Parameter List For Point Table; Timing Chart; Power On - HNC Electric SV-E3 Series Instruction Manual

659. 0 [Special setting]
Home position
return Timeout
Time

6.2 Parameter list for point table

Table 6.2.1 Parameter list for point table
Point Position Rotation
No. [Command speed
pulse] [r/min]
0 No.722.0 No.724.0
1 No.742.0 No.744.0
2 No.762.0 No.764.0
3 No.782.0 No.784.0
4 No.802.0 No.804.0
5 No.822.0 No.824.0
6 No.842.0 No.844.0
7 No.862.0 No.864.0
8 No.882.0 No.884.0
9 No.902.0 No.904.0
10 No.922.0 No.924.0
11 No.942.0 No.944.0
12 No.962.0 No.964.0
13 No.982.0 No.984.0
14 No.1002.0 No.1004.0
15 No.1022.0 No.1024.0

7. Timing chart

7.1 Power ON

Figure 7.1.1 Power ON
Set Home position return Timeout Time.
[Initial value] 60,000[10ms]
[Setting range] 0 to 60,000
Acceleration Deceleration
time [ms] time [ms]
No.726.0 No.727.0
No.746.0 No.747.0
No.766.0 No.767.0
No.786.0 No.787.0
No.806.0 No.807.0
No.826.0 No.827.0
No.846.0 No.847.0
No.866.0 No.867.0
No.886.0 No.887.0
No.906.0 No.907.0
No.926.0 No.927.0
No.946.0 No.947.0
No.966.0 No.967.0
No.986.0 No.987.0
No.1006.0 No.1007.0
No.1026.0 No.1027.0
Command Dwell time
method [-] [ms]
No.720.0 No.728.0
No.740.0 No.748.0
No.760.0 No.768.0
No.780.0 No.788.0
No.800.0 No.808.0
No.820.0 No.828.0
No.840.0 No.848.0
No.860.0 No.868.0
No.880.0 No.888.0
No.900.0 No.908.0
No.920.0 No.928.0
No.940.0 No.948.0
No.960.0 No.968.0
No.980.0 No.988.0
No.1000.0 No.1008.0
No.1020.0 No.1028.0
83
No
Running Positioning
operation [-] completion
[Encoder
pulse]
No.720.1 No.729.0
No.740.1 No.749.0
No.760.1 No.769.0
No.780.1 No.789.0
No.800.1 No.809.0
No.820.1 No.829.0
No.840.1 No.849.0
No.860.1 No.869.0
No.880.1 No.889.0
No.900.1 No.909.0
No.920.1 No.929.0
No.940.1 No.949.0
No.960.1 No.969.0
No.980.1 No.989.0
No.1000.1 No.1009.0
No.1020.1 No.1029.0
valid/ Invalid
[-]
No.720.3
No.740.3
No.760.3
No.780.3
No.800.3
No.820.3
No.840.3
No.860.3
No.880.3
No.900.3
No.920.3
No.940.3
No.960.3
No.980.3
No.1000.3
No.1020.3