Datamax M-Class Mark II Operator's Manual page 48

WLAN
MODE
ENABLED
DI SABLED
BSS
ADDRESS
SI GNAL
READI NGS
I P ADDRESS
SUBNET MASK
GATEWAY
SNMP TRAP
DESTI NATI ON
I P DI SCOVERY
ENABLED
DI SABLED
SNMP
ENABLED
DI SABLED
ADVANCED
TELNET
FTP
MTU
GRATUI TOUS
ARP
TCP
KEEPALI VE
ENABLED
DI SABLED
PORT
NUMBER
DUPLEX
CAPABI LTY
ADVERTI SE
CAPABI LI TY
NETWORK
REPORT
SET FACTORY
DEFAULTS
Ch a pt e r 4 – M e n u Syst e m
Cont rols t he com m unicat ions set t ings for t he net work int erface, where:
Select s bet ween wired and wireless operat ion, where:
Enables t he wireless int erface. ( This is t he Default Set t ing.)
Enables t he wired int erface.
Specifies t he radio m odule's st at ic I P address; up t o four oct et s separat ed by a
period. I f Enable DHCP is checked, t his param et er is ignored. Default is 0.0.0.0.
Provides a graphical represent at ion of Signal St rengt h ( in dBm ) , Noise Level ( in
dBm ) , and Qualit y.
Specifies t he st at ic I P Address of t he int erface in t he st andard oct et form at .
Specifies t he st at ic Subnet assigned t o t he int erface, for exam ple:
255.255.255.000.
Specifies t he Gat eway Address t he int erface will use, for exam ple:
010.001.001.001.
Specifies t he net work I P Address where SNMP t raps will be sent when SNMP service
is inst alled on your receiver. I f zeroed, no t raps are sent .
Set s t he address discovery m et hod, where:
The card broadcast s over t he net work t o receive addresses from t he responsible
server at st art up. Manual m odificat ions t o I P Address, Subnet Mask, or Gat eway
Address are not allowed; and, if no server is found, t he specified st at ic value will be
used. ( Default Set t ing)

A server assigned I P address t akes precedence over any st at ic I P
address st ored in t he int erface.
The st ored st at ic I P, Subnet Mask, and / or Gat eway Address will be used.
Set s SNMP
( Default Set t ing)
Advanced set t ings for t he NI C Card.
Enable/ Disable Telnet prot ocol
Enable/ Disable FTP prot ocol
Set s t he Maxim um Transm ission Unit packet size, where:
Packet size, in byt es. ( 512- 65515) ; Default is 1500
Set s t im e int erval for ARP t ransm ission packet s, where:
( 0- 2048 m inut es) ; Default is 0
Allows m onit oring of an open connect ion t o det ect any disconnect s not properly
closed, including reset access point s and unplugged print ers, where:
Keeps m onit oring act ive.
Closes such a disconnect ion aft er 2.5 m inut es. ( Default Set t ing)
Select s t he Port t o use for all net work com m unicat ions; Default is 9100
Specifies t he t ransm ission and speed of t he wired Et hernet connect ion:
•
Aut o- Negot iat e ( default ) ;
•
100 BaseT Full Duplex;
•
100 BaseT Half Duplex;
•
10 BaseT Full Duplex; or,
•
10 BaseT Half Duplex
Select s t he m et hod in which t he Duplex Capabilit y set t ing is advert ised, where:
•
Aut om at ic ( advert ises t he DUPLEX CAPABI LI TY set t ing) ; or,
•
All Capabilit ies ( advert ises all capabilit ies)
Print s or displays a report which list s t he print er's net work set t ings.
Reset s NI C Adapt er param et ers t o t he fact ory default s values.
4 2