Safety Information For Installation; Safety Information For Electrical Connection; Safety Information For Initial Start-Up; Unit Description - Webasto Pure Installation Instructions Manual

3 | Unit description

2.3

Safety information for installation

n Installation and connection of the charging station
must only be carried out by an electrician.
n Only use the supplied installation material.
n The Webasto Pure safety concept is based on a power
supply system that is earthed at all times. The electri-
cian must ensure this requirement during installation.
n The charging station is suitable for use in areas without
access restrictions.
n Do not install the charging station in an explosion
sensitive area (EX zone).
n Install the charging station in such a way that the char-
ging cable does not block any passageways.
n Do not install the charging station in areas subject to
ammonia or air containing ammonia.
n Do not install the charging station in a location where
falling objects (e.g. extension reel or tyres) can damage
the charging station.
n The charging station is designed for use indoors, e.g.
garages as well as for use in protected outdoor areas,
e.g. carports. Do not install the charging station in the
vicinity of water jets, e.g. car wash installations, high
pressure cleaners or garden hoses.
n The charging station shall not be exposed to direct rain
to prevent damage due to freezing, hail or similar.
n Protect the charging station from direct sunlight. The
charging current may be reduced at high temperatures
or charging may be disabled completely.
n The installation location of the charging station should
be selected such that vehicles cannot inadvertently col-
lide with it. Protective measures must be implemented
if the possibility of damage cannot be ruled out.
n Do not place the charging station into operation if it is
damaged during installation. A replacement will be re-
quired.
2.4 Safety information for electrical
connection
n Comply with the nationally applicable requirements
pertaining to electrical installations, fire protection,
safety regulations and escape routes at the intended
installation location. Observe the applicable national
installation regulations.
n Each charging station must be protected with its own
line circuit breaker and residual current circuit breaker.
See chapter 7.1, "Requirements at the installation loca-
tion" on page 5.
n Make sure that the electrical connections are de-ener-
gised before connecting the charging station to the
power supply.
n Do not connect a vehicle during initial start-up of the
charger.
n Make sure that the correct supply cable is used for the
power connection.
n Do not leave the charging station unattended with the
cover open.
n Do not install the charging station without the mount-
ing frame.
n Change DIP-switch settings only with the power off.
n Register with the power supply company as required.
4 / 13
2.5 Safety information for initial start-
up
n Initial start-up of the charging station must be carried
out only by an electrician.
n Prior to initial start-up, the electrician must check that
the charging station has been connected correctly.
n Before starting-up the charging station, check the
charging cable, charging coupling and the charging
station for visible damage. The charging station must
not be started up if it is damaged or if the charging
cable/charging coupling is damaged.
3 Unit description
These operating and installation instructions describe the
Webasto Pure charging station. The exact unit description is in-
dicated on the type label of the charging station.
Fig. 1
4

Transportation and storage

Observe the ambient temperature for storage during transporta-
tion. See chapter 13, "Technical data" on page 11.
Transport the charging station only when suitably packaged.
5

Scope of delivery

Scope of delivery
Charging station with pre-assembled charging
cable
Mounting frame
Key
Installation kit for wall mounting
n Wall plug (8 x 50 mm, Fischer UX R 8)
n Screw (6 x 70, T25)
n Screw (6 x 90, T25)
n Washer (ISO 7089-8,4)
Operating and installation instructions
u
Take the charging station and the mounting frame from the
package.
u
Check the completeness of the delivery.
u
Check the complete delivery for damage.
6

Required tools

Tool description
Slot-head screwdriver 0.5x3.5 mm
Torx screwdriver Tx25
Torx screwdriver Tx10
Drilling machine with 8 mm drill
Mounting tools for 8 mm plugs and screws
WCH000002A
Amount
1
1
2
4
2
2
4
1
Amount
1
1
1
1
1
II Webasto Pure EN