Electrolux Combi TOUCH User Manual page 57

Anom- Type of
Description
aly anomaly
EtUb Stops Boiler
boiler overtemperature
cycles
EtUC Stops the Cavity
oven overtemperature
FA8H After Oven worked 8 hours
ending without air inlet filter
cooking
cycle,
stops oven
cooking
FDXX Lower cavity motor
Stops
(XX = oven failure
00 - 17)
FILS Stops Water boiler level not
boiler reached in time
cycles
FSnr Warning Cooling fan issue
FUXX Stops Upper cavity motor
(XX = failure
oven
00 - 17)
Boiler gas burner
GbbU Stops the
boiler locked
GbCd Cycle Cavity lower burner
paused locked
Possible causes
• Missing water in the
boiler (electric heated
appliances only);
• Limestone accumulation
in the boiler;
• The parameter BOT is
set too low.
• The cavity is dirty;
• The parameter COT is
set too low.
Misuse
Diagnostic according to
error number (from 00 to
17) displayed.
• Water supply valve
closed or partly closed;
• Temporary lack of water
supply pressure;
• Boiler water level sensor
failure;
• Boiler leakage: drain
valve or fracture.
• Inlet air filter dirty
• Cooling fan failure
Diagnostic according to
error number (from 00 to
17) displayed.
• Air in gas supply;
• Gas supply is closed;
• Issue with the electric
supply of the burner
system;
• Burner system internal
failure;
• Air in gas supply;
• Gas supply is closed;
• Issue with the electric
supply of the burner
system;
• Burner system internal
failure;
Actions
• Wait for the boiler temperature to cool down
(alarm ETUB will disappear)
• Run a cleaning program including the rinse
and descale cycle and use 2 tabs C25 only.
(Follow the procedure as per User Manual)
• In case the alarm re-appears, descale the
boiler again.
• If the problem persists, call Service.
• Launch a cooling cycle; if not possible open
the door and let the oven to cool down;
clean the cavity.
• When the temperature drops it is possible to
launch a new cooking cycle.
• If the error shows up again call Service.
Restore the air inlet filter checking its clean-
ness before fitting it back in place. In case the
filter is lost, call Service
Switch the oven OFF/ON;
If the error persists, manually clean the oven
cavity and call Service.
• Ensure the water supply valve is fully open
and the water filter has no obstructions
(clean it if needed).
• The oven can continue to work in Convec-
tion mode
• Unless the water is missing from the mains,
the oven can continue to work in recovery
mode.
• Call Service to restore boiler functionality.
• Clean inlet air filter;
• Check with a thin strip of paper whether a
consistent air flow can be detected at the
cooling air inlet: if not, call Service.
Switch the oven OFF/ON;
If the error persists, manually clean the oven
cavity and call Service.
The oven can continue to work both in con-
vection and ISG mode.
To recover full boiler functionality:
• Switch the oven OFF/ON.
• If the error occurs at the cycle start, call
Service.
• If the error occurs after 5 ignition attempts:
1. check the gas supply main valve is open
2. reset the error and attempt new cycle
3. if the error persists, switch OFF/ON the
oven and attempt new cycle again;
4. if the error persists, call Service
The oven will not operate until restoring the
burner functionality.
To recover the functionality:
• Switch the oven OFF/ON.
• If the error occurs at the cycle start, call
Service.
• If the error occurs after 5 ignition attempts:
1. check the gas supply main valve is open
2. reset the error and attempt new cycle
3. if the error persists, switch OFF/ON the
oven and attempt new cycle again;
4. if the error persists, call Service
57