Advertisement
CAUTION: Read and follow all instructions before operating the fan. Do not use the fan if any part is damaged or missing.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state speed control device
1.
Never insert fingers or any other objects through the cage guard when the fan is in operation.
2.
Close supervision is necessary when any appliance is used by or near children.
3.
Disconnect the fan when moving from one location to another.
4.
Disconnect the fan when removing grill guard for cleaning, servicing, maintenance, and before moving to another location.
5.
Be sure the fan is on a stable, flat surface when in operation.
6.
DO NOT use the table fan in windows. Rain and moisture may create an electrical hazard.
7.
DO NOT operate fan in the presence of explosive and/or flammable fumes.
8.
DO NOT place fan or any parts near an open flame, cooking or other heating appliances.
9.
DO NOT operate any appliance with a damaged cord or plug, after the appliance malfunctions, or has been dropped or damaged in any manner.
10. To disconnect, grip the plug and pull from wall outlet. Never pull on the cord.
11. To protect against electrical shock, do not immerse the fan, plug, or cord in water or spray with liquids.
12. DO NOT put fan in a damp place or where humidity is high, such as a bathroom.
13. DO NOT use near curtains, plants, window treatments, et cetera.
14. This appliance has a grounded three-prong plug and is suitable for grounded receptacle use only. An adaptor is available from your local hardware store for connecting
three-prong grounding-type plugs to two-slot receptacles. The adapter must be properly grounded. DO NOT attempt to defeat the purpose of this safety feature.
15. Improper installation may result in a risk of fire, electrical shock, or personal injury.
16. ALWAYS use on a dry surface.
17. Use fan only for intended use.
18. This product is intended for household use only and not for commercial or industrial use.
Table & Desk Fan: No assembly required. Please skip to the Important Saftey
Instructions below.
Floor Fan:
1. Make sure you are familiar with the 3 components: Motor Cage Assembly,
Pipe Assembly, and Base Assembly.
2. a)Lay the Motor Cage Assembly on a flat, protected surface, face down.
b)Ensure that the neck is showing the cord indent and that it is perfectly
in line with the knob at the back of the motor housing.
3. Take the Pipe Assembly and make sure that the collars on both ends are
pulled in enough to expose the notch in the pipe.
4. Take the cord from the Motor Cage Assembly and feed it through the pipe
(both ends are the same). Make sure the plug clears the end of the pipe.
5. Align the pipe collar onto the neck post of the Motor Cage Assembly,
sliding the tab of the motor cage into the notch of the pipe.
6. Thread the collar and turn the until it is snug.
7. a)Lay the base of the fan on it's side close to the pipe. The male pin
connector is on the neck of the base, note that one side has a locking
tooth.
b) make sure that where the cord comes out is perfectly in line with the
knob at the back of the motor housing.
8. Assure that the latch and locking tooth are matched up and plug the wire
from the pipe into the fan base. Move the collar away from the end and
slide the pipe onto the fan base, but do not tighten the collar yet.
9. a) With one hand hold the handle of the motor cage and with the other
hold the neck of the base and tilt the fan up to a standing position.
b) Before tightening down the collars be sure that the knob at the back of
the motor housing is still in line with where the cord is coming out of the
base.
10. a) Align the tab from the base to the notch in the pipe. Thread and
tighten the collar for the base of the fan, tighten completely.
b) You may need to adjust the alignment of the knob at the back of the
motor housing with the cord coming out of the base as you tighten the
collars. The proper alignment of the notches in step 5 and step 10 will
help keep this alignment as you tighten the collars.
11. Set the floor fan up where the cord will not be in a traffic area or tripped
on. Also make sure the oscillation movement of the cage is not impeded
in any way.
READ & SAVE THESE INSTRUCTIONSSAFETY FIRST
IMPORTANT SAFETY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Step 5
TAB
NOTCH
Step 5
Step 8
Step 9
NOTCH
TAB
Step 10
Advertisement
