Related Manuals for BESAFE iZi Plus
Summary of Contents for BESAFE iZi Plus
- Page 1 REARWARD-FACING USER MANUAL ECE R44 04 GROUP WEIGHT 0+/1/2 0-25 kg 6m-5y...
-
Page 2: Table Of Contents
Thank you for choosing BeSafe iZi Plus BeSafe has developed this seat with much care, to protect • The harness straps must always be locked when the child is in your child during the first phase of her or his life. the seat. • The harness straps must be tightened without slack and not ! It is important that you read this user manual BEFORE twisted. You should not be able to get more than one finger installing your seat. Incorrect installation could endanger between the harness and your baby (2cm). your child. • The cover of the shoulder strap contains magnets. Magnets can influence electronic equipment such as pacemakers. • The floor support must always be used. Make sure that the floor Contents support is fully pushed down. • We recommend that this seat is used only for children who can Vital information sit upright, so not younger than 6 months. Rearward-facing belt installation • For children under 1 year and/or under 10 kg weight, we Removing the seat recommend that the most reclined sitting position and the body Positioning the child hugger and seat cushion are used. Sleeping position • Remove the baby cushion (extra available accessory) when the Removing and refitting the cover child is older then 1 year. Cleaning instructions • Remove the body hugger when the child is older then 2 years. Warning: potential misuse • When the child weighs over 25 kg or the shoulders are higher... -
Page 3: Rearward-Facing Belt Installation
13. Floor support height indicator Installation on the front seat 14. Anchor belt (2x) 15. Release handle head rest • Join the 2 anchor belts together to make a single belt. Put the 16. Floor support position indicator lock of belt 2 through the loop of the belt 1 and then through the 17. Connector for anchor belt (2x) loop of belt 2. Pull it firmly. (21) • Put the middle part of the anchor belt over the inner part of the vehicle seat. Bring the two ends of the anchor belt under the ! It is NOT ALLOWED to mount the seat in a front front seat of the vehicle and bring them upwards to the seat. passenger seat WITH AN ACTIVATED AIRBAG. (22) 1. When mounting in the front seat of the vehicle, adjust the back • If these methods do not work in your car refer to rest of this vehicle seat in an upright position. When mounting www.besafe.com for alternatives. in the back seat of the vehicle, push the front seat of the vehicle forward as much as possible. 2. Install the front brace by sliding the two pins in the oval tube under the front side of the seat. Move the front brace inwards with the ratchet. The ratchet is used to adjust the front brace in both directions. Slide the knobs (see red circle) on the ratchet up or down to change direction. (18) 3. Fold down the floor support before you install the seat in your vehicle. (19) - Page 4 With the anchor belts in place the installation can continue: 1. Place the seat sideways into the car with the front brace 15. The height indicator of the floorsupport shows green when the towards you. floor support is in contact with the floor. (29) 16. If you are installing against the dashboard and the seat is not 2. Turn the seat into the right position (with the front brace against the back rest). in contact with the dashboard yet, release the anchor belts and 3. Position the floor support around 5cm. above the floor. position the floor support to the shortest length. 4. The height indicator of the floor support shows grey when 17. Tighten the anchor belts again till the seat is in contact with the floor support is above the floor. (23) the dashboard. 5. In the front seat of the vehicle, you should position the seat 18. Adjust the floor support so it is in contact with the floor of against the dashboard. If it is not possible to obtain contact the vehicle. with the dashboard, position the front seat of the vehicle 19. Positioned in the back seat of the vehicle, you should, if possible, push the front seat of the vehicle backwards, so that as far as possible backwards, preferable with a minimum it is in contact with the child seat. If it is not possible to obtain...
-
Page 5: Removing The Seat
Removing the seat Positioning the child 1. If the seat is installed in the back seat of the vehicle, push the 1. Position of the shoulder straps: Check that the shoulder strap slots are leveled with or or a bit under your child’s shoulders. front seat of the vehicle forward as much as possible. 2. Move the front brace inwards with the ratchet. • too high (32) 3. Move the floor support to the highest position. • correct (33) 4. Release the anchor belts. 2. The height of the shoulder straps and the head rest can be 5. Remove the car belt from the front brace and the seat base. adjusted by releasing the release handle at the back of the 6. Pull the seat back towards the front. Turn the seat so you can head rest and pulling the head rest up or down while keeping easily remove the seat. the head rest upright. (34) 7. Remove the anchor belts from the vehicle. 3. Pull the shoulder straps up while pressing the button of the central adjuster. (35) 4. Open the harness buckle. 5. Position the shoulder straps over the orange marking at sides of the seat to keep the harness open while you position the child. (36) 6. -
Page 6: Removing And Refitting The Cover
• Pull the head rest in the highest position. Mount the head rest • DO NOT use the seat without tightening the anchor belts when cover and connect the hooks at the back side. Pull the harness mounted rearward-facing. straps through the holes. Connect the loose bottom part of the head rest fabric with the plastic part under the head rest. ! Important advice • Pull the harness straps through the opening of the seat cover and lock the harness buckle. Pull the crotch strap through the opening of the seat part. • DO NOT attempt to dismantle, modify or add any part to the • Mount the top part and then the shoulder parts. Mount the seat. Warranty will expire if non-original parts or accessories seat part and bring the seat cover under the rear parts of the are used. sidewalls. • DO NOT use anything, such as a cushion, to raise the child seat off the passenger seat of the vehicle. In an accident the seat will not be able to protect your child in the right way. Cleaning instructions • Never leave your child unattended in the seat. • Make sure all passengers are informed about how to release • The fabric covers shall be washed according to the your child in case of emergency. instructions on the inside of the covers. • An unoccupied child seat should always be fastened in • Clean harness by hand with water and mild soap. the vehicle. • DO NOT use any aggressive cleaning products; these may • Make sure luggage or other objects are properly secured. harm the construction material of the seat. Unsecured luggage may cause severe injuries to children and adults in case of accidents. • Never use the seat without the cover. The cover is a safety feature and may only be replaced by an original BeSafe cover. • Under the cover we use EPS foam. Do not push or pull too hard against the foam, since you might damage the foam. -
Page 7: Guarantee
Guarantee • Do not use any aggressive cleaning products; these may harm • All BeSafe products are carefully designed, manufactured and tested. All of our BeSafe child seats are tested periodically the construction material of the seat. out of our continuous production in our test laboratory. • BeSafe advises that child seats should not be bought or sold Furthermore they are tested by independent test institutes. second-hand. • Should this product prove faulty within 24 months of purchase • KEEP this user manual for later use with the seat. due to materials or manufacturing fault, except covers • DO NOT use at home. It has not been designed for home use and harness straps, please return it to the original place and can only be used in a vehicle. of purchase. • The guarantee is only valid when you use your seat Practical advice appropriately and with care. Please contact your dealer, he When the child seat is mounted in the car check all the areas where will decide if the seat will be returned to the manufacturer the child seat might touch the interior. We recommend using a for repair. Replacement or return cannot be claimed. The (BeSafe) protection cover in these places to avoid cuts, marks or guarantee does not get extended through repair. discolouration on the interior of the vehicle, especially in vehicles • The guarantee expires: when there is no receipt, when defects are caused by wrong and improper use, when defects are with leather or wooden interior. caused by abuse, misuse or negligence. Point of sale information Notice for REARWARD-FACING installation • This is a semi-universal Child Restraint System. It is approved to regulation No. 44.04, series of amendments for general...