King gates ELEVO620 Instructions And Warnings For Installation And Use page 45

13.1 - SELECTION OF DEVICE CONNECTED
TO "LOCK/AUX" OUTPUT
Default = electric lock
This procedure allows for setting the "AUX" output for the
operation as:
ELECTRIC LOCK: the control unit closes the AUX contact
(terminals 11-12) whenever a command is received.
By default, the contact is closed for 3 seconds (electric lock mode).
COURTESY LIGHT: the control unit closes the AUX contact
(terminal 11-12) whenever a radio command is received (the AUX
button must be programmed – see Paragraph 5.2). By default, the
command is monostable.
m
To control the AUX output when it has been set as a
courtesy light output, you need to register a transmitter
by following the procedure in paragraph 5.2 and connect a
suitable relay.
1. PRESS START BUTTON FOR 3 SECONDS: All the LEDs turn off
(if not, consult Paragraph 14.1)
2. PRESS THE RADIO BUTTON FOR 1 SECOND
• If the yellow "Set" LED is on AUX = Electric lock (if the
setting is correct, go to Point 4; if not, proceed to Point 3).
OR
• If the red "Error" LED is on in fixed mode AUX = Courtesy
light (if the setting is correct, go to Point 4; if not, proceed
to Point 3).
3. PRESS THE RADIO BUTTON FOR 1 SECOND: the red "radio"
LED remains on in fixed mode and the "Error" and "Set" LEDs
light up according to the selected function
4. PRESS THE SET AND RADIO BUTTONS SIMULTANEOUSLY OR
WAIT 10 SECONDS TO EXIT THE PROCEDURE: The LEDs return
to the normal operation configuration
13.2 - SELECTION OF THE TYPE OF DEVICES
CONNECTED TO "S1 EDGE"
Default = "S1 Edge" set for devices with normally closed contact
(terminal 9)
This procedure allows for setting the "S1 Edge" output for
managing 8.2kOhm resistive edges.
The control unit constantly verifies the integrity of the edge by
measuring the resistance between the two dedicated terminals.
1. PRESS START BUTTON FOR 3 SECONDS: All the LEDs turn off
(if not, consult Paragraph 14.1)
2. PRESS THE START BUTTON FOR 1 SECOND:
• If the yellow "Set" LED is on "S1 Edge" = resistive edge
(if the setting is correct, go to Point 4; if not, pro- ceed to
Point 3)
OR
• If the yellow "Set" LED is off "S1 Edge" = device with
normally closed (NC) con- tact (if the setting is correct, go
to Point 4; if not, proceed to Point 3)
3. PRESS THE START BUTTON FOR 1 SECOND: the red "error"
LED lights up in fixed mode and the "Set" LED turns on / off
according to the selected function
4. PRESS THE SET AND RADIO BUTTONS SIMULTANEOUSLY OR
WAIT 10 SECONDS TO EXIT THE PROCEDURE: The LEDs return
to the normal operation configuration
m
In order to carry out the check on the safety devices,
the connected edges must be of the resistive type with 8.2
kOhm.
14 - OTHER FUNCTIONS
To interrupt the following programming sequences at any time,
press the SET and RADIO buttons simultaneously or wait 10
seconds.
14.1 - ACTIVATING/DEACTIVATING THE
CONTROL UNIT PROTECTION DEVICE
Default = control unit protection device not active
This programming sequence allows for locking all control unit
programming sequences and the settings adjustable through the
trimmer.
To perform a new programming sequence or make a dip-
switch/trimmer modification effective, the protection must be
deactivated.
1. PRESS START BUTTON FOR 3 SECONDS: All the LEDs turn off
2. PRESS BOTH BUTTONS START AND RADIO, FOR 2 SECONDS
• If the yellow led "Set" and the red led "Radio" are ON:
central unit lock = enabled (if it is the correct setting, go to
step 4, otherwise proceed to step 3)
OR
• If the yellow led "Set" and the red led "Radio" are OFF:
central unit lock = disabled (if it is the correct setting, go
to step 4, otherwise proceed to step 3)
3. PRESS BOTH BUTTONS START AND RADIO, FOR 2 SECONDS:
the "set" and "radio" LEDs turn on / off according to the
selected function
4. PRESS THE SET AND RADIO BUTTONS SIMULTANEOUSLY OR
WAIT 10 SECONDS TO EXIT THE PROCEDURE: The LEDs return
to the normal operation configuration
14.2 - ENABLE STOP ON PHOTO INPUT
DEFAULT = the automation stops in both opening and closing
when the photocell intervenes, reopening the door when the
photocell is released
1. Press the START button for 3 seconds: all the LEDs go off (if
not, see paragraph 14.1)
2. Press the SET key for 1 second, the red "radio" LED indicates
the function of input S2 (FOT1)
- LED off: the automation stops in both opening and closing
when the photocell is activated, reopening the door when the
photocell is released
- LED on: when the photocell intervenes during closing, the
automation reopens immediately
3. Press the RADIO button for 1 second to change the currently
set function
- 43 - - 43 -