Electrolux Combi TOUCH User Manual page 55

Anom- Type of
Description
aly anomaly
CFbL Warning Cooling fan failure
CntC Stops Cavity SSR NTC fail-
cooking ure (NTC3)
CPUA Stops ACS micro does not
oven communicate
CPUt Stops TC micro does not
oven communicate
CSHt Warning Cavity SSR NTC high
temperature (NTC3)
CSOt Stops Cavity SSR NTC
cooking overtemperature
cycle (NTC3)
dESC Stops Clean Boiler
boiler
Boiler thermocouple
EbOL Stops
cycle/ failure
preheating
EbYP Warning Steam exhaust tem-
perature sensor
failure.
ECEd Stops Bottom cavity thermo-
couple failure
cycle
Bottom cavity thermo-
ECEu Stops
cycle couple failure
EH2O Stops Water measured
oven inconsistent with
valves state
Possible causes
• Cooling fan motor over-
load due to dirt or
oxidation
• Other electrical/
mechanical issue
• Connector failure;
• NTC sensor failure;
• PCB failure;
PCB failure.
PCB failure.
• Inlet air filter dirty;
• Cooling fan failure,
• Cooling inlet air sucking
warm/hot air;
• Oven installed by hot
machine;
• Steam/Heat leakage in
the electronic
compartment;
• Inlet air filter dirty;
• Cooling fan failure;
• Cooling inlet air sucking
warm/hot air;
• Oven installed by hot
machine;
• Steam/Heat leakage in
the electronic
compartment;
Scale in the boiler
• Connector failure;
• TC sensor failure;
• PCB failure.
• Connector failure;
• TC sensor failure;
• PCB failure.
• Connector failure;
• TC sensor failure;
• PCB failure.
• Connector failure;
• TC sensor failure;
• PCB failure.
• Water supply valve
closed or partly closed;
• Temporary lack of water
supply pressure;
• Flow meter failure;
• Water system issue.
Actions
The oven will be operative until the electronic
will reach the critical temperature.
Call Service
• Restart the oven;
• If the error persists, call Service.
• Restart the oven;
• If the error persists, call Service.
• Restart the oven;
• If the error persists, call Service.
• Do not switch the oven Off;
• Wait for the temperature to decrease;
• Clean the inlet air filter;
• Check with a thin strip of paper whether a
consistent air flow can be detected at the
cooling air inlet: if not, call Service;
• Check if the inlet cooling air may be affected
by heat produced in the kitchen (in case the
oven is located by hot appliances, stop
working with those appliances and inform
Service);
• If the error persists, call Service.
The oven can continue to work in recovery
mode: cooking cycles will not use the boiler.
• Do not switch the oven OFF;
• Wait for the temperature to decrease;
• Clean the inlet air filter;
• Check with a thin strip of paper whether a
consistent air flow can be detected at the
cooling air inlet: if not, call service;
• Check if the inlet cooling air may be affected
by heat produced in the kitchen (in case the
oven is located by hot appliances, stop
working with those appliances and inform
Service);
• If the error persists, call Service.
Run a cleaning program including the rinse
and descale cycle and use 2 tabs C25 only.
(Follow the procedure as per User Manual)
The oven can continue to work without pre-
heating (check the cooking results).
• Inform Service about the failure.
The oven can continue to work, it is possible
that water consumption increases.
Call Service.
The oven can continue to work only with 100
℃ cycle.
Call Service.
The oven can continue to work only with 100
℃ cycle.
Call Service.
The oven can continue to work (check the
cooking results).
• Check if the water supply valve is open;
• Check the water pressure is > 1,5 bar;
• If the problem, persists call Service.
55