Page 1
User manual 0+/1 www.besafe.eu ECE R44/04 Complies with revised standard: SEMI-UNIVERSAL O-18 KG UNIVERSAL 9-18 KG ECE R44/04 ECE R44/04 Tested and Approved R 44 04201 (SEMI-UNIVERSAL) R 44 04202 (UNIVERSAL)
REARWARD FACING Removing FORWARD FACING Installation Sitting positions Car seat protection After an accident Guarantee Removing and refitting the cover Important advice Point of sale information Second-hand car seats BeSafe advises that child seats should not be bought or sold second-hand.
ISOfix anchorage points. When iZi Combi ISOfix is installed forward facing, the 3-point-belt has to be used. BeSafe iZi Combi ISOfix is approved in groups 0+ and 1, rearward-facing from 0-18 kg and group 1 forward-facing, from 9-18 kg.
Preparing to install Crucial parts 1. Internal harness 2. Harness adjustment Front brace Switch for ISOfix connectors 5. Lever for sleeping positions 6. Ratchet for front brace 7. ISOfix connectors 8. Release button for ISOfix connectors 7. ISOfix installation connectors 9.
Page 5
Height can be adjusted by releasing the height adjustment device on the back of the iZi Combi ISOfix, place it in the correct position and clicking it in. Twist and pull the shoulder belts on the front side of the seat until the belts are adjusted into the correct position.
If your car is not epuipped with ISOfix insertion clips (16), insert these to make installation easier. You can find the ISOfix insertion (16) clips under the base of your iZi Combi ISOfix. Clip the insertion clips into the anchorage points.
Page 7
Remove the plastic caps (9) from the ISOfix connectors (7) by pressing down the ISOfix release button (8). Use the ratchet (6) to adjust the front brace to the inmost position. The ratchet (6) is used to adjust the front brace in both directions.
Page 8
The BeSafe iZi Combi ISOfix can ONLY be installed rearward facing in cars with ISOfix anchorage points. The BeSafe iZi Combi ISOfix must not be used in the front passenger seat without deactivating the airbag. BeSafe iZi Combi ISOfix is installed the same way in the front and back seat.
Page 9
Pull both ISOfix connectors (7) as far out as possible. The switch (4) then goes into the lowest position and locks the connectors (7). Click the ISOfix connectors in the ISOfix anchorages. Click Make sure that the two indica- tors (10) are green, both in the hole and on the inside of the release gear.
Page 10
Adjust the front brace outwards with the ratchet (6). Continue tightening until the brace is pressed well into the backrest of the car seat. If possible, push the front seat backwards so that it is in contact with the child seat. If it is not possible to obtain contact with the child seat, push the backrest of the front seat forward so that the distance between child seat and backrest is minimum 25 cm.
NEVER use BeSafe iZi Combi ISOfix without tightening the front brace when mounting rearward facing. ALWAYS make sure that the indicator for correct installation of the ISOfix anchorages shows GREEN. NEVER USE iZi Combi ISOfix on a passenger seat fitted with activated frontal airbag.
Page 12
REARWARD FACING - Removing the iZi Combi ISOfix If your iZi Combi ISOfix is installed in the back seat, push the front seat as far forward as possible. Adjust the backrest as far backwards as possible, when removing from the front seat.
Page 13
Push the switch (4) on each side, and push the ISOfix installation connectors (7) into the base. Pull the iZi Combi ISOfix back towards the front seat. Turn the seat so you can easily remove the seat. Remove your iZi Combi ISOfix from the car.
The BeSafe iZi Combi ISOfix can ONLY be installed forward- facing in cars with 3-point belt. The BeSafe iZi Combi ISOfix must not be used in the front passenger seat without deactivating the airbag. To mounting the BeSafe iZi Combi in forward-facing, remove the front brace (3).
Page 15
Pull out the seat belt, place the hip belt over the bottom base of the iZi Combi. Pull the hip belt over the metal hook and fasten the belt. Click! Guide the shoulder belt through the belt housings (17)at the top of each side of the child seat.
Page 16
Pull the shoulder belt through both belt housings and close the clamps. The seat belt is now locked in position. It is very important that the belt clamps are properly locked. Use the rachet lever (5) to tighten the seat properly. Check that the iZi Combi is firmly fixed, if not, repeat the prosedure from the beginning.
Page 17
9 kg. NEVER use the iZi Combi forward facing installation without tighten the seat properly. Always check that the iZi Combi is firmly fixed. NEVER USE iZi Combi ISOfix on a passenger seat fitted with activated frontal airbag.
Sitting positions BeSafe iZi Combi ISOfix has 4 sitting positions. The sitting positions can be regulated by using the lever (5) Car seat protection To avoid damage to the fabric of the car seat, especially with leather car seats, protect your car...
After an accident, the iZi Combi ISOfix must be replaced. Although it may look undamaged, if you were to have another accident, the iZi Combi ISOfix may not be able to protect your child as well as it should. Guarantee All BeSafe products are carefully designed, manufactured and tested.
Removing and refitting the cover Never use the iZi Combi ISOfix without the cover. The cover is part of the system and may only be replaced by an original iZi Combi ISOfix cover. ALWAYS use the child safety belt provided with the iZi combi ISOfix.
Page 21
Washing instructions The cover of the iZi Combi ISOfix must be washed in accordance with the instructions (on the inside of the cover). Cleaning harness and seat DO NOT use any cleaning products; these may harm the construction material of the iZi Combi ISOfix.
Combi ISOfix cover. The cover of the iZi Combi ISOfix must be washed in accordance with the instructions. Do not use any aggresive cleaning products; these may...
Page 23
Combi ISOfix will not be able to protect your child as well as it should. DO NOT use the iZi Combi ISOfix for longer than 5 years. Due to ageing, the quality of the material may change. DO NOT use at home. It has not been designed for home use and can only be used in a car.
The mass group and the ISOfix size class for which this device is intended is: C The iZi Combi ISOfix is suitable for fixing into the seat positions of the cars listed in the appendix ‘carlist’. Seat positions in other cars may also be suitable to accept this child retraint.