
This answer is automatically generated
We are seeing a EO on the display panel. We hold hold the control lock for seconds and it goes away. However it returns. Not sure what the EO means and how to get rid of it.
The E0 error code on the Midea MRQ22D7AST display panel indicates a freezer ice maker initialization failure. To resolve this issue, try the following steps:
1. Power Cycle the Appliance – Unplug the refrigerator for a few minutes and then plug it back in to reset the system.
2. Check the Ice Maker – Ensure the ice maker is properly connected and not obstructed.
3. Inspect for Ice Blockages – Remove any ice buildup that may be preventing the ice maker from initializing.
4. Verify Water Supply – Ensure the water line is connected and supplying water to the ice maker.
5. Contact Support – If the issue persists, contact Midea customer service or an authorized technician for further assistance.
If the error continues, professional service may be required.
This answer is automatically generated