Download Print this page

Toshiba 1600XPi Series Installation And Operation Manual

Single phase - 3.6/5.2/6/8/10/14/18/22 kva
Hide thumbs

Advertisement

Quick Links

INSTALLATION AND OPERATION MANUAL
Part # 60616-0014
October 2019
Manufactured in the USA
© Copyright 2019 TOSHIBA International Corporation
All rights reserved.
1600XPi SERIES
SINGLE PHASE - 3.6/5.2/6/8/10/14/18/22 KVA

Advertisement

loading

  Also See for Toshiba 1600XPi Series

  Related Manuals for Toshiba 1600XPi Series

  Summary of Contents for Toshiba 1600XPi Series

  • Page 1 1600XPi SERIES INSTALLATION AND OPERATION MANUAL SINGLE PHASE - 3.6/5.2/6/8/10/14/18/22 KVA Part # 60616-0014 October 2019 Manufactured in the USA © Copyright 2019 TOSHIBA International Corporation All rights reserved.
  • Page 3 The instructions contained in this manual are not intended to cover all of the details or variations in equipment, or to provide for every possible contingency concerning installation, operation, or maintenance. Should further information be required or if problems arise which are not covered sufficiently, contact your Toshiba sales office or call Toshiba Power Electronics Division at 855-803-7087 Nothing in this manual shall alter Toshiba International Corporation’s standard terms and conditions or the...
  • Page 4 UNINTERRUPTIBLE POWER SYSTEM (UPS) Please complete the following information and retain for your records. JOB NUMBER MODEL NUMBER SERIAL NUMBER APPLICATION SHIPMENT DATE INSTALLATION DATE INSPECTED BY 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 5 Toshiba International Corporation reserves the right, without prior notice, to update information, make product changes, or discontinue any product or service identified in this publication. Toshiba is a registered trademark of the Toshiba Corporation. All other product or trade references appearing in this manual are registered trademarks of their respective owners.
  • Page 6 This Page Left Intentionally Blank...
  • Page 7: Table Of Contents

    10.2 Battery Parameter Settings ........................22 10.3 Starting the UPS (Normal) ...........................23 10.4 Stopping the UPS ............................24 Display and Keys ........................25 11.1 Front Panel Layout ............................25 11.2 Display Manual Controls ..........................25 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 8 System Fault Messages ..........................57 23.4 System Warning Messages .........................58 23.5 System Mode Messages ..........................60 23.6 System Status Messages ..........................60 Preventive Maintenance/Parts Replacement ................. 61 24.1 Preventive Maintenance ..........................61 24.2 Cleaning the Touchscreen ...........................62 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 9 Appendix C: 1600XPi Dimensions and Weights ................C1 Appendix D: Battery Backup Tables (Internal & External Battery Cabinets) ......D1 Appendix E: External Battery Cabinets (Matching) - Outlines ............. E1 Appendix F: External Battery Cabinets (Non-Matching) ............... F1 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 10 This Page Left Intentionally Blank...
  • Page 11: General Safety Instructions

    Ground Symbol indicates the location of the equipment grounding conductor. Electrical – Voltage & Shock Hazard Symbol indicates parts inside may cause electric shock. Explosion Hazard Symbol indicates parts may explode. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 12: Signal Words

    2. This device must accept any interference received, including interference that may cause undesired operation. Notice: The FCC regulations provide that changes or modifications made to this device that are not approved by Toshiba International Corporation may void the authority granted to the user by the FCC to operate this equipment.
  • Page 13: Unintended Usage

    Transportation Equipment Always consult highly trained and qualified technicians in these applications. Improper use of the UPS system in any of the above applications may result in serious personal injury or death. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 14: Equipment Warning Labels

    Incorrect fu se replacem ent size equipment damage. may result in fire or inadeq uate equ ipm ent protection. Re pla ce only with same t ype and rating of fuse. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 15 14 15 16 17 208V 240V (L*) (N*) (0V*) 208/240V 208V 240V INPUT VOLTAGE REMOTE 120V 120V JUMPER SELECTION ( *) FOR SINGLE HOT WIRE INPUT OUTPUT P/N 63093 - Power Terminal Label 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 16: Important Safety Instructions

    2. The maximum ambient operating temperature is 104 °F (40 °C). 3. Access panels should only be removed by authorized Toshiba field Service personnel. 4. UPS servicing should be performed by qualified Toshiba representatives only. 5. Battery servicing should be performed by qualified Toshiba representatives only.
  • Page 17: Qualified Personnel Only

    WARNING Contact with any part of a grounded battery can result in electrical shock. The likelihood of shock will be reduced if such grounds are removed prior to installation or maintenance. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 18: Inspection/Storage/Disposal

    NOTE: Battery Pack cases are ABS Plastic No. 7. Please help our Earth by contacting the environmental protection agencies in your area, the battery manufacturer, or call Toshiba toll-free at (877) 867-8773 for more information about recycling. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 19: Installation Precautions

    3. Follow the instructions on the unpacking label affixed to the exterior of the UPS. 4. Retain the shipping rails for use as permanent mounting of the UPS. fig 1 fig 2 Unpacking Instructions P/N 48537 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 20 Always ground the unit to reduce the potential for electrical shock and to help reduce electrical noise. d. A separate ground cable should be run inside the conduit with the input power, output power, and control circuits. WARNING THE METAL OF CONDUIT IS NOT AN ACCEPTABLE GROUND. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 21: Operating Precautions

    11. If the UPS should emit smoke, produce an unusual odor, or make sound, turn the power off immediately. 12. Changing/replacing the UPS Batteries should only be performed by Toshiba field service personnel. 13. Warning signs should be placed on or near the load as a notification that the load is being powered by the UPS.
  • Page 22: Ups Connections

    NOTE 1 – If AC input power is 208 Vac rated, short terminals 11 and 12 with a jumper wire. DO NOT jumper terminal 13 to 12 or 11. Factory Setting is 208 Vac. Use the jumper wire provided by Toshiba. DO NOT add any additional jumpers.
  • Page 23 Factory Installed N - G Jumper Connect load across terminals 5 – 7. 208 Vout 240 Vout Connect load across terminals 4 – 7. Factory Installed N - G Jumper 240 Vout 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 24: Terminal Block

    Connect load across Terminals 4 – 6 or 6 – 7. Connect load across terminals 4 – 7. Factory Installed N - G Jumper Factory Installed N - G Jumper 100 V 100 V 200 Vout 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 25: Epo And Remote Shutdown

    Optional external battery cabinets can be used to extend the backup time of the UPS beyond that available with the internal batteries. The external battery cabinets connect to the UPS via Anderson-style connectors. See Section 20. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 26: Product Description

    Application and Use Toshiba 1600XPi Series of On-Line UPS provides continuous computer-grade AC power in a compact, high performance, and energy efficient unit. The UPS unit ensures safe and reliable operation of critical office equipment. All units feature an audible alarm which sounds if the battery voltage drops below a specified minimum during use.
  • Page 27: Operating Modes

    POWER FLOW IN ON-LINE MODE FOR ALL MODELS *Surge Absorber is connected as indicated in 3.6–10kVA units. Surge Absorber is connected at the point between the Line Filter and Input Fuse in 14–22kVA units. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 28: Battery Backup (On Batteries)

    POWER FLOW AFTER AN EPO COMMAND FOR ALL MODELS *Surge Absorber is connected as indicated in 3.6–10kVA units. Surge Absorber is connected at the point between the Line Filter and Input Fuse in 14–22kVA units. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 29: Battery Backup Time And Discharge Process

    246 Vdc 246 Vdc 246 Vdc Shutdown voltage (Vmin) 114 Vdc 170 Vdc 227 Vdc 227 Vdc 227 Vdc 227 Vdc 227 Vdc Note: Above values are based on full-rated load. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 30: Battery Recharging

    10 kVA 327 V 227 V 1.0 A 14 kVA 327 V 227 V 1.0 A 18 kVA 327 V 227 V 1.0 A 22 kVA 327 V 227 V 1.0 A 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 31: Battery Test

    If the test fails, the display returns to the Monitor screen and displays BTSTFL in the warning section at the bot- • tom left of the display, and the “Warning” LED blinks until the fault is cleared. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 32: Operating The Ups

    11. After setup is completed, log back in as USER. See section 14.3 for guidance. 10.2 Battery Parameter Settings Table 11-1 for setting the battery parameters during initial setup for these configurations: Stand-alone UPS; UPS + 1 Battery Cabinet; UPS + 2 Battery Cabinets. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 33 See Note 3 External Battery Capacity in A-hr 1 Battery runtimes on the UPS display will not be accurate when using a non-Toshiba external battery cabinet. 2. Internal battery trays MUST be removed before connecting UPS to non-matching battery cabinet.
  • Page 34: Starting The Ups (Normal)

    Any load devices will lose power. Ensure that all sensitive loads have been previously shut down. To completely stop the UPS, turn the input breaker at the back of the UPS to the OFF position. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 35: Display And Keys

    Display Contrast Adjustment – The display is shipped with the display adjusted for optimum visibility. If necessary use a trimmer adjustment tool to fine tune the display contrast for improved visibility. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 36: Lcd Touchscreen Layout

    Security Level – Pressing the Security Level key activates the log-in security screen. (Speaker) – Pressing the Speaker key will disable/enable the audible alarm. Touchscreen Lock – Locks touchscreen except for this key. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 37: Operating Keys

    Menu selection under Monitor and Settings tabs. 2 / 3 Shows the current page or record number, and total number of pages or records. Go to Next Page/Record Key. Go To Last Page/Record Key. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 38: Status Indicators

    Green - Flashing Input voltage is over specified range. Green - OFF Input voltage is under specified range. AC Input NOTE: On-Line/Fault LEDs - Appear Amber if Green and Red flash concurrently. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 39: Touchscreen Menu Tree

    Faults Warnings In any record set, if more than 32 inci- Operation System dences have occurred, only the most recent 32 record are retained in each report. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 40: Keypad Controls

    KEYPAD 100% 12:35 PM HOME Main Monitor Settings Records 619 Change Secu. Lvl Quit 2abc 3def Write 4ghi 5jkl 6mno 7pqrs 8tuv 9wxyz Backspace Shift “Space” DVCOH ASYN On-Line SHIFTED KEYPAD 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 41: Screen: Security Passwords & Keypad

    Use the page (<< and >>) and record (< and >) keys to select Cmd 621 - Reset Admin PWD. Press Reset. Press Write to store the default password in the UPS. If the password is accepted the text “Successful” will display. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 42: Screen Tab: Main

    Touching the lockout key again will toggle the lockout off, the graphic will change to indicating the touch- UPS Serial Number screen is active. 20080112345 UPS Typeform UXPB2B100C6 STOP ASYN On-Line DVCOH MAIN SCREEN DISABLED 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 43: Screen Tab: Monitor

    Monitor Settings Records Main Monitor Settings Records C&C D&E C&C D&E C&C D&E DVCOH ASYN Backup DVCOH ASYN Shutdown DVCOH ASYN On-Line BACKUP MODE OUTPUT SHUTDOWN MODE MIMIC DISPLAY STATUS INDICATOR 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 44 854 Reye Gway IP BAT parameters. 614 UPS Status (Comm) 00X00400060 855 SReye Not installed 615 RunStop SW Status Stop D&E 1/2 C&C 1/2 ASYN On-Line DVCOH DVCOH ASYN On-Line 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 45: Battery Mimic Display (Bat)

    585 BC1 AmbientTemp 29 C Voltage DC: 280 V Monitor Charge %: 90 % Current: External Battery 2 1.00 A BAT 1/1 EXTBC1 EXTBC1 DVCOH On-Line DVCOH On-Line DVCOH EXTBC1 On-Line 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 46 If a fault occurs in one of the External Battery Cabinet battery strings, correct the fault then reset the UPS by pressing the RESET switch on the lower right side of the display panel. (See Section 12.1) 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 47: Audible Alarm Functions

    The buzzer can be disabled by selecting the Settings tab then setting the Mbuzzer parameter to 0. This will disable the alarm so that no alarm sounds for any Fault or Warning condition. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 48: Screen Tab: Settings

    (850-859) lists the RemotEye 4 IP address, IP Mask, Status, Baud Rate, datalink status. 12:35 PM 100% HOME Main Monitor Settings Records Input Output Bypass DC Bus Batt Ctrl/Cfg History Debug Disp/Reye On-Line SETTINGS OPENING SCREEN 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 49 706 Hi Battery Temp -8 C 807 TMRsleep 10 Min C&C 1/5 HIS 1/4 D&E 1/4 DVCOH ASYN On-Line DVCOH ASYN On-Line DVCOH ASYN On-Line CTRL/CFG (SCC)BLOCK HISTORY BLOCK DISP/REYE BLOCK 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 50: Changing Ups Parameter Settings

    Settings Records parameter for change will generate the message “Item cannot be changed”. Item cannot be changed Press OK to return to the original display. 1 / 32 DVCOH ASYN On-Line 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 51: Settings Parameters

    Example - Shows an example of the parameter displayed on the touchscreen. • Rqd Security Level to Change/By - The required security level to change a parameters value or setting: User, Ad- ministrator, Distributor. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 52: Recalibrate The Touchscreen

    After completing Step 10, the display will return to the Cali Display screen. Press the Quit key. The touchscreen has been successfully recalibrated and the resulting values stored on the Control PCB. CALIBRATION SCREEN 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 53: Screen Tab: Records

    Vout Vout 101 % 101 % Iout Iout Vbend Vbst Vbst On-Line Backup From BypNorm Trigger source: ViVU Branch 1 / 2 1 / 32 ASYN On-Line ASYN On-Line DVCOH DVCOH 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 54: Communication Interfaces

    Pin switches are shown in their inactive states. For example, if battery voltage is low, pin 7 will be connected to pin 5. When not applying +3 to +15V, the voltage supplied to pins 2 and 3 should be reverse biased (-3 to -15V) to avoid unintentional closure due to signal noise. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 55: Ups Lan Shutdown Signal Operation

    This pin is not used Input Receive data Output Transmit data Output Data terminal ready Signal ground Input Data set ready Output Request to send Input Clear to send This pin is not used 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 56: Remoteye Network Card

    18.4 RemotEye Network Card The RemotEye 4 is the network communication card for the Toshiba UPS. The RemotEye communications card is pre- installed as a standard with the 1600XPi. This card slides into a slot located on the back side (See illustration) of the UPS.
  • Page 57: Optional) Emd

    RJ-45 PORT ENVIRONMENTAL MONITORING MODULE (EMD) Smoke Detector Motion Sensor Intrusion Sensor Liquid Sensor EMD SENSORS 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 58: Optional Mb (Maintenance Bypass) Units

    2. Turn the Maintenance Bypass switch to the UPS position. The UPS LED should be ON and the Bypass LED OFF. 3. Turn the RUN/STOP switch to the RUN position on the UPS. The UPS is now operating in the UPS Mode. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 59: Optional) External Two-Breaker Maintenance Bypass

    MAINTENANCE BYPASS CBL1 MAIN UTILITY CBL2 OUTPUT PANEL: 3Φ CBM1 LOAD CBM2 PANEL 208V 120V DO NOT USE 3-PHASE INPUT WHEN USING THIS EXTERNAL MAINTENANCE BYPASS 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 60: Optional) External Three-Breaker Maintenance Bypass (No Transformer)

    The output of the UPS and the utility feed have different phase to neutral references and transfer between the two could cause loss of power or damage to the load. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 61: Optional) External Three-Breaker Maintenance Bypass (With Transformer)

    208/120V source in this system configuration. X1/X2 MIB1 MIB2 UTILITY PANEL: MAIN OUTPUT 3Φ MBB1 MBB2 UTILITY PANEL: SINGLE Φ LOAD 120/208/240V PANEL UIB1 UIB3 UIB2 UIB4 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 62: Optional Tvss (Transient Voltage Surge Suppressor)

    All models of the 1600XPi UPS ending in -TVS are equipped with a TVSS (Transient Voltage Surge Suppressor. The TVSS is mounted on the back of the UPS and is factory wired to the input as shown below. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 63: External Battery Cabinet Connections

    Circuit Breaker) UPS Model Battery Cabinet MCCB Capacity 3.6, 5.2, 6 kVA 50 A 8, 10, 14, 18, 22 kVA 100 A See the applicable battery cabinet manual for additional details. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 64: Optional Receptacle Panel Installation Instructions

    Attach the screws removed from the cover plate through the mounting holes of the receptacle panels and back into the UPS mounting points. Mounting Mounting Screws Receptacle Panel Connector Figure 1 Figure 2 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 65: Ups Protection System

    Bypass OL: Bypass relay open Inverter OL: Yes if bypass is OK Auto-retransfer Bypass OL: No UPS FAULT PROTECTION FUNCTIONS (CONT.) Protection Item Ambient Overheat DC Circuit Overvoltage DC Circuit Overcurrent LCD Message DCOV DCOC 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 66 Shutdown – No output Fault Inverter OL – Transfer to bypass Audible Alarm Yes – Continuous buzzer Visible Alarm Red Fault LED on Fault relay closed Relay Contact Alarm Bypass relay closed Auto-retransfer 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 67: System Fault Messages

    BC1 Battery String 1, 2, or 3 Call Toshiba for Service. Loose HCT Connection • BC1 Over Voltage Fault Call Toshiba for Service • BC1 Over Current Fault Call Toshiba for Service 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 68: System Warning Messages

    77 °F (25 °C) may decrease battery’s scheduled service life.) BLFN Battery Lifetime Near End – Bat- Battery has 6 months or less of scheduled service teries are nearing the end of their life. expected lifetime. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 69 Immediately shut down the load equipment in an has dropped low (about 90% or orderly fashion and then press the STOP key. less) during operation. Continued operation in this mode will deplete battery and cause output shut down. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 70: System Mode Messages

    No action needed. startup. EE1ST EEPROM is loaded with default values. No action needed. EE2RAERR EEPROM to RAM loading Error. Call Toshiba for service. EEUPERR EEPROM updating Error. Call Toshiba for service. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 71: Preventive Maintenance/Parts Replacement

    24.1 Preventive Maintenance Toshiba 1600XPi Series of uninterruptible power systems have been designed to provide years of trouble-free operation requiring a minimum of preventive maintenance. The best preventive measure that the UPS user can take is to keep the area around the unit, particularly the air inlet vents, clean and free of moisture and dust accumulations.
  • Page 72: Cleaning The Touchscreen

    3.6, 5.2, 6, 8, 14, and 18 kVA P/N 51896-FS Battery Tray Plug for: 10 and 22 kVA P/N 60995-FS (Dual conductors because of higher battery pack dis- charge current) 1600XPI BATTERY TRAY PLUG DIFFERENCES 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 73 6.3 Notify the factory if the battery pack still will not fully seat in the receptacle, and a cause cannot be deter- mined. 7. Repeat steps 3-6 for remaining battery packs. 8. Reinstall battery pack retaining plates. 9. Close the front door. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 74: Part Replacement

    Approximately 2.5 yrs. 104 °F (40 °C) Approximately 1.8 yrs. 113 °F (45 °C) Approximately 1.25 yrs. * Continual operation at ambient temperatures above 25 °C will degrade the battery life. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 75: External Layouts/Dimensions/Shipping Weights

    (904 mm) (904 mm) 2.4 in. 2.4 in. 2.6 in. 2.6 in. 3.4 in. 3.4 in. 3.4 in. (61 mm) (61 mm) (65 mm) (65 mm) (87 mm) (87 mm) (87 mm) 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 76: External Layout

    25.4 External Layout RemotEye 4 Slot Remote Contacts Port (Male) RS232 Port (Female) Terminal MCCB Block Cover External Layout for 3.6kVA and 6kVA units 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 77 SNMP Port Remot- (Remote Eye 4 -Eye III Slot Slot) SNMP Port Remot- (Remot Eye 4 -Eye III Slot Slot) 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 78 This Page Left Intentionally Blank...
  • Page 79: Appendix A: 1600Xpi Specifications

    If Vin is below the minimum Vin window, the UPS goes to Battery Mode. If the UPS is in Fault and Vin is below the minimum Vin window, the UPS goes to Bypass Mode 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 80 204 volts; otherwise, ratings given for 0.70PF are applicable. At 6600 ft (2000 m) above sea level, output capacity should be derated by 3% per additional thousand feet elevation. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 81 Input/output figures rated for 240 volts unless otherwise stated. Output ratings given for 0.85PF are only valid when the input voltage is greater than 204 volts; otherwise, ratings given for 0.70PF are applicable. Remove all sources of main AC power and wait five minutes before replacing fans. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 82 If Vin is below the minimum Vin window, the UPS goes to Battery Mode. If the UPS is in Fault and Vin is below the minimum Vin window, the UPS goes to Bypass Mode. If UPS is in Bypass mode and Vin is outside the acceptable range, the goes to Shutdown Mode. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 83 At 6600 ft (2000 m) above sea level, output capacity should be derated by 3% per additional 1000 feet elevation. Subject to update without notice. Derate to 18.7 kVA (15.9 kW) for 50 Hz operation. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 84 Input/output figures rated for 240 volts unless otherwise stated. Output ratings given for 0.85PF are only valid when the input voltage is greater than 204 volts; otherwise, ratings given for 0.70PF are applicable. Derate to 18.7 kVA (15.9 kW) for 50 Hz operation. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 85 If Vin is below the minimum Vin window, the UPS goes to Battery Mode. If the UPS is in Fault and Vin is below the minimum Vin window, the UPS goes to Bypass Mode 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 86 204 volts; otherwise, ratings given for 0.70PF are applicable. At 6600 ft (2000 m) above sea level, output capacity should be derated by 3% per additional thousand feet elevation. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 87 Input/output figures rated for 240 volts unless otherwise stated. Output ratings given for 0.85PF are only valid when the input voltage is greater than 204 volts; otherwise, ratings given for 0.70PF are applicable. Remove all sources of main AC power and wait five minutes before replacing fans. 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 88 This Page Left Intentionally Blank...
  • Page 89 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 90 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 91 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 92 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 93 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 94 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 95 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 96 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 97 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 98 B-10 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 99 1600XPi Series UPS Installation and Operation Manual – 60616-014 B-11...
  • Page 100 B-12 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 101 1600XPi Series UPS Installation and Operation Manual – 60616-014 B-13...
  • Page 102 B-14 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 103 1600XPi Series UPS Installation and Operation Manual – 60616-014 B-15...
  • Page 104 B-16 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 105 1600XPi Series UPS Installation and Operation Manual – 60616-014 B-17...
  • Page 106 B-18 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 107 1600XPi Series UPS Installation and Operation Manual – 60616-014 B-19...
  • Page 108 B-20 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 109 1600XPi Series UPS Installation and Operation Manual – 60616-014 B-21...
  • Page 110 B-22 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 111 1600XPi Series UPS Installation and Operation Manual – 60616-014 B-23...
  • Page 112 B-24 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 113 1600XPi Series UPS Installation and Operation Manual – 60616-014 B-25...
  • Page 114 B-26 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 115 1600XPi Series UPS Installation and Operation Manual – 60616-014 B-27...
  • Page 116 B-28 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 117 1600XPi Series UPS Installation and Operation Manual – 60616-014 B-29...
  • Page 118 This Page Left Intentionally Blank...
  • Page 119: Appendix C: 1600Xpi Dimensions And Weights

    Appendix C: 1600XPi Dimensions and Weights 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 120 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 121 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 122 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 123: Appendix D: Battery Backup Tables (Internal & External Battery Cabinets)

    0.85 15.00 0.30 0.85 15.00 0.40 1224 0.85 15.00 0.50 1530 0.85 15.00 0.60 1836 0.85 15.00 0.70 2142 0.85 15.00 0.80 2448 0.85 15.00 0.90 2754 0.85 15.00 1.00 3060 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 124 25.00 0.30 1530 0.85 25.00 0.40 2040 0.85 25.00 0.50 2550 0.85 25.00 0.60 3060 0.85 25.00 0.70 3570 0.85 25.00 0.80 4080 0.85 25.00 0.90 4590 0.85 25.00 1.00 5100 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 125 33.33 0.30 2040 0.85 33.33 0.40 2720 0.85 33.33 0.50 3400 0.85 33.33 0.60 4080 0.85 33.33 0.70 4760 0.85 33.33 0.80 5440 0.85 33.33 0.90 6120 0.85 33.33 1.00 6800 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 126 41.67 0.30 2550 0.85 41.67 0.40 3400 0.85 41.67 0.50 4250 0.85 41.67 0.60 5100 0.85 41.67 0.70 5950 0.85 41.67 0.80 6800 0.85 41.67 0.90 7650 0.85 41.67 1.00 8500 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 127 58.33 0.30 3570 0.85 58.33 0.40 4760 0.85 58.33 0.50 5950 0.85 58.33 0.60 7140 0.85 58.33 0.70 8330 0.85 58.33 0.80 9520 0.85 58.33 0.90 10710 0.85 58.33 1.00 11900 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 128 75.00 0.30 4590 0.85 75.00 0.40 6120 0.85 75.00 0.50 7650 0.85 75.00 0.60 9180 0.85 75.00 0.70 10710 0.85 75.00 0.80 12240 0.85 75.00 0.90 13770 0.85 75.00 1.00 15300 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 129 91.67 0.30 5610 0.85 91.67 0.40 7480 0.85 91.67 0.50 9350 0.85 91.67 0.60 11220 0.85 91.67 0.70 13090 0.85 91.67 0.80 14960 0.85 91.67 0.90 16830 0.85 91.67 1.00 18700 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 131: Appendix E: External Battery Cabinets (Matching) - Outlines

    Appendix E: External Battery Cabinets (Matching) - Outlines 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 132 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 133: Appendix F: External Battery Cabinets (Non-Matching)

    * Runtime will vary due to differences in battery manufacture, age, temperature, load, life-cycle, and utilization profile. Notes: • Additional runtime can be achieved by adding additional battery cabinets. Contact your Toshiba representative for details. • Estimated runtime and SOC on LCD will be not accurate with non-matching type battery cabinet,...
  • Page 134 TABLE F-2 - NON-MATCHING BATTERY CABINET DIMENSIONS Battery Depth Height Width Cabinet 29 in. 31.5 in 59 in. 36 in. 29.5 in. 70.7 in. Figure F.1 - Relative Sizes of External Non-matching Battery Cabinets 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 135 A4 overload capacity A5 output A4 switch A5 Warning 11 Fuse 62 cable 15 capacitors 62 ground Certifications A1 terminals 15 Clock 26 current charging 20 Initial Startup (First Power-Up) 22 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 136 Settings 38 Run 25 monitoring battery 35 Safety instructions 1 Security Normal input power supply 44 access 31 passwords 31 Shutdown voltage 19 Off 25 size operation battery packs A6 modes 58 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 137 27 keypad 30 mimic display 33 passwords 31 screen disable 32 Discharge Process 18 UPS functional overview 16 ventilation 11 warning message 56 warning labels 4 Warranty c Weights, shipping 63 1600XPi Series UPS Installation and Operation Manual – 60616-014...
  • Page 138 This Page Left Intentionally Blank...
  • Page 140 SOCIAL INFRASTRUCTURE SYSTEMS GROUP POWER ELECTRONICS DIVISION 13131 West Little York Road, Houston, Texas 77041-9990 Tel (713) 466-0277 Fax. (713) 466-8773 US (855) 803-7087 Canada (800) 872-2192 https://www.toshiba.com/tic/industrial/uninterruptible-power-systems Printed in the U.S.A.