Page 1
QUICK START ATEQ F670 Version 1.0 (Photo no contractual) Reference: MR-36300C-U...
Page 2
REVISIONS OF THE ATEQ F670 USER MANUAL Due to continuing improvements, the information contained in this user manual, the features and design of this device are subject to be changed without prior notice. Date Edition/Revision Reference Chapters up dating Week/Year...
Quick start manual TABLE OF CONTENTS TABLE OF CONTENTS ....................1 PREAMBULE........................2 1. DEFINITION OF THE ATEQ F670 ......................2 2. MEASUREMENT CHARACTERISTICS....................2 3. THE MAIN TYPES OF MEASUREMENT....................3 4. THE THREE TYPES OF TEST ......................3 5. MEASUREMENT CYCLE ........................3 INSTALLATION ......................
Quick start - F670 PREAMBULE 1. DEFINITION OF THE ATEQ F670 The ATEQ F670 is a compact air/air TEST DIFFERENTIAL REFERENCE PART SENSOR PART leak detector used to test the air- tightness of parts. The method used is based on the measurement of a...
5. MEASUREMENT CYCLE WAIT FILL STABILIZATION TEST DUMP The measurement cycle consists of 5 phases: Coupling Stabilization Test Dump Cycle Start Fill time time time time time MR-36300C-U Quick start manual ATEQ F670 Page 3/25...
100 / 240 V AC OWER SUPPLY WITH FF SWITCH OPTION Supply the ATEQ F670 with the built in power supply, with a voltage between 100 and 240 V AC - 50 W. I: ON / O: OFF. 2.2. USB...
Page 9
200mA Max Output 5 End of cycle Output 5 End of cycle The compact mode is a software function which is activated in the CONFIGURATION/ AUTOMATISM / CHANGE I/O / OUTPUT menu. MR-36300C-U Quick start manual ATEQ F670 Page 7/25...
Page 10
(input 7) (input 8) (input 9) 17 à 32 33 à 64 65 à 128 With x who takes the 0 or 1 value in function of the program number to be called. MR-36300C-U Quick start manual ATEQ F670 Page 8/25...
Page 11
Input 4 (NPN or PNP)* Pin 14 Ground Analogue outputs Pin 15 Input 5 (NPN or PNP)* Pin 16 Ground * Inputs NPN or PNP following the strap position on the board. MR-36300C-U Quick start manual ATEQ F670 Page 9/25...
The air must be clean and dry. The supply pressure must always be between 4 and 8 bar (400 kPa and 800 kPa). MR-36300C-U Quick start manual ATEQ F670 Page 10/25...
NEUMATICS TEST OUTPUTS These outputs enable parts to be connected (test, reference). The pressurization output is used for the addition of ATEQ accessories (Y valve). Inputs / Outputs on the rear side of the F670: Reference Output R Pressurization Output Test Output T 4.3.
Scroll down or decrease numerical values Opening a menu, entering a parameter, confirmation of a parameter. Return to the previous menu or function, escape without modifying a parameter Programmable key by the user's preferences (see below). MR-36300C-U Quick start manual ATEQ F670 Page 12/25...
Page 15
Program defined: to access directly to the selected program parameters. Run program: to access directly to the current program parameterst (run program). Last results : to access directly to the test results menu. MR-36300C-U Quick start manual ATEQ F670 Page 13/25...
Access to the special cycle's service menu menu Access to the Access to the results menu, programs backup and display parameters Access to the USB Access to the connection configuration menu functions MR-36300C-U Quick start manual ATEQ F670 Page 14/25...
TEST TIME : 2.0 s ◄ value and validate with "OK". DUMP TIME : 0.0 s Press. UNIT: bar Max FILL 0.000 Do the same process for all the others parameters. MR-36300C-U Quick start manual ATEQ F670 Page 15/25...
Note: if no extended function has been activated from the "More Functions" menus, the FUNCTION menu is empty. Edition, duplication, deletion or copy of a test program, program number to start: see the manuals CDROM for further information. MR-36300C-U Quick start manual ATEQ F670 Page 16/25...
Press the RESET key to stop the current measurement cycle. The message "OK" show the device is pending a new test cycle. At the end of the measurement cycle, the test result is displayed. MR-36300C-U Quick start manual ATEQ F670 Page 17/25...
These functions, to appear in the program, must be activated first in the "More functions" menu. Then it must validate and configure it in function menu of the program. Each program can be individually personalized. MR-36300C-U Quick start manual ATEQ F670 Page 18/25...
ATR Learning: cycle to enter ATR parameters; this is to run at each switching on of the device or after a long time without measurement. Volume calculation: cycle to calculate the volume of the test circuit. MR-36300C-U Quick start manual ATEQ F670 Page 19/25...
Miscellaneous: Smart key, to configure the assigned to the "SMART KEY" key. Auto setup, to enables the automatic creation of a simple test program. MR-36300C-U Quick start manual ATEQ F670 Page 20/25...
This is to save on an USB memory key the parameters to recover for later use, device cloning, and program cloning or backup for device reconfiguration. This is running if the parameters are unlocked. MR-36300C-U Quick start manual ATEQ F670 Page 21/25...
1. ACCESSORIES PROVIDED 1.1. 100 230 V AC POWER SUPPLY The power supply cable of the F670 allows its connection to the mains supply network (from 100 to 240V AC). 2. ACCESSORIES IN OPTION Master leaks: the master leaks are used to check the device calibration.
100 à 240 V AC / 2 A Pneumatics connections: 3/5, 4/6 or 6/8 Weight (kg): about 8 Format : 19 inches (3U) +10°C to +45°C Running temperature: Storage temperature: 0°C to +60 °C MR-36300C-U Quick start manual ATEQ F670 Page 23/25...
If all the other checks do not resolve the problem, the instrument’s circuit may be checked. ATEQ does not accept any liability in regard to calibrations and settings to its instruments which are not carried out by its own personnel.
Test Reject .........16 Measurement cycle ......3 Test time..........16 Measurements characteristics ....2 Touches de cycle........12 Minimum fill.........16 Type of test ...........3 More functions menu ......18 USB ............5 Navigation...........11 Navigation keys ........12 Operation fault ........24 MR-36300C-U Quick start manual ATEQ F670 Page 25/25...
Page 28
This document is the exclusive property of ATEQ. It may not be communicated, reproduced or used without prior consent.