Table of Contents
Advertisement
Note
f [BLACK LEVEL ADJUST] is a function that makes the increased brightness in black level of the overlapping image area difficult to
notice when [EDGE BLENDING] is used to structure a multi-display screen. The optimal point of correction is set by adjusting [NON-
OVERLAPPED BLACK LEVEL] so that the black level of the overlapping image area will be the same level as the non-overlapping area. If
the border area of the part where the image is overlapping and the non-overlapping part gets brighter after adjusting [NON-OVERLAPPED
BLACK LEVEL], adjust the width or the shape of the top, bottom, left, or right. Adjust [BLACK BORDER LEVEL] when the adjustment makes
only the border area darker.
f The joining part may look discontinuous depending on the position you are looking from when a screen with high gain or rear screen is used.
f When configuring multiple screens using both horizontal and vertical edge blending, adjust [OVERLAPPED BLACK LEVEL] first before
making adjustments in Step 14). Adjustment method is same as the procedure of [NON-OVERLAPPED BLACK LEVEL].
f If only horizontal or vertical edge blending is used, set all items in [OVERLAPPED BLACK LEVEL] to 0.
f The [AUTO TESTPATTERN] setting changes synchronizing with [AUTO TESTPATTERN] of [COLOR MATCHING].
f Adjustment of the shape of the border between [NON-OVERLAPPED BLACK LEVEL] and [BLACK BORDER LEVEL] is a function to
perform the edge blending together with the adjustment of [GEOMETRY] (x page 115). If [NON-OVERLAPPED BLACK LEVEL] is
deformed by correcting the distortion of the projected image with [GEOMETRY], perform the adjustment following Step 19) to Step 27), and
adjust the edge blending according to the shape of [NON-OVERLAPPED BLACK LEVEL].
f An error is accumulated by repeatedly adjusting the position of the adjustment points, which may distort the shape of the border awkwardly.
In such a case, initialize the shape of the border. Initializing the shape of the border will reset the shape to the factory default (unadjusted
state). For details, refer to "Initializing the shape of the border" (x page 125).
Initializing the shape of the border
Initialize the data adjusted with [UPPER FREE SHAPE], [LOWER FREE SHAPE], [LEFT FREE SHAPE], and
[RIGHT FREE SHAPE] and restore to the factory default settings (unadjusted state).
1)
Press as to select [EDGE BLENDING].
2)
Press qw to select [ON] or [USER].
3)
Press the <ENTER> button.
f The [EDGE BLENDING] screen is displayed.
4)
Press as to select [BLACK LEVEL ADJUST].
5)
Press the <ENTER> button.
f The [BLACK LEVEL ADJUST] screen is displayed.
6)
Press as to select [UPPER FREE SHAPE], [LOWER FREE SHAPE], [LEFT FREE SHAPE], or [RIGHT
FREE SHAPE] to initialize.
7)
Press the <ENTER> button.
f The [UPPER FREE SHAPE] screen, the [LOWER FREE SHAPE] screen, the [LEFT FREE SHAPE]
screen, or the [RIGHT FREE SHAPE] screen is displayed.
8)
Press as to select [INITIALIZE].
9)
Press the <ENTER> button.
f The confirmation screen is displayed.
10) Press qw to select [EXECUTE], and press the <ENTER> button.
Note
f The adjustment data for [UPPER FREE SHAPE], [LOWER FREE SHAPE], [LEFT FREE SHAPE], and [RIGHT FREE SHAPE] cannot be
initialized at once.
f To initialize all the adjustment data, select each item and execute [INITIALIZE] individually.
f When the projector is initialized by one of the following methods, all data in [UPPER FREE SHAPE], [LOWER FREE SHAPE], [LEFT FREE
SHAPE], and [RIGHT FREE SHAPE] are initialized.
g When initialized by selecting the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY RESET]
g When initialized by setting the [PROJECTOR SETUP] menu → [INITIALIZE] → [USER SETTINGS] → [OTHER USER SETTING] to
[INITIALIZE]
[FRAME RESPONSE]
Set the processing method of the image frame delay.
1)
Press as to select [FRAME RESPONSE].
2)
Press qw to switch the item.
f The items will switch each time you press the button.
Chapter 4 Settings — [ADVANCED MENU] menu
ENGLISH - 125
Advertisement
Table of Contents
