Positioning Of The Child; Removing And Refitting The Cover - BESAFE iZi Turn B i-Size User Manual

12
18.
Tip: For an optimal height of the SIP+, position it between the two raised
dots on the side of the seat shell.
19.
Do not use the SIP+ on the seat when the space between seat and door
of the vehicle is too small, which might lead to a situation where the
seat is not positioned correctly on the vehicle seat. (6)
Removal of the seat from the vehicle
1.
To remove the seat from the vehicle, turn the seat rear facing and push the
seat upwards while adjusting the floor support to its shortest length.
2.
Release the ISOfix connectors out of the seat by pushing down the switch
for the ISOfix connectors on both sides. Pull the ISOfix release switch on
both sides to disconnect from the ISOfix car anchorage.

Positioning of the child

1. Turn the seat towards the door while you pull the rotation release handle
upwards.
2. Check that the shoulder strap slots are level with your child's shoulders. (7)
3. While pressing the button of the central adjuster, pull the shoulder straps
away from the seat with a flat hand. Make sure to pull the straps evenly so
that they stay at the same length. (8)
4.
Open the harness buckle. (9)
5.
The height of the shoulder straps and the headrest can be adjusted by
pulling the release handle upwards at the back of the headrest and pulling
the headrest up or down. (10)
6.
Position the shoulder straps over the marking at the sides of the seat to
use the magnets to keep the harness open while you position the child. (11)
7.
When the child is positioned, place the shoulder straps over the child's
shoulders and close the buckle: CLICK! (12)
8.
Pull the harness strap through the central adjuster in the direction of
the arrow straight up/forwards. Continue pulling until the harness is a
comfortable but a firm fit. (13)
9.
Turn the seat against or with the driving direction before driving and check
if the release handles show green and the seat is locked into the driving
direction. (14)
Baby insert
1. The baby insert must be used from birth and can be used until a stature
height of 87 cm. Don't take the baby insert out before the baby can sit
upright by itself.
2. The baby insert can be taken out of the seatshell, by guiding the harness
through the slots of the baby insert.
3.
The baby insert can be positioned back in the seatshell, by guiding the
harness through the slots of the baby insert. Use the baby insert only
in the most reclined position of the seat. Make sure the harness is
positioned correct, so the harness can be pulled tight without twisting.
(15)
Baby cushion
1.
The baby cushion offers extra comfort for young babies.
2.
< 60 cm (16)
3.
> 60 cm (17)

Removing and refitting the cover

• Do take care when you remove the cover, as re-fitting the cover is done
in reverse.
• The cover of the headrest can be taken off separately by disconnecting
the beads at the back and pulling off the fabric towards the front.
! Warning: potential misuse
•
The child seat MUST NOT be installed in a front passenger
seat WITH AN ACTIVATED AIRBAG.
•
The floor support must always be used. Make sure that
the floor support is fully pushed down and that the seat is
positioned horizontal with the spirit level in the middle.
•
Never drive with a child in the seat if the seat is rotated to the side.
•
Make sure the indicators are green before you drive.
Guarantee
•
Should this product prove faulty within 24 months of purchase due to
materials or manufacturing fault, except covers and harness straps,
please return it to the original place of purchase.
•
The guarantee is only valid when you use your seat appropriately and
with care. Please contact your retailer, they will decide if the seat will be
returned to the manufacturer for repair. Replacement or return cannot be
claimed. The guarantee is not extended through repair.
• The guarantee expires: when there is no receipt, when defects are caused
by incorrect and improper use, when defects are caused by abuse,
misuse or negligence.
13