Page 2
MANUAL SB60 Gas & Diesel Models Serial Numbers 1000 to current When contacting UpRight for service or parts information, be sure to include the MODEL and SERIAL NUMBERS from the equipment nameplate. Should the nameplate be missing the SERIAL NUMBER is also stamped on top of the chassis in the rear.
Page 3
Please understand that these warnings cannot cover all conceivable ways in which service, whether or not recommended by UpRight, Inc., might be Illustrated Parts done, or of the possible hazardous consequences of each conceivable way, nor could UpRight Inc.
Page 5
Introduction & Specifications Section 1.0 Introduction PURPOSE OF EQUIPMENT The objective of the SB60 Work Platform is to provide a PURPOSE quickly deployable, self propelled, variable height work platform to elevate personnel and materials to overhead The purpose of this service and parts manual is to work areas.
Page 6
12VDC Controls Electric Proportional Maximum Hyd. Pressure 5000 psi Tires 14 ply lug tread (80 psi) Table 1-1: Specifications * Specifications subject to change without notice. Meets or exceeds all applicable requirements of OSHA and ANSI A92.5-1992 SB60 Work Platform...
Page 7
NEVER alter operating or safety systems without manufacturers written consent. NEVER charge batteries near sparks or open flame. Charging batteries emit explosive hydrogen gas. NEVER replace any component or part with anything other than original UpRight replacement parts without the manufacturer's written consent.
Page 8
Introduction This manual covers the operation of internal com- bustion powered models of the SB60 Boom. If you smell propane, close the supply valve on the tank immediately until you have located and corrected the leak. Pre-Operation and Safety Inspection...
Page 9
25. Boom/Turret control 26. Boom extension control 27. Cage rotate control 28. Jib control 29. Cage level control 30. Drive control handle/interlock 31. Lights (optional) 32. Engine start switch 33. Foot interlock switch Figure 2-3: Platform Controls SB60 Work Platform...
Page 10
They will indicate the direction of travel when the drive control handle is moved. Figure 2-6: Typical Fall Restraint Anchorage Point SB60 Work Platform...
Page 11
Release the control lever to stop elevating / lowering. The boom elevate will function The UpRight SB60 employs the use of multifunction at a speed proportional to the stroke of the joy- controls. This means that any two functions can stick.
Page 12
3. Turn the key switch to OFF and remove the key to move the machine or when winching onto a trailer to prevent unauthorized operation. for transportation. SB60 Work Platform...
Page 13
7. Attach ratchet strap under platform floor grating, transportation. over support braces. (Figure 2-9) Do not over tighten. NEVER elevate the machine while on a truck Chassis Tie Down or trailer. Lifting Lugs Figure 2-10: Rear chassis tie down lifting lugs. SB60 Work Platform...
Page 14
Tire selection can affect the stability of the machine. Engine running or stopped. (see figure 2-12) Use only tires supplied by UpRight (15-19.5 NHS 2. If necessary, fill to capacity with clean ISO Tubeless 14 Ply Rating ) unless approved by the compatible hydraulic oil.
Page 15
Section 2.0 will aid in understanding the operation and GENERAL PROCEDURES function of the various components and systems of the SB60 and help in diagnosing and repair of the machine. CONTACT BLOCKS: Removed by inserting a flat Refer to Table 3-1, Preventative Maintenance Checklist, screwdriver into the slot at either end of block and for recommended maintenance intervals.
Page 16
(Table 3-1) The following is a list of special tools which may be required to perform certain maintenance procedures on the SB60 work platform. The complete inspection consists of periodic visual and operational checks, together with all necessary minor SuperFlex Optimizer (P/N 100329-000) adjustments to assure proper performance.
Page 17
ISO grade 46, for temperatures above 32F (0 C). Check Lubricate ring gear (MoS grease) For colder climates: ISO grade 32, for temperature range of 0 F (-17C) up to 32F (0 C). * ISO grade 15, for temperatures below 0 F (-17C). SB60 Work Platform...
Page 18
4. Turn platform/chassis switch to CHASSIS. 5. Using the Elevate Boom Switch, elevate platform 8-12 inches. 6. Using an overhead hoist (preferred) or jackstand with minimum capacity of Two tons; Support the boom. Figure 3-3: Supporting Elevating Assembly SB60 Work Platform...
Page 19
Hazard of explosive gas mixture. Keep sparks, flame, and smoking material away from battery. Always wear safety glasses when working with batteries. Battery fluid is highly corrosive. Thoroughly rinse away any spilled fluid with clean water. SB60 Work Platform...
Page 20
NOTE: For service Information on the engine refer Oil and Filter Replacement to your engine manual (located in platform manual box or available from UpRight Inc.). 1. Operate the platform for 10-15 minutes to bring the hydraulic oil up to normal operating temperature.
Page 21
(both LED's on) when joystick is centered. NOTE: Check that controller operates correctly when handle is pushed completely forward and reverse. Figure 3-8: Boom Extend Controller Refer to pages 6-50 (Gas) and 6-54 (Diesel) for repair part numbers. SB60 Work Platform...
Page 22
Use the Optimizer to test the operation of the control- optimizer (P/N 100329-000) to check for proper con- ler and joysticks. SB60 presets are shown. troller settings. 1. Plug the Optimizer with cord into the controller.
Page 23
1/4" to 3/8". Lower the platform and retest. If down limit switch is properly adjusted, the tilt alarm will not sound. 4. With platform elevated, repeat step 2. When switch is properly adjusted, alarm will sound. SB60 Work Platform...
Page 24
5. Operate each hydraulic function and check for 4. Remove the bolts that hold the manifold to the proper operation and leaks. mounting bracket. 6. Adjust lift relief and counterbalance valve pressures 5. Remove manifold block. according to instructions in Section 3-9. 3-10 SB60 Work Platform...
Page 26
IMPORTANT: If replacing the pump, be sure the pump and hydraulic tank are filled with oil before starting the engine. Damage to the pump may occur if it is run without first being filled with oil. 3-12 SB60 Work Platform...
Page 27
10. Remove jack stands and lower rear end. 6. Remove the wheel nuts and wheel. 11. Connect battery terminal. 7. Disconnect hydraulic brake line from brake. 12. Operate machine and check for proper operation of torque hub. Check function of brake. SB60 Work Platform 3-13...
Page 28
1. Slide the coupling (1) from splines on input shaft (2). (11) should be centered as it is lowered over spindle 2. Position the assembly upright on face of spindle (3). (3) to prevent seal damage. 3. Remove the disengage cover (31) if necessary.
Page 29
(22)} with planet gear teeth in secondary carrier assembly (21). Assemble primary sun gear (24) over input shaft (2). Rotate primary sun gear (24) to align input shaft (2) to gear splines and gear teeth in primary carrier assembly (22). SB60 Work Platform 3-15...
Page 30
25. Thrust Washer 18. Washer 32. Hex Head Bolt 27. O-Ring 19. Disengage Spring 33. Quick Disconnect Gasket 20. Ring Gear 34. Quick Disconnect Assy. 21. Secondary Carrier Assy. 35. Hex Head Bolt Figure 3-15: Torque Hub 3-16 SB60 Work Platform...
Page 31
1. If any counterbalance relief valve is faulty, com- pletely lower the jib, and retract the boom. 2. Replace or recalibrate the counterbalance valve. 3. Slowly cycle function related to replaced counter- balance valve several times to remove air from system. SB60 Work Platform 3-17...
Page 32
2. Steering 14. Dump 3. Cage Level 15. Boom Power 4. Swing (Turret) 16. Pressure Test Port 5. Lift Boom 6. Boom Extend 7. High Pressure Extend Relief 8. Low Pressure Extend Relief 9. Main Relief 3-18 SB60 Work Platform...
Page 33
Seal kit (100553-010) includes: 1. O-Ring 5. O-Ring A. Rod 2. Wiper 6. Backup B. Head 3. Seal 7. O-Ring C. Piston 4. Wear Ring 8. Seal D. Locknut 9. Wear Ring E . Cylinder Figure 3-18: Master Cylinder SB60 Work Platform 3-19...
Page 34
Seal kit (100552-010) includes: 5. O-Ring 1. O-Ring A. Rod 6. Back-Up 2. Wiper B. Head 7. O-Ring 3. Seal C. Piston 8. Seal 4. Wear Ring D. Locknut 9. Wear Ring E . Cylinder Figure 3-19: Slave Cylinder 3-20 SB60 Work Platform...
Page 35
Figure 3-20: Axle Lock Cylinder cylinder. 2. Install new seal kit items to piston and head. 3. Lubricate rod wiper and seal with hydraulic oil and slide head onto rod. SB60 Work Platform 3-21...
Page 36
5. Back up D. Cylinder elastically restore to their original shape before 6. O-Ring assembling cylinder. 7. Wear Ring 8. Seal Figure 3-21: Steering Cylinder 3-22 SB60 Work Platform...
Page 37
1. Wiper 6. Back Up A. Rod 7. O-Ring 2. Seal B. Head 8. Seal 3. Wear Ring C. Piston 9. Wear Ring 4. O-Ring D. Locknut 5. O-Ring E . Cylinder Figure 3-22: Jib Cylinder SB60 Work Platform 3-23...
Page 38
2. Install new seal kit items to piston and head. 3. Lubricate rod wiper and seal with hydraulic oil and slide head onto rod. 4. Slide piston onto rod. 3-24 SB60 Work Platform...
Page 39
1. O-Ring B. Head 7. Back up C. Spacer 2. Wiper 8. O-Ring D. Piston 3. Seal 9. Wear Ring E . Locknut 4. Seal 10. Seal 5. O-Ring F. Cylinder Figure 3-24: Boom Extend Cylinder SB60 Work Platform 3-25...
Page 40
.005" per mating set. After long service, a backlash of about .015" per set may still be acceptable in most cases, depending on the required Figure 3-25 accuracy of the application. 3-26 SB60 Work Platform...
Page 41
The housing and shaft to rotate simulta- with integral ring neously. The double helix gear remains design compounds rotation: stationary. shaft rotation is about twice that of the piston. Figure 3-26 SB60 Work Platform 3-27...
Page 42
5. Inspect the body and housing for scratches, pits, or polishing. Check seal grooves and sealing surfaces. Scratches or pits deep enough to catch the finger- nail are unacceptable, replace the manifold. 3-28 SB60 Work Platform...
Page 43
FASTENERS preservation procedures. PRESERVATION Use the following values to torque fasteners used on UpRight Work Platforms unless a specific torque value is 1. Clean painted surfaces. If paint is damaged, called out for the part being installed. repaint. Table 3-3: Bolt Torque 2.
Page 44
Section Maintenance 3.20 NOTES: 3-30 SB60 Work Platform...
Page 45
Referring to Section 2.0 and 5.0 will aid in understand- Disconnect the battery ground cable when ing the operation and function of the various compo- nents and systems of the SB60 and help in diagnosing replacing or testing the continuity of any and repair of the machine.
Page 46
Troubleshooting Section THEORY OF OPERATION SPECIAL TOOLS The operating functions of the SB60 are powered by Following is a list of tools which may be required to two hydraulic pumps. perform certain maintenance procedures on the SB60. The large Rexroth pump powers the drive wheels and Flow Meter with Pressure Gauge (UpRight P/N the smaller Barnes pump powers all the other functions.
Page 47
M aster Cylinder O vercenter Valves O scillating Axle Cylinder Platform Rotator Platform Rotator Flow Divider .2 G PM Platform Rotator Relief Valves Platform Rotator Valve Pum p Retract Orifice 4.5 G PM Retract Relief Return Filter SB60 Work Platform...
Page 48
W ater Temperature Gauge W ater Temperature Sending Unit Oil Pressure Guage Oil Pressure Sending Unit Hour Meter Oil Pressure Switch Aux Power Relay Coil Aux Power Relay Contacts Propane Relay Coil Propane Relay Contacts Gasoline Relay Coil SB60 Work Platform...
Page 49
Jib Up R elay C oil Jib Up R elay C ontacts Jib Down Solenoid Jib Down R elay C oil Jib Down R elay C ontacts Jib Switch Platform Rotate R ight Solenoid Platform Rotate R ight R elay C oil SB60 Work Platform...
Page 50
X X X X X X X X X Lower Control Interlock Switch X X X X X X X X X Lower Control Start Switch High Pressure Extend Relay Coil High Pressure Extend Relay Contacts High Pressure Extend Solenoid SB60 Work Platform...
Page 51
Section 5-7 Lower Controller Assembly - Gas ing tables. Section 5-8 Upper Controller Assembly - Diesel Section 5-9 Upper Controller Assembly - Gas Section 5-10 Engine Module Assembly - Diesel Section 5-11 Engine Module Assembly - Gas SB60...
Unit pressure meter Relay Shift Lower Control Assy SNSR3 Temp Sending Unit Provides input to Eng Module Assy Relay Steer R Lower Control Assy temperature meter Relay Steer L Lower Control Assy STR1 Starter Turns engine Eng Module Assy SB60...
Relay Brake/High Throt Lower Control Assy SW11 Switch Aux Power Lower Control Assy Relay Boom Power Lower Control Assy SW12 Switch Swing – Slew Lower Control Assy Relay Ignition Lower Control Assy SW13 Switch Oil Pressure Eng Module Assy SB60...
TAN (QTY 1) 12 GA BLK POWER CHASSIS GROUND MODULE 12 GA RED STARTER SOLENOID GRN/BLK BLU/BLK BLK/WHT RED/BLK BLU/WHT RED/WHT CONTROL MODULE ORG/BLK GRN/WHT WHT/BLK 12 GA RED/BLK AUX. POWER LOWER CONTROLLER ASSEMBLY, DIESEL 100018-000 DRAWING 1 OF 2 5-18 SB60...
WIRE HARNESS 100336-016 WIRE HARNESS 068773-003 JUMPER, 3 PIN 060214-099 CABLE 16 GA 15 COND 100338-001 CONNECTOR, FEMALE 21 PIN 100338-011 CONN, 12 GA PIN 100338-013 CONN, 16 GA PIN 100338-005 BOOT 068764-000 PLUG SEALING SEE NEXT PAGE SB60 5-19...
Page 70
CONN FORK (#6 DIA) 16-14 GA 29610-003 CONN FORK (#6 DIA) 12-10 GA 29601-012 CONN RING (#8 DIA) 16-14 GA 29931-003 CONN FEM PUSH (.25) 16-14 GA 29931-005 CONN FEM PUSH (.25) 12-10 GA 29610-001 CONN FORK 22-18 GA #6 5-20 SB60...
BLUE (QTY 1) TAN (QTY 1) POWER MODULE 12 GA RED STARTER SOLENOID GRN/BLK BLU/BLK BLK/WHT RED/BLK BLU/WHT RED/WHT CONTROL MODULE ORG/BLK GRN/WHT WHT/BLK 12 GA RED/BLK AUX. POWER LOWER CONTROLLER ASSEMBLY, GAS 100019-000 DRAWING 1 OF 2 5-22 SB60...
Page 73
WIRE HARNESS 100316-016 WIRE HARNESS 068773-003 JUMPER, 3 PIN 060214-099 CABLE 16 GA 15 COND 100338-001 CONNECTOR, FEMALE 21 PIN 100338-011 CONNECTOR, 12 GA PIN 100338-013 CONNECTOR, 16 GA PIN 100338-005 BOOT 68764-000 PLUG SEALING SEE NEXT PAGE SB60 5-23...
Page 74
CONN FORK (#6 DIA) 12-10 GA 29601-012 CONN RING (#8 DIA) 16-14 GA 29931-003 CONN FEM PUSH (.25) 16-14 GA 29931-005 CONN FEM PUSH (.25) 12-10 GA 29610-001 CONN FORK 22-18 GA #6 29601-019 CONN T&B RC 367 12 GA RING 5-24 SB60...
Page 80
Section Schematics Upper Control Assembly SB60 Diesel 100016-001 ITEM PART DESCRIPTION QTY. 301 029452-099 WIRE, 16 GA BLACK 302 029451-099 WIRE, 16 GA WHITE 303 029454-099 WIRE, 16 GA RED 304 029457-099 WIRE, 16 GA GREEN 305 029450-099 WIRE, 16 GA BLUE...
Page 82
Section Schematics ITEMS 1-3 ARE PART OF CONTROLLER KIT 100336-000 CALLED OUT IN THE LOWER CONTROL BOX ASSY. UPPER CONTROLLER ASSEMBLY, GAS, SB60 100017-000 DRAWING 1 OF 3 5-32 SB60...
Page 84
ORIENT CLEATS TO INSIDE BLUE ORANGE 225 224 DETAIL A LINE DRILL AT ASSEMBLY USE PERMABOND #910 OR EQUAL TO SECURE MCMASTER-CARR P/N 7580A52 MOUNTING HARDWARE PROVIDED WITH ALARM UPPER CONTROLLER ASSEMBLY, GAS SB60 100017-000 DRAWING 2 OF 3 5-34 SB60...
Page 85
Section Schematics Upper Controller Assembly Gas, SB60 100017-000 ITEM PART DESCRIPTION QTY. 201 100309-000 UPPER CONTROL BOX 202 029925-002 CONNECTOR CABLE 1/2 NPT 203 029939-002 LOCKNUT 1/2 NPT 204 100334-000 SWITCH, LEVER 205 067893-000 MOUNTING RAIL DIN X 13 LG...
Page 86
Section Schematics Upper Controller Assembly Gas, SB60 100017-000 ITEM PART DESCRIPTION QTY. 301 029452-099 WIRE, 16 GA BLACK 302 029451-099 WIRE, 16 GA WHITE 303 029454-099 WIRE, 16 GA RED 304 029457-099 WIRE, 16 GA GREEN 305 029450-099 WIRE, 16 GA BLUE...
Page 93
Illustrated Parts Breakdown 6.0 Introduction This section lists and illustrates the replaceable assem- blies and parts of the SB60 Work Platform, as manufac- tured by UpRight, Inc. Each parts list contains the component parts for that assembly indented to show relationship where appli- cable.
Page 103
HOSES THRU. LOCATE IN TURRET 42"LG 42 BLUE LOCTITE #242 - 190 LBS TORQUE ADD OR SUBTRACT ITEM #50 AS REQUIRED TO MAKE TOTAL WEIGHT OF ITEM #5 AND 50 - 3170 ±63LBS. SEE NOTE 2 SB60 Work Platform 6-11...
JAM NUT 5/8-11 R E F 100277-000 SLEW LOCK WELDMENT 100386-099 HOSE GUARD 100278-000 PIN, SLEW LOCK 100595-007 LOCKING PIN 011256-020 SCREW HHC 1/2-13 UNC X 2-1/2 011707-024 SCREW, SET HEX SOC 1/2-13 UNC X 3 6-14 SB60 Work Platform...
Page 107
Section Illustrated Parts Breakdown SB60 Work Platform 6-15...
Page 115
Section Illustrated Parts Breakdown ENGINE MODULE ASSEMBLY, SB60 ENGINE REPAIR PARTS DIESEL SB60, DIESEL 100012-000 ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY. 201 100338-000 CONNECTOR, MALE (21 PIN) 100180-005 OIL FILTER 202 100338-005 BOOT 100180-006 FUEL FILTER 205 100338-012...
Page 116
TO FUEL TANK ROUTE FUEL LINE THRU LOOM ITEM #77 FERRUEL AND SEE DETAIL A NUT SUPPLIED W/ ENGINE PUMP (ITEM 3) 2 13/32 COUPLING (ITEM 59) DETAIL A ENGINE MODULE ASSEMBLY, DIESEL 100012-000 DRAWING 1 OF 2 6-24 SB60 Work Platform...
Page 117
Section Illustrated Parts Breakdown SB60 Work Platform 6-25...
Page 118
ACCUMULATOR (125 PSI) 011248-005 LOCKNUT, 5/16-18 UNC ESNA 011253-006 SCREW, HHC 5/16-18 X 3/4 011252-006 SCREW, HHC 1/4-20 X 3/4 011238-004 LOCKWASHER, 1/4" SPLIT RING NOTE: Items 51-63 supplied with item 1, engine PN 100200-000 * Not shown 6-26 SB60 Work Platform...
Page 119
100200-036 COUPLER KIT-SPLINE 236 029825-002 DIODE 237 014435-001 BATTERY TERMINAL 238 029616-003 CONN. FEMALE PUSH 12-10 239 029419-099 WIRE, 12 GA RED/GRN 240 029418-099 WIRE, 12 GA RED/BLK 241 029601-025 CONN. RING TERM 0-5/16 8 GA SB60 Work Platform 6-27...
Page 120
SEE DETAIL A HARDWARE ROUTE WIRES THRU 16 16 LOOM AS NEEDED. ROUTE FUEL LINE THRU LOOM ITEM #77 PUMP (ITEM 3) 2 11/16 COUPLING (ITEM 59) DETAIL A ENGINE MODULE ASSEMBLY, GAS 100013-000 DRAWING 1 OF 2 6-28 SB60 Work Platform...
Page 121
Section Illustrated Parts Breakdown SB60 Work Platform 6-29...
Page 122
J-BOLT 011254-006 SCREW HHC GRS 3/8-16 UNC X 3/4 011250-004 NUT HEX 1/4-20 UNC 064195-010 BATTERY CABLE ASSY X 10 R E F 064195-019 BATTERY CABLE ASSY X 19 R E F 010154-000 COVER, BATTERY TERMINAL 6-30 SB60 Work Platform...
Page 123
Section Illustrated Parts Breakdown SB60 Work Platform 6-31...
Page 124
3/4" HOSE ASSY X 58" 12FFORX-12FFORX 100429-012 1/2" HOSE ASSY X 12" 8FFORX-8FFORX 020032-001 FITTING, TEE 4MJ-4MJ-4MJ 100436-001 FITTING, TEE 4MFFOR-4MFFOR-4MFFOR 100429-015 1/2" HOSE ASSY X 15" 8FFORX-8FFORX 020032-004 FITTING, TEE 8MJ-8MJ-8MJ 100427-018 3/4" HOSE ASSY X 18" 12FFORX-12FFORX 6-32 SB60 Work Platform...
Page 125
Section Illustrated Parts Breakdown SB60 Work Platform 6-33...
Page 126
1/2 HOSE X 27 LG 8FJX-8FJX 90° 222 100431-051 3/4 HOSE X 51 LG 12FFORX-FLANGE 90° 224 100438-094 1 HOSE X 94 LG 16FJX-16MP 225 100439-088 1-1/4" HOSE X 88 LG 20FJX-20MP 226 100431-058 3/4 HOSE X 58 LG 12FFORX-FLANGE 90° 6-34 SB60 Work Platform...
Page 127
Section Illustrated Parts Breakdown SB60 Work Platform 6-35...
Page 128
1/4 HOSE X 60 LG 4FJX-4FJX 90° 311 060861-115 3/8 HOSE X 51 LG 6FJX-6FJX 313 060861-120 3/8 HOSE X 120 LG 6FJX-6FJX 314 060861-150 3/8 HOSE X 150 LG 6FJX-6FJX 315 060861-210 3/8 HOSE X 210 LG 6FJX-6FJX 6-36 SB60 Work Platform...
Page 129
Section Illustrated Parts Breakdown SB60 Work Platform 6-37...
DIODE, 5 AMP, 400V 217 015790-004 PIN CONTACT 16-18G 329 029601-013 CONN, RING 16-14 #10 330 029610-006 CONN, FORK 16-14 #6 331 029616-002 CONN, FEMALE PUSH 16-14 332 029490-099 WIRE 16 GAUGE, 2 COND, TYPE SO 6-42 SB60 Work Platform...
Page 135
Section Illustrated Parts Breakdown ITEMS 1-3 ARE PART OF CONTROLLER KIT 100336-000 CALLED OUT IN THE LOWER CONTROL BOX ASSY. UPPER CONTROLLER ASSEMBLY, GAS, SB60 100017-000 DRAWING 1 OF 3 SB60 Work Platform 6-43...
Page 136
TO INSIDE BLUE ORANGE 225 224 DETAIL A LINE DRILL AT ASSEMBLY USE PERMABOND #910 OR EQUAL TO SECURE MCMASTER-CARR P/N 7580A52 MOUNTING HARDWARE PROVIDED WITH ALARM UPPER CONTROLLER ASSEMBLY, GAS, SB60 100017-000 DRAWING 2 OF 3 6-44 SB60 Work Platform...
Page 137
Section Illustrated Parts Breakdown SB60 Work Platform 6-45...
Page 138
241 029610-001 CONN FORK 22-18 GA #6 068773-003 JUMPER, 3 PIN 060214-099 CABLE 16 GA 15 COND 100338-001 CONNECTOR, FEMALE 21 PIN 100338-011 CONN, 12 GA PIN 100338-013 CONN, 16 GA PIN 100338-005 BOOT 068764-000 PLUG SEALING 6-46 SB60 Work Platform...
Page 139
12 GA BLK POWER CHASSIS GROUND MODULE 12 GA RED STARTER SOLENOID GRN/BLK BLU/BLK BLK/WHT RED/BLK BLU/WHT RED/WHT CONTROL MODULE ORG/BLK GRN/WHT WHT/BLK LOWER CONTROLLER 12 GA RED/BLK ASSEMBLY, DIESEL AUX. POWER 100018-000 DRAWING 1 OF 2 SB60 Work Platform 6-47...
Page 140
Section Illustrated Parts Breakdown 6-48 SB60 Work Platform...
Page 141
Section Illustrated Parts Breakdown NOTES: SB60 Work Platform 6-49...
Page 142
CONN T&B RC 367 12 GA RING 100316-016 WIRE HARNESS 068773-003 JUMPER, 3 PIN 060214-099 CABLE 16 GA 15 COND 100338-001 CONNECTOR, FEMALE 21 PIN 100338-011 CONNECTOR, 12 GA PIN 100338-013 CONNECTOR, 16 GA PIN 100338-005 BOOT 068764-000 PLUG SEALING 6-50 SB60 Work Platform...
Page 143
BLUE (QTY 1) POWER TAN (QTY 1) MODULE 12 GA RED STARTER SOLENOID GRN/BLK BLU/BLK BLK/WHT RED/BLK BLU/WHT RED/WHT CONTROL MODULE ORG/BLK GRN/WHT WHT/BLK LOWER CONTROLLER ASSEMBLY, GAS 100019-000 12 GA RED/BLK AUX. POWER DRAWING 1 OF 2 SB60 Work Platform 6-51...
Page 144
Section Illustrated Parts Breakdown 6-52 SB60 Work Platform...
Page 145
Section Illustrated Parts Breakdown NOTES: SB60 Work Platform 6-53...
Page 146
NUT 5/16-18 ESNA 011252-006 SCREW HHC 1/4-20 UNC X 3/4 LG 011248-004 NUT 1/4 ESNA 014996-004 WASHER 1/4 SAE FLAT 011252-008 SCREW HHC 1/4-20 UNC X 1 LG 011238-005 WASHER 5/16 LOCK 011240-004 WASHER 1/4 FLAT 6-54 SB60 Work Platform...
Page 147
Section Illustrated Parts Breakdown CUT TO 73-1/2" LG BALL WITH RETAINING CLIP DETAIL BALL & CLIP MOUNTING CUT TO 69-1/4" LG CUT TO 58-1/2" LG KEEPER SUPPLIED WITH LATCH (ITEM 5) SB60 Work Platform 6-55...
Page 161
Section Illustrated Parts Breakdown SB60 Work Platform 6-69...
Page 162
Illustrated Parts Breakdown TIRE & WHEEL ASSEMBLY 100090-000 - LEFT HAND 100090-001 - RIGHT HAND ITEM PART DESCRIPTION QTY. 100091-000 WHEEL, 19.5 X 12 9 HOLE 100092-000 TIRE, 19.5 X 15 NHS 14 PLY 012282-001 VALVE STEM 6-70 SB60 Work Platform...
Page 164
LIFT-GATE WELDMENT 100481-000 ROLLER TUBE 011253-022 SCREW, HHC 5/16-18 UNC X 2-3/4 011248-005 LOCKNUT, HEX 5/16-18 UNC ESNA 100468-000 PANEL, DECAL MOUNT 026551-005 POP RIVET, 1/8" DIA. (3/1601/4 GRIP) NOTE: LINE DRILL FOR RIVETS AT ASSY. 6-72 SB60 Work Platform...
Page 165
Section Illustrated Parts Breakdown NOTES: SB60 Work Platform 6-73...
Page 166
SCREW 1/4-20 UNC HHC X 3/4 LG (LP-538) FITTING, STRAIGHT, 8MP-3/4 BARB 011238-004 WASHER 1/4 SPLIT LOCK 029931-003 CONN. F PUSH 011240-004 WASHER 1/4 FLAT 014914-003 CONN. M PUSH * Items 2-27 included in item 1 dual fuel kit 100228-000 6-74 SB60 Work Platform...
Page 167
Section Illustrated Parts Breakdown SB60 Work Platform 6-75...
Page 168
Section Illustrated Parts Breakdown 6-76 SB60 Work Platform...
Page 169
Section Illustrated Parts Breakdown NOTES: SB60 Work Platform 6-77...
Page 170
100096-000 ITEM PART DESCRIPTION QTY. 066807-004 ALARM-112 DB 029616-002 CONN F PUSH 16-14 GA 029452-099 WIRE 16 GA BLK 011252-004 SCREW HHC 1/4-20 UNC X 1/2 011240-004 WASHER, FLAT 1/4 029617-002 CONN M PUSH 16-14 GA 6-78 SB60 Work Platform...
Page 171
FLASHING STROBE LIGHT 013283-002 CABLE TY WRAP 029496-099 WIRE 2 COND 16 GA 011709-008 SCREW #10-24 X UNC X 1 LG 011248-003 LOCKNUT #10-24 UNC ESNA 029610-002 CONN FORK 16-14 GA 029620-002 CONN BUTT 16-14 GA SB60 Work Platform 6-79...
Page 172
011937-004 FITTING SWIVEL 90° 8FJX-8MJ 029456-099 WIRE YEL 16 GA 014693-004 FITTING REDUCER 8MJ-6MJ 029454-099 WIRE RED 16 GA 020733-003 FITTING TEE 8FJX-8MJ-8MJ 029453-099 WIRE ORN 16 GA 020733-002 FITTING TEE 6FJX-6MJ-6MJ 011941-002 FITTING STR 4MB-6MJ 6-80 SB60 Work Platform...
Page 173
Section Illustrated Parts Breakdown SB60 Work Platform 6-81...
Page 175
Section Illustrated Parts Breakdown SB60 Work Platform 6-83...
Page 176
Section Illustrated Parts Breakdown CORD ASSEMBLY - GENERATOR OPTION SB60 100705-000 ITEM PART DESCRIPTION QTY. 100320-099 WIRE 3 COND. 12 GA 026614-000 PLUG, STRAIGHT FEMALE 026613-000 PLUG, STRAIGHT MALE 6 FT 6-84 SB60 Work Platform...
Page 177
PART DESCRIPTION QTY. 060861-001 ALARM - 112 DB 060861-049 CONN. F PUSH 16-14 GA 060861-063 WIRE 16 GA BLK 060861-074 SCREW HHC 1/4-20 UNC X 1/2 060861-076 WASHER, FLAT 1/4 060861-103 CONN. M PUSH 16-14 GA SB60 Work Platform 6-85...
Page 178
Section Illustrated Parts Breakdown NOTES: 6-86 SB60 Work Platform...
Page 179
Call Toll Free in U.S.A. 1-800-926-LIFT UpRight, Inc. 1775 Park Street Selma, California 93662 TEL: 209/891-5200 FAX: 209/896-9012 PARTS: 1-888-UR-PARTS PARTSFAX: 209/896-9244 100029-000 9901 .1 K Rev-A...