Table of Contents
Advertisement
Available languages
Available languages
6.
À l'aide d'une clé à douille de 8 mm, enlever les trois vis de charnière.
7.
À l'aide d'un tournevis Phillips, enlever la vis de mise à la terre
(charnière de porte gauche seulement).
a
b
c
REMARQUE : Prévoir un support additionnel des portes pendant le
démontage des charnières. Ne pas compter sur les aimants du joint de
porte pour maintenir la porte en place pendant le travail.
8.
Retirer la charnière de porte supérieure.
9.
À deux mains, ouvrir délicatement la porte qu'à obtenir un angle
de 90° avec la caisse, puis soulever la porte pour la dégager de la
charnière inférieure. Poser la porte sur une surface douce afin d'en
protéger le revêtement.
10.
Répéter ces étapes pour retirer la porte du réfrigérateur droite.
RÉINSTALLATION DES PORTES
REMARQUE : L'axe de la charnière descend plus bas que le bord inférieur
de la porte.
1.
Insérer l'axe de la charnière dans l'ouverture de la charnière inférieure.
2.
Insérer la charnière supérieure sur le haut de la porte.
3.
Au moyen des vis de charnière enlevées précédemment, serrer la
charnière supérieure sur la partie supérieure de la caisse.
4.
Réinstaller la vis de mise à la terre (porte gauche seulement).
5.
Rebrancher les quatre faisceaux de câbles (porte gauche seulement).
6.
Rebrancher le tuyau d'alimentation en eau (porte gauche seulement).
a
Vis de
charnière
b
Vis de terre
c
Charnière
supérieure
90°
13
Hide quick links:
Advertisement
Chapters
Table of Contents
Need help?
Do you have a question about the MRQ22D7AST and is the answer not in the manual?
Questions and answers
My control panel on the drawer has gone out. Due to this, neither ice maker is working and we can't adjust temps on anything. Is there a way to reset this? We have tried unplugging the fridge for 30 seconds. What else can I try? If I have to replace the control panel on the drawer, how do I do that?
How do you correct a E6 code
The E6 error code on the Midea MRQ22D7AST refrigerator indicates a communication failure between the main board and the display board. To fix this issue, try the following steps:
1. Power Cycle the Refrigerator – Unplug the refrigerator from the power source for a few minutes, then plug it back in and check if the error clears.
2. Check Connections – Ensure that the wiring connections between the main board and the display board are secure and undamaged.
3. Reset the Control Panel – If the refrigerator has a reset function, use it to restart the system.
4. Contact Customer Support – If the error persists, contact Midea customer service or a qualified technician for further diagnosis and repair.
If the refrigerator is under warranty, consider requesting service from an authorized Midea technician.
This answer is automatically generated
We are seeing a EO on the display panel. We hold hold the control lock for seconds and it goes away. However it returns. Not sure what the EO means and how to get rid of it.
The E0 error code on the Midea MRQ22D7AST display panel indicates a freezer ice maker initialization failure. To resolve this issue, try the following steps:
1. Power Cycle the Appliance – Unplug the refrigerator for a few minutes and then plug it back in to reset the system.
2. Check the Ice Maker – Ensure the ice maker is properly connected and not obstructed.
3. Inspect for Ice Blockages – Remove any ice buildup that may be preventing the ice maker from initializing.
4. Verify Water Supply – Ensure the water line is connected and supplying water to the ice maker.
5. Contact Support – If the issue persists, contact Midea customer service or an authorized technician for further assistance.
If the error continues, professional service may be required.
This answer is automatically generated