1. Manuals
  2. Brands
  3. Nabco Manuals
  4. Indoor Furnishing
  5. GYRO TECH GT-1175
  6. Installation manual

Nabco GT1175 Installation Manual

Standard and pocketed slide doors
Hide thumbs Also See for GT1175:
Table of Contents

Advertisement

Quick Links

Associated Manuals Part Numbers: OPUS Wiring and Programming Manual P/N C-00139
• Turn OFF all power to the Automatic Door if a Safety System is not working.
WARNING
• Instruct the Owner to keep all power turned OFF until corrective action can be achieved
• NEVER leave a Door operating without all Safety detection systems operational.

Table of Contents

CHAPTER 1: WARNING LABELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
CHAPTER 2: GENERAL SAFETY RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
CHAPTER 3: SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SECTION 3.1: To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SECTION 3.2: Objective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CHAPTER 4: GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SECTION 4.2: Associated Video QR Code Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SECTION 4.3: Types of Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SECTION 4.4: Feature Comparison between Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SECTION 4.5: Header Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CHAPTER 5: BEFORE ASSEMBLING DOOR FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CHAPTER 6: ASSEMBLE DOOR FRAME (NO TRANSOM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CHAPTER 7: ASSEMBLE DOOR FRAME WITH TRANSOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION 7.1: Secure Transom Verticals to Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION 7.2: Install the Glass Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SECTION 7.3: Secure Header and Transom to Pocketed Jamb Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SECTION 7.4: Assemble the Door Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SECTION 7.5: Install the Tie Rods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CHAPTER 8: SECURE DOOR FRAME TO BUILDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SECTION 8.1: Anchor Placements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SECTION 8.2: Complete the Tie Rod Installation (For Transom Units only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Model GT1175 Standard and Pocketed Slide Doors Installation Manual
NABCO Entrances Inc. S82 W18717 Gemini Drive Muskego, Wisconsin 53150
Phone: (877) 622-2694 Fax: (888) 679-3319 www.nabcoentrances.com
NABCO hours of Operation: Monday to Friday 8:00 a.m.- 4:30 p.m. (Central Time)
Automatic Sliding Door Owners Manual (P/N C-00109) for Decal Installation
NABCO Price Book P/N 16-9244-30 (for Sensors, Switches, and Accessories)
by a NABCO trained technician. Failure to follow these practices may result in serious
consequences.
**with Opus Controller**
P/N C-00370 Rev 11-12-20
1 of 62

Advertisement

Table of Contents
loading

Related Manuals for Nabco GT1175

Summary of Contents for Nabco GT1175

  • Page 1: Table Of Contents

    WARNING • Instruct the Owner to keep all power turned OFF until corrective action can be achieved by a NABCO trained technician. Failure to follow these practices may result in serious consequences. • NEVER leave a Door operating without all Safety detection systems operational.
  • Page 2 GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 CHAPTER 9: WIRE THE SWITCH ASSEMBLY (ROCKER SWITCH OR KEY SWITCH) . . . . . . . . . . 14 CHAPTER 10: INSTALL THE THRESHOLD .
  • Page 3 GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 CHAPTER 19: ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 SECTION 19.1: Adjust Horizontal Position of Carrier .

  • Page 4: Chapter 1: Warning Labels

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 CHAPTER 1: WARNING LABELS Warning labels are universal and used to alert an individual of potential harm to one’s self or to others. The following warning labels are listed in a hierarchy order that defines the most potential danger first, and the least potential danger last.

  • Page 5: Chapter 3: Scope

    All installation changes and adjustments must be made by qualified, NABCO trained technicians. The GT1175 Standard Slide Door system is designed to be installed within a Rough Opening of a Building. The door function SECTION 3 .2: Objective is controlled by the Opus Control.

  • Page 6: Section 4.4: Feature Comparison Between Controls

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 Emergency Egress:   • Full Open: Both the Slide door and Swing Sidelite breakout for emergency egress. • Fixed Sidelite: Secured to the Header and Jamb Tube. Only the Slide door breaks out for emergency egress.

  • Page 7: Chapter 6: Assemble Door Frame (No Transom)

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 R.O. WIDTH 1-3/4” 1/4” (6mm) RECESS 4-1/2” THRESHOLD 90.0° 90.0° R.O. HEIGHT RECESS THRESHOLD FLOOR 1/2” Figure 1 Masonry Opening FINISHED FLOOR 1/4” 1/4” (6mm) (6mm) DN 1740 SECTION 5 .2: Remove the Header Cover Cover in Swing 10-24 x .625”...

  • Page 8: Chapter 7: Assemble Door Frame With Transom

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 Fixed Sidelite: Removable Cover side of Header must face the Exterior side of building. 2. Orientate the Frame in relation to the building: Full Open: Removable Cover side of Header must face the Interior side of building.

  • Page 9: Section 7.2: Install The Glass Stops

    Attention:  Examples shown within the Glass Stop sections are of the GT1175 Standard Slide Door . Note: Each Glass Stop is precut at the NABCO Factory according to placement and height of the Transom Vertical. Note: Glass Panels can be installed before or after the Door Frame is secured to the rough opening.
  • Page 10 GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20  7 .2 .2 Transoms and Jamb Tubes 1. Go underneath the Transom Horizontal. Snap-In Base Glass Stops between the Transom Verticals. a. Ensure the tall back of Base Glass Stops face the Exterior side of building.

  • Page 11: Section 7.3: Secure Header And Transom To Pocketed Jamb Tubes

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 Vinyl Vinyl Base Glass Stop Vinyl Figure 12 Install Base Glass Stops and Vinyl on Same Side DN 2146 SECTION 7 .3: Secure Header and Transom to Pocketed Jamb Tubes Note: 1175 Slide Door Units installed with a Transom are shipped with Pocket Jamb Tubes only.

  • Page 12: Section 7.5: Install The Tie Rods

    Rev 11-12-20 SECTION 7 .5: Install the Tie Rods Note:  Tie Rods are provided for Transom Units as required by NABCO Engineering. 1. Lift to position the assembled Frame into the rough opening. 2. Shim and Plumb Jamb Tubes in both planes to ensure the rough opening allows a 1/4 inch clearance.

  • Page 13: Chapter 8: Secure Door Frame To Building

    Figure 20 Shim and Plumb Frame Header DN 0760 Anchors are not provided by NABCO. Anchors must be appropriate for the type of structure being fastened to. SECTION 8 .1: Anchor Placements   Screw in anchors to secure the Frame (per manufacturer’s specifications).

  • Page 14: Section 8.2: Complete The Tie Rod Installation (For Transom Units Only)

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 36” 48” 36” 48” 48” 48” Figure 21 Anchor Placement DN 0767 SLIDE DOOR w/TRANSOM SLIDE DOOR Note: It is recommended to countersink holes as required to flush the surface.

  • Page 15: Chapter 10: Install The Threshold

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 5. Obtain (1) Switch Assembly and (2) 10-32 x 1/2 inch Phillips Head Screws from the Parts Box. 6. Connect the Switch Harness from the back of the Switch Assembly to the Main Harness. Place extra wiring back inside the Jamb Tube.
  • Page 16 GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 2. Locate (2) screw splines on the exposed side(s) of the Threshold. 3. Secure (1) Threshold End Cap to the screw spline(s) with (2) 6 x 3/8 inch Phillips Head screws.

  • Page 17: Section 10.2: Install The Recessed Threshold

    7. With a 1/4 inch masonry drill bit, drill through the Threshold and into the floor no less than 1-1/2 inch deep. 8. Do not permanently install the Surface Threshold until the Slide Doors are completely installed. Metal Strip Fasteners not provide by NABCO Figure 32 Secure Threshold to Flat Surface DN 2114 RECESSED THRESHOLD CHAPTER 11: INSTALL THE INTERIOR FULL OPEN SIDELITE (POCKETED)

  • Page 18: Section 11.1: Install The Bottom Pivot

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 Attention:  The Full Open Interior Sidelite does not use the Limit Arm or Ball Detents . SECTION 11 .1: Install the Bottom Pivot 1/4-20 x 1/2”...

  • Page 19: Section 11.3: Install The Clip

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SECTION 11 .3: Install the Clip Attention:  To breakout the FO Interior Sidelite, (1) Clip must be removed from Strike Stile, and (1) Clip must be released from Header . 1. Go to the bottom of the Strike Stile. Align the screw hole located on the upper portion of Clip to the Strike Stile.

  • Page 20: Section 12.3: Install The Full Open Sidelite Onto The Upper Pivot And Bottom Pivot

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 3. Go to the pre-drilled screw hole located at the bottom of Header (on the Pivot Side of Sidelite). 4. Secure the Limit Arm to the Header by tightening the Screw.

  • Page 21: Section 12.5: Adjust The Ball Detents

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SECTION 12 .5: Adjust the Ball Detents Note: Breakout resistance for Ball Detents must meet ANSI Standard A156.10 or Local Codes. 1. Go to the top of the Strike Stile. With a 15/16” Open End wrench, loosen the Nut to raise or lower the Ball Detent so it has light contact with the Bottom of Header.

  • Page 22: Section 13.1: Secure The Fixed Sidelite To The Door Frame

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 SECTION 13 .1: Secure the Fixed Sidelite to the Door Frame 1. Locate (2) Cut Outs on the side of the Pivot Stile. Align and then slide the Fixed Sidelite until (2) Mounting Brackets (pre- installed on the Pivot Jamb Tube) can be seated inside each Cut Out.

  • Page 23: Section 13.3: Install The Floor Bracket

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 2. Install the Bottom Guide by sliding rollers into the Bottom Rail so the Bracket sticks out from underneath (in direction of where the Slide door is to be installed). 3. Use the Bracket to slide the Bottom Guide towards the Pivot Stile. Replace the Cover Plate.

  • Page 24: Section 14.1: Secure Slide Door To Belt Clips

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 SECTION 14 .1: Secure Slide Door to Belt Clips Do not test Breakout until all adjustments are made and doors are secured . CAUTION 1. Cover the Sidelite Panel with cardboard on the side that will face the Slide door.

  • Page 25: Section 14.3: Adjust Rollers

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 Li Up Bo om Guide; Prongs Guide Channels Figure 57 Drop Prongs into Channel Guides DN 0894  14 .2 .2 Secure Bottom Guide to the Fixed Slide Door 1. Go to the Bottom Rail on the Fixed Sidelite. Locate the Bracket that should be sticking out from underneath.

  • Page 26: Section 14.4: Adjust The Interlocks

    Note: Adjust Interlocks so there is no contact between the Rail and the Interlock. Any contact will cause the Slide Door to bind. 2. Obtain (1) parts bag taped to the Slide Door at the NABCO factory containing (4) Shims. 3. Remove the Interlock on the Sidelite, Strike Stile. Place (1+) shims directly underneath the Interlock. Line up the screw holes.

  • Page 27: Chapter 16: 110 Vac General Wiring

    DANGER “Electrical Installation Manual U30 Control” P/N 15-10596-30 before attempting to powerup the GT1175 Slide Door . Failure to do so may result in damage to the Slide door and/or injury to the installer and will nullify all warranties .

  • Page 28: Chapter 17: Install Weathering

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 6. Insert the Incoming 120 VAC White (Neutral) wire into the Circuit marked “N”. 7. Insert Green (Grounding) wire into the Circuit marked “PE”. 8. Ensure the Slide door system is Grounded for safe and consistent operation.

  • Page 29: Chapter 18: Glazing

    2. Measure (6) inches up from the Pivot End of Bottom Rail, towards the Top Rail. Mark that spot. 4. For each marked spot, place (1) Setting Block (not provided by NABCO) on top of the Base Glass Stops. 5. Place the Glass Panel on top of the Setting Blocks and up against the Vinyl.

  • Page 30: Section 18.3: Complete The 1/4" Glass Stop Flush Glazing

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 Snap-In Base Glass Stop Glass Panel Snap-In Se ng Block Base Glass Stop Snap-In Se ng Base Glass Stop Block Snap-In Base Glass Stop...

  • Page 31: Section 18.4: Dust Protector Hoods (Clean Room Optional)

    Note: All Aluminum Hoods and Vinyl Shields are installed for Clean Room Slide Door Units only and are not manufactured by NABCO. Please call Customer Service for replacement parts at 1-888-679-3319. Note: Aluminum Hoods are installed at the bottom of each Door panel and Transom.

  • Page 32: Chapter 19: Adjustments

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 CHAPTER 19: ADJUSTMENTS SECTION 19 .1: Adjust Horizontal Position of Carrier Attention:  Adjust Preload before adjusting position of Carrier . 1. Breakout the Slide door. 2. Go underneath the Carrier. With a 3/16” Allen Wrench, loosen (2) 3/8-16x1.5”...

  • Page 33: Section 19.3: Adjust The Breakout Magnet

    4. Go to the back edge of Pivot Stile. Reduce Door sag by tightening the 5/16 inch Set Screw with an 5/32 inch Allen Wrench. a. In the event a longer Set Screw is necessary, an optional 1/2 inch Set Screw is supplied by NABCO within the Parts Bag.

  • Page 34: Section 19.5: Adjust The Ball Plunger

    In the event a Sidelite is ajar, swing open the Sidelite about 2 feet, and then fully close it. 8. Check for proper door operation. 9. Test Detection Zone, and One-Way Traffic or Two-Way Traffic. Please refer to P/N C-00109 “GT1175 Slide Door Owners Manual” that has been packed inside the Decal Packet.

  • Page 35: Chapter 21: Pocketed Slide Door Configuration

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 CHAPTER 21: POCKETED SLIDE DOOR CONFIGURATION Attention:  Pocketed slide doors use two Sidelite Panels . Sidelite Panels and Slide Doors are installed the same way as Standard Sidelite Panels and Slide Doors (except where specified) . SECTION 20 .1: Full Open Pocketed Slide Door...

  • Page 36: Section 20.2: Fixed Sidelite Pocketed Slide Door

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 SECTION 20 .2: Fixed Sidelite Pocketed Slide Door INTERIOR POCKET EXTERIOR Step 1: Step 2: Step 3: Install Fixed Sidelite Install Full Open Sidelite Install Slide Door...

  • Page 37: Service Parts: Non-Handed Kit P/N A-00407

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SERVICE PARTS: NON-HANDED KIT P/N A-00407 Full Open Pocketed DN 2318 Full Open 1175 Pocketed Parts Kit: P/N A-00407 Item Part Note Description Used To M-00606 BUSHING, BOTTOM PIVOT, SWING PANEL 2 Protect inside of Barrel from dust/dirt.

  • Page 38: Service Parts: Lh Kit P/N A-00403; Rh Kit P/N A-00618

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 SERVICE PARTS: LH KIT P/N A-00403; RH KIT P/N A-00618 Fixed Sidelite Standard DN 1352 Fixed Sidelite 1175 Parts Kit: LH P/N A-00403 and RH P/N A-00402...

  • Page 39: Service Parts: Non-Handed Kit; Full Open Standard

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SERVICE PARTS: NON-HANDED KIT; FULL OPEN STANDARD Narrow Stile P/N A-00404; Medium Stile P/N A-00405 DN 1353 Full Open 1175 Parts Kit: P/N Narrow A-00404; Medium A-00405 Item Part Note Description Used To M-00606 BUSHING, BOTTOM PIVOT, SWING PANEL 1 Prevent wear and noise.

  • Page 40: Service Parts: Header

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 40 of 62...
  • Page 41 GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 Header Item Part Finish/Sizes/Notes Description T-00061 Zinc FHMS,1/4-20x1.000L.,PHIL,TRI-LOBE,ZINC T-00022 Black Zinc FHMS,1/4-20x1.000L.,PHIL,TRI-LOBE,BLK ZN T-00010 In all Part Bags HHCS,1/4-20x0.750L.,WHIZLOCK,ZINC M-60582 RH/Clear END CAP,ONE PIECE HEADER,RH,204 M-70582 RH/Dark Bronze END CAP,ONE PIECE HEADER,RH,313 M-60574 LH/Clear END CAP,ONE PIECE HEADER,LH,204...
  • Page 42 GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 Header Item Part Finish/Sizes/Notes Description M-01168 24 inches HARNESS,EXTENSION,1175 SENSOR,24” M-02064 38 inches HARNESS,EXTENSION,1175 SENSOR,38” M-01156 48 inches HARNESS,EXTENSION,1175 SENSOR,48” A-00967 36 inches HARNESS;EXTENSION;ROCKER SWITCH;36IN.
  • Page 43 GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SERVICE PARTS: FIXED SIDELITE Viewed from Break Out Side DN 0598 43 of 62...

  • Page 44: Service Parts: Left Hand Fixed Sidelite

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 SERVICE PARTS: LEFT HAND FIXED SIDELITE Viewed from Break Out Side Holding Beam See Header DN 0600 44 of 62...

  • Page 45: Service Parts: Right Hand Fixed Sidelite

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SERVICE PARTS: RIGHT HAND FIXED SIDELITE Viewed from Break Out Side Holding Beam See Header DN 0601 45 of 62...
  • Page 46 GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 Fixed Sidelite Item Part Finish/Sizes/Notes Description M-01144 SWITCH, KEY - NABCO M-01145 SWITCH, KEY - PORTA SERVICE M-00428 SWITCH MODULE,3 ROCKER,NABCO M-00429 SWITCH MODULE,3 ROCKER,PORTA...
  • Page 47 GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SERVICE PARTS: SLIDE DOOR FOR FIXED SIDELITE Viewed from Break Out Side Breakout Side DN 0584 47 of 62...

  • Page 48: Service Parts: Left Hand Slide Door Fixed Sidelite

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 SERVICE PARTS: LEFT HAND SLIDE DOOR FIXED SIDELITE Viewed from Break Out Side Use only when deemed necessary DN 0589 48 of 62...

  • Page 49: Service Parts: Right Hand Slide Door Fixed Sidelite

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SERVICE PARTS: RIGHT HAND SLIDE DOOR FIXED SIDELITE Viewed from Break Out Side Use only when DN 0585 deemed necessary 49 of 62...
  • Page 50 GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 Fixed Sidelite Slide Door Item Part Finish/Sizes/Notes Description A-60133 Clear CARRIER END CAP,204 A-70133 Dark Bronze CARRIER END CAP,313 M-00690 WEATHER, PILE .2 T-00006 Zinc FHSMS,10x0.750L.,PHIL,ZINC...
  • Page 51 GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 Fixed Sidelite Slide Door Item Part Finish/Sizes/Notes Description M-60278 Clear HOLDER,WEATHERING BRUSH,204,EXTRU M-70278 Dark Bronze HOLDER,WEATHERING BRUSH,313,EXTRU M-00274 BRUSH, NYLON, 1” STEPPED M-00698 BRUSH, NYLON, 1.5” T-00105 SHSS,8-32x0.313L.,CUP PT. T-00016 Zinc FHMS,1/4-20x0.438L.,PHIL,UNDERCUT,ZINC T-00108 Black Oxide FHMS,1/4-20x0.438L.,PHIL,UNDERCUT,BLK ZN...
  • Page 52 GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 SERVICE PARTS: FULL OPEN SIDELITE Viewed from Break Out Side Non-Breakout Side DN 1035 52 of 62...

  • Page 53: Service Parts: Left Hand Sidelite Full Open

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SERVICE PARTS: LEFT HAND SIDELITE FULL OPEN Viewed from Non-Break Out Side Holding Beam See Header DN 1037 53 of 62...

  • Page 54: Service Parts: Right Hand Sidelite Full Open

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 SERVICE PARTS: RIGHT HAND SIDELITE FULL OPEN Viewed from Non-Break Out Side Holding Beam See Header DN 2336 54 of 62...
  • Page 55 T-NUT, 3/8”-16, TIE ROD M-00462 CLIP,MUNTIN,.261 HOLE T-00061 FHMS,1/4-20x1.000L.,PHIL,TRI-LOBE,ZINC M-00428 SWITCH MODULE,3 ROCKER,NABCO M-01144 SWITCH, KEY - NABCO M-00606 In Part Bag A-00404 & A-00405 & A-00407 BUSHING, BOTTOM PIVOT, SWING PANEL T-00007 In Part Bag A-00404 & A-00405 & A-00407 FHMS,1/4-20x0.500L.,PHIL,UNDRCUT,F-PT,ZN M-00611 In Part Bag A-00404 &...
  • Page 56 GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 Full Open Sidelite Item Part Finish/Sizes/Notes Description M-60258 THRESHOLD,4-1/2 X 1/2,204,EXTRU T-00008 In Part Bag A-00404 & A-00405 & A-00407 FHSMS,1/4x2.750L.,PHIL,TAPCON,BLUE A-00391 KIT,SHIM,INTERLOCK M-00289...
  • Page 57 GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SERVICE PARTS: SLIDE DOOR FULL OPEN Viewed from Break Out Side Non-Breakout Side DN 1038 57 of 62...

  • Page 58: Service Parts: Left Hand Slide Door Full Open

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 SERVICE PARTS: LEFT HAND SLIDE DOOR FULL OPEN Viewed from Non-Break Out Side Used only when Deemed Necessary DN 1040 58 of 62...

  • Page 59: Service Parts: Right Hand Slide Door Full Open

    GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 SERVICE PARTS: RIGHT HAND SLIDE DOOR FULL OPEN Viewed from Non-Break Out Side 35 36 Used only when DN 1039 Deemed Necessary 59 of 62...
  • Page 60 GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 Full Open Slide Door Item Part Finish/Sizes/Notes Description A-60133 Clear CARRIER END CAP,204 A-70133 Dark Bronze CARRIER END CAP,313 M-00690 WEATHER, PILE .2 T-00006 Zinc FHSMS,10x0.750L.,PHIL,ZINC...
  • Page 61 GT1175StandardandPocketedSlideDoorsInstallationManual;withOpusController Rev.11-12-20 P/NC-00370 Full Open Slide Door Item Part Finish/Sizes/Notes Description T-00016 Zinc FHMS,1/4-20x0.438L.,PHIL,UNDERCUT,ZINC T-00108 Black Oxide FHMS,1/4-20x0.438L.,PHIL,UNDERCUT,BLK ZN A-00198 .090 Narrow Stile NOSE CASTER ASSY, NAR A-00207 .125 Medium Stile NOSE CASTER ASSY, MED T-00025 Zinc NUT,WHIZLOCK,3/8-16,ZINC M-00422...

  • Page 62: Service Parts: Glass Stops And Transom Hardware

    GT1175 Standard and Pocketed Slide Doors Installation Manual; with Opus Controller www.NabcoEntrances.com P/N C-00370 Rev 11-12-20 SERVICE PARTS: GLASS STOPS AND TRANSOM HARDWARE Viewed from Break Out Side DN 0618 Glass Stops and Transom Hardware Item Part Finish/Sizes/Notes Description T-00157 “PHSMS,8x1.000L.,PHIL,TYPE B”...

Table of Contents