Subscribe to Our Youtube Channel
Related Manuals for Panasonic PT-RZ475
Summary of Contents for Panasonic PT-RZ475
- Page 1 PT-RZ475 P ro d u c t N u m b e r : ™ Projector P ro d u c t N a m e : As of May 2013. Specifications and appearance are subject to change without notice.
-
Page 2: Specifications
PT-RZ475 ™ Projectors Specifications Main unit Power supply 100 – 240 V AC, 5.0 – 1.8 A, 50/60 Hz Power consumption 430 W (440 VA) (230 W* with set to /Eco1, LIGHT POWER NORMAL 170 W* with set to Eco2. 0.5 W with... - Page 3 PT-RZ475 ™ Projectors COMPUTER (RGB) IN D-sub HD 15-pin (female) × 1 R, G, B R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD/VD, SYNC: TTL, high impedance, positive/negative automatic NOTE: HD/SYNC, and VD terminals do not accept tri-level sync signals.
- Page 4 PT-RZ475 ™ Projectors Dimensions unit : mm (inch) NOTE: This illustration is not drawn to scale. 455 (17-29/32) Terminals LAN / DIGITAL LINK connector HDMI input DVI-I input Computer input Video input Audio input Audio output Serial input 3D SYNC output...
-
Page 5: Standard Setting-Up Position
PT-RZ475 ™ Projectors Standard setting-up position NOTE: Illustrations show the projector installed Upper edge of projected image using optional ceiling mount bracket ∅60.5 ET-PKR100H. (∅ 2-3/8) This illustration is not drawn to scale. * Adjustable in 40 mm (1-9/16 in) steps. - Page 6 PT-RZ475 ™ Projectors Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:9 L (m) = (diagonal screen size in inches) × 0.0180 – 0.0476 NOTE: Distances calculated with the above equations will include a slight error.
- Page 7 PT-RZ475 ™ Projectors List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning fre- quencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of 162 MHz maximum can be input.
- Page 8 PT-RZ475 ™ Projectors List of compatible 3D signals The 3D signals that can be input to this projector are shown in the table below. Display mode Display Scanning Dot clock HDMI DVI-I Computer frequency resolution frequency Frame Side by Top and...
-
Page 9: Basic Format
PT-RZ475 ™ Projectors Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control. I1 I2 P1 P2 ... Pn Start (2 byte) - Page 10 PT-RZ475 ™ Projectors Control commands Command : Parameter Function Callback POWER (STANDBY) IIS:DL1 DIGITAL LINK IIS:DL1 INPUT SELECT IIS:HD1 HDMI IIS:HD1 IIS:DVI IIS:DVI IIS:RG1 COMPUTER IIS:RG1 IIS:VID VIDEO IIS:VID When DIGITAL LINK input is IIS: DL1:HD1 HDMI 1 IIS:DL1:HD1 selected and input of the...
- Page 11 PT-RZ475 ™ Projectors Status request commands Command : Parameter Function Callback Description Standby power status Input signal status DIGITAL LINK HDMI Computer VIDEO Input signal status of the digital DL1:HD1 HDMI 1 interface box ET-YFB100G when DL1:HD2 HDMI 2 DIGITAL LINK input is selected.
- Page 12 PT-RZ475 ™ Projectors Notes on projector placement and operation Please observe the following precautions for projector placement and operation. Never place objects on top of the projector while it is operating. Make sure there is an unobstructed space of 500 mm (1 foot 8 inches) or more around the projec- tor’s exhaust openings.
Need help?
Do you have a question about the PT-RZ475 and is the answer not in the manual?
Questions and answers